Question about 2005 Chevrolet Equinox

Open Question

What is the torque tightening value for the front caliper mounting guide pin bolts and the caliper mounting bracket bolts for a 2005 Chev Equinox?

Posted by on

  • roddy chippeway May 11, 2010

    about 140 just use a breaker bar or a long wrench

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 33 Answers

SOURCE: Need the correct torque specs for 2004 silverado 1500 calipers

  • Tighten the 2 brake caliper mounting bolts to 108 Nm (80 ft. lbs.) . Caliper Mounting Bracket to Knuckle, Front (15 series) 175 Nm (129 ft. lbs.) Caliper Mounting Bracket to Knuckle, Front (25/35 series) 300 Nm (221 ft. lbs.) Brake Caliper Mounting Bolt Rear (15 series) 42 Nm (31 ft. lbs.) Brake Caliper Mounting Bolt Rear (25/35 series) 108 Nm (80 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JC5/JH5) 200 Nm (148 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JH6) 165 Nm (122 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JH7) 300 Nm (221 ft. lbs.) Caliper Mounting Bracket Bolt Rear (NYS) 200 Nm (148 ft. lbs.)
    hope this helps
  • Posted on Mar 28, 2009

    • 72 Answers

    SOURCE: Front Hub Bearing Torque specs to complete replacement

    THE LUG NUT TORQUE SPEC - 140FT/LBS\
    CALIPER MOUNT - 80FT/LBS
    CALIPER BRACKET 129FT/LBS
    AXLE NUT 177FT/LBS

    Posted on May 09, 2009

    • 333 Answers

    SOURCE: Replacing front wheel hub assembly on 2006

    Caliper mount bolts are 74 ft/lbs
    Driveshaft axle nut is 177 ft/lbs
    Hub and bearing mounting bolts are 133 ft/lbs

    Posted on Sep 10, 2009

    Testimonial: "The info on the torgue specs was very helpful. I couldn't find it anywhere. Thanks a bunch!"

    • 226 Answers

    SOURCE: cannot remove rear brake caliper

    Try using a "c" clamp and push the piston in all the way on the caliper. Take the lid off the master cyl first. Lee

    Posted on Oct 11, 2009

    c17hydro
    • 2984 Answers

    SOURCE: cyl head torque on 05 3.4l chev equinox

    ① Step 1: 44 ft. lbs. Step 2: plus 95 degrees

    Driver's side head--

    1b89d93.gif

    Install the NEW cylinder head bolts. Tighten the bolts as follows:

    • Tighten the bolts in sequence to 44 ft. lbs. (60 Nm).
    • Turn the bolts in sequence an additional 95 degrees.

    Posted on Oct 31, 2009

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    Brake Caliper torque specs for 2008 GMC Acadia front abutment bracket bolts and the Caliper bolts?


    Those are Brake Caliper Bracket Bolts - Front
    175 N?·m
    129 lb ft
    Brake Caliper Guide Pin Bolts - Front
    Tighten the guide pin bolt closest to the bleed valve first.
    64 N?·m
    47 lb ft

    Jun 03, 2016 | GMC Cars & Trucks

    2 Answers

    How to change brake pad and check rotors


    Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

    To Remove:
    1. Drain brake fluid to ½ full level in reservoir.
    2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

    3. Remove the front brake caliper assembly.
    4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
    5. Remove the wear indicator from each of the 2 brake pads.
    To Install:
    NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
    toy_car_cam_frontbrakepads.gif

    1. Using a large C clamp or equivalent press piston into the caliper.
    2. Apply disc brake grease to the inside of each anti-squeal shim.
    3. Install the anti-squeal shims on each pad.
    4. Install the pad wear indicator clip to the pads.
    5. Install the pads with the pad wear indicator plate facing upward.
    6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
    7. Install the front wheels.
    8. Fill the master cylinder with new clean brake fluid.
    9. Pump the brake pedal several times to seat the brake pads.
    Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

    TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

    To Remove:
    1. Drain the brake fluid to ½ full level in reservoir.
    2. Remove the rear wheels.
    3. Remove the caliper slide pins.
    4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
    5. Remove the rear brake calipers.
    6. Remove the 2 brake pads with the anti-squeal shims.
    7. Remove the anti-squeal shims and pad wear indicators from brake pads.
    To Install:
    1. Using a large C clamp or equivalent press the piston into the caliper.
    2. Coat both sides of the outer anti-squeal shim with pad grease.
    3. Install anti-squeal shims to each pad.
    4. Install wear indicators on the 2 brake pads.
    5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
    6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
      • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
      • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
    7. Fill the master cylinder with new clean brake fluid.
    8. Pump the brake pedal several times to seat the brake pads.
    9. Install the rear wheels.
    prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
    1. Remove the front wheels.
    2. Remove the front brake caliper assembly.
    3. Remove the front brake pads.
    4. Remove the 2 bolts and caliper mounting bracket.
    5. Place match marks on the disc and axle hub.
    6. Remove the front wheel disc.
    To Install:
    1. Align the match marks and install the front disc.
    2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
    3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
    4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
    5. Fill the reservoir with brake fluid.
    6. Bleed the brake system.
    7. Install the front wheel.
    Rear To Remove:
    1. Remove the rear wheels.
    2. Remove the brake caliper assembly.
    3. Remove the brake pads.
    4. Remove the 2 bolts and the caliper mounting bracket.
    5. Place match marks on the disc and axle hub.
    6. Remove the rear disc.
    To Install:
    1. Align the match marks and install the rear disc.
    2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
      • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
      • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
    3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
      • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
      • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
    4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
    5. Fill the reservoir with brake fluid.
    6. Bleed the brake system.
    7. Install the rear wheel
    prev.gif next.gif

