Question about 1995 Isuzu Trooper

1 Answer

1995 isuzu trooper 3.2 (3 sets of wires comming from gearbox ?) dose any one no what they are for Thanx Gordon

Posted by on

  • flashmaan02 Jul 15, 2009

    Hi thanx for that
    Just a question .What is a (detent)

    Thanx Gordon

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Isuzu Master
  • 450 Answers

Detent switch has two wire bullet connectors,
another detent switch which is reverse lights that also has bullet connectors.
put blue to blue and red to red if not car will not turn off with ignition key.these are on upper section of gearbox the third is a speedo sensor at rear. one oxygen sensor at front section which could be separate section of engine harness

Posted on Jul 10, 2009

  • Steve Hurc
    Steve Hurc Jul 16, 2009

    on / off switch, ball bearing in switch housing moves over shift rail when notch cut out of shift rail comes in contact with ball, switch changes state.

    1. With ball being free

    A – B:There is continuity

    2. With ball forced into the switch

    A – B:No continuity

    3. If 1) and 2) fail, replace with a new switch.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

V6. What are the size and length of the starter mounting bolts?


Probably 12mm X 1.5mm. Length is about 1 1/2 inches and 3 1/2 inches. They are metric.

Aug 06, 2015 | 1995 Isuzu Trooper

1 Answer

Isuzu trooper duty 1995 loss of power wont rev over 1800rpm


the cars come with many diff. engines. and EFI systems that match it.
so cant help you.
but ill answer in pure physics.
1: lost DC 12v power to the EFI system causing spark and fuel losses.
2: lost engine compression. 1 or more cylinders.
3: lost spark or never doing a full tuneup every 60k at least.
4: bad fueling, too much or too little.
what do do is a few simple tools to discover the truth.

do you want to gue$$, or test.

Aug 30, 2014 | 1995 Isuzu Trooper

2 Answers

Isuzu trooper wheel discs overheating


Have you recently changed rotors?

Jun 02, 2014 | 2002 Isuzu Trooper

1 Answer

Alternator wiring or connection


The two WHT wires from 80A MAIN fuse FL-1 in the fuse/relay box connect to the B (battery) terminal. The BLK/YEL wire from 15A ENGINE fuse C-8 in the dash fuse box connects to the IG (ignition) terminal. The WHT/GRN wire from the charge warning light in the instrument panel connects to the L (light) terminal. Tre is no connection to the C terminal in the 1995 Isuzu Trooper

Dec 06, 2012 | 1995 Isuzu Trooper

1 Answer

Isuzu trooper 1995, automatic : It is not pulling or changing but will pickup speed as you drive


its a auto.gearbox break pads you got to replace them its going to be worse after a week your gearbox will not build up speed then and the car will heat up

May 25, 2011 | Isuzu Trooper Cars & Trucks

1 Answer

Reverse lights only work sometimes on isuzu wizzard


Manual gearbox: check on right hand side of gearbox. There's an electrical switch(looks like large nut nut) with 2 wires coming out of it These wires have connectors toward the top of the gearbox, diconnect them.
The wires that this switch was connected to, conect them to each other. ie the reverse light switch has been bypassed. Put the vehicle in reverse. Turn on the ignition. DO NOT START. Check the reverse lights. If on the switch is faulty and needs to be replaced. If not measure the voltage across each of the wires and a good earth point. (Gearbox casing will do fine. ) One of the wires should read < 12V.
If 12V then
  • Globes are faulty(Replace)
  • wiring to the globes are faulty - unlikely -(This can be repaired by simply running a new wire to the globes)
If no 12V then the wiring to the fusebox is faulty. A quick fix is to run a new wire from the fusebox to the switch(Connect to fuse C-3, indicated as "turn, back")

May 31, 2010 | 1998 Isuzu Trooper

1 Answer

How to bypass heater core on a 1995 isuzu


you need to remove the two hoses going into the firewall and plug them.They sell plugs and hose clamps at the parts house. Measure the hose size which is either going to be a 1/2' or 5/8" or 3/4"

Feb 22, 2010 | 1995 Isuzu Trooper

1 Answer

Location of reverse light switch on gearbox


on top section of gearbox near shifter the one closest to the rear of vehicle and it should have 2 red wires(one has trace colour) the blue/red switch is wrong one.both or all 3 switches look the same/similar. depending on engine config.

Feb 15, 2010 | 2001 Isuzu Trooper

Not finding what you are looking for?
1995 Isuzu Trooper Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...