    Jan 25, 2011 | 2007 Toyota Camry

    1 Answer

    Replacing front wheel barings on a 2005 chev silverado. need torque specs for 3 mounting bolts and torque spec for shaft nut through center of bearing (spline gear)


    the big one tighten with a big bar and pull it to about 120lbs ,the three smaller ones which i cannot place at the moment but if they are 17mm size heads then about 60 but i always feel them as i do them and never use a torque wrench or a air wrench ,just muscle and 40yrs of feel

    Mar 02, 2010 | 2005 Chevrolet Equinox

    1 Answer

    How do i get the calapers off the rear of a 2006 grand caravane?


    Using a C clamp depress the claiper. There a spot right in the middle to do this. Now the fun part hope you have metic hex key set. The 2 caliper guide pins are on the back inside the boots. Which need to be in great condition. Using the metic hex keys some are 7mm or 8mm turn to your right to remove. Rmove the caliper mounting bracket bolts. Fun part #2 removing the disc rotor. Theres parking brake pads or a durm brake system on the inside of the rotor. If the rotor does not slide off. You must remove the rubber gromet on the back of the backing plate. Using a screwdriver or the old brake adjuster tool turn the star wheel to adjust the parking brake in to remove the disc rotor. All brake guides on the calipers & guide pins need to have high temperture brake grease applyed to them. Buy the big bottle for $10 for the front brakes & future use it comes with a bush. Note ** Remove a guide pin take to auto store buy socket to reinstall guide pin/bolt. Why Caliper guide pins 26lbs torque. Caliper mounting bolts 125lb torque

    Dec 05, 2009 | 2006 Dodge Grand Caravan

    2 Answers

    Brake job torque spec


    Caliper bolt 25 ft lbs/ caliper bracket bolt 79.6 ft lbs

    Nov 13, 2009 | 2005 Honda Civic

    1 Answer

    Silverado 1500 Z71 off road, 5.3L. Details on fr


    This is for the front: Removal & Installation
    1. Remove 2/3 of the brake fluid from the master cylinder.
    2. Remove or disconnect the following:
      • Wheel
      • Caliper. Suspend the caliper from the frame with mechanic's wire. Do not allow the caliper to hang from the brake hose.
      • Caliper mounting bracket bolts
      • Caliper mounting bracket from the steering knuckle assembly
      • Brake pads from the caliper mounting bracket
      • Clips from the inside ends of the caliper mounting bracket and discard
    To install:
    1. Install or connect the following:
      • Clips to the inside ends of the caliper mounting bracket
      • Brake pads to the caliper mounting bracket
      • Inner pad (1 wear indicator)
      • Outer pad (2 wear indicators)
      • Caliper mounting bracket to the steering knuckle assembly
    2. Perform the following procedure before installing the caliper mounting bracket bolts:
      • Remove all traces of the original adhesive patch.
      • Clean the threads of the bolt with brake parts cleaner or the equivalent and allow to dry.
      • Apply red Loctite®272 to the threads of the bolt.
    3. Install or connect the following:
      • Caliper mounting bracket bolts to the steering knuckle. Tighten the caliper guide pin bolts to 74 ft. lbs. (100 Nm) on 15 series or 80 ft. lbs. (108 Nm) on 25/35 series.
      • Caliper
      • Tire and wheel assembly
    4. Refill the master cylinder to the proper level with fresh brake fluid. Pump the brake pedal slowly and firmly in order to seat the brake pads. Burnish the brakes as needed.

    Oct 12, 2009 | 2003 Chevrolet Silverado 1500

    3 Answers

    Small tabs next to inside front rotors rubbing. What are these for? 2005 Chev Equinox


    they are called wear indicators time to replace your brakes before they damage the rotors

    Sep 27, 2009 | 2005 Chevrolet Equinox

    1 Answer

    Torque setting for brake caliper mounting bracket


    according to manual,
    front caliper mounting bolts are 11 ft lbs
    rear caliper mounting bolts are 220 inch lbs.

    Jul 02, 2009 | 2005 Jeep Liberty

    1 Answer

    Need the correct torque specs for 2004 silverado 1500 calipers


  • Tighten the 2 brake caliper mounting bolts to 108 Nm (80 ft. lbs.) . Caliper Mounting Bracket to Knuckle, Front (15 series) 175 Nm (129 ft. lbs.) Caliper Mounting Bracket to Knuckle, Front (25/35 series) 300 Nm (221 ft. lbs.) Brake Caliper Mounting Bolt Rear (15 series) 42 Nm (31 ft. lbs.) Brake Caliper Mounting Bolt Rear (25/35 series) 108 Nm (80 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JC5/JH5) 200 Nm (148 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JH6) 165 Nm (122 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JH7) 300 Nm (221 ft. lbs.) Caliper Mounting Bracket Bolt Rear (NYS) 200 Nm (148 ft. lbs.)
    hope this helps
  • Mar 28, 2009 | 2004 Chevrolet Silverado

    Not finding what you are looking for?
    2005 Chevrolet Equinox Logo

    Related Topics:

    323 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8152 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...