Question about 2004 Chevrolet TrailBlazer

1 Answer

Is the Procedure for replacing Driver side Low Beam, same for Passanger side?.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 109 Answers

Remove Grill just by pulling (you may need to use screw driver on the ends on the headlights just be careful.) The you will see 2 tabs (See picture #1) on the back of the headlight just pull up. the assembly pulls out. Then the is a rubber cap over the bulb. Remove BulbIs the Procedure for replacing Driver side Low - 975f6a9.gif

Posted on Jun 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Driver side low and high beam on but dim. Passenger side low beam normal but high beam on and dim


I would check for the groundwire continuity

Driver side - dim low beams and no hi beam - Subaru Outback ...

www.subaruoutback.org > ... > General > Electrical & Electronics
Oct 11, 2014 - Hi everyone, My drivers side headlights are dim on low, (car has separate bulbs ... When the headlight switch is turned ON, but for low beams, ...

Driver-side Low beam Not Working (electrical issue not bulb ...

www.hummer4x4offroad.com/.../showthread.php?...Driver-side-Low-be...

Mar 12, 2015 - 10 posts - ‎4 authors
The high beam continues to work on both sides...I pulled the Driverside headlamp fuse and then both left and right beams lit up but very dim.

High beams ok, but not low beam - one side only - TDIClub Forums

forums.tdiclub.com > ... > VW MKIV-A4 TDIs (VE and PD)
Jan 23, 2014 - My driver's side lights are working fine - high and low beams. ... But it definitely looks like the big lamp on the driver's side gets brighter when ..... Drivers side headlight is very dim on low beam and goes out when on high beam ...

Dim driver's side headlight (low & high beam) - GrandAmGT.com Forum

www.grandamgt.com > ... > Technical Q&A

Dec 11, 2002 - 6 posts - ‎4 authors

Jan 04, 2016 | Cars & Trucks

4 Answers

I have a 2006 civic SI. DRL indicator is on, driver side low and high beam ok. Passenger side low beam ok but DRL and hi beam not working. Any help is appreciated.


When either the high or low beam light is out in either side, DRL (daytime running lights) indicator will come on. When one bulb goes out, that's a clue the opposite bulb will burn out soon, so its best to replace both bulbs. If it was a fuse issue, both left and right side would be out. If driver side is OK but passenger side is not, then its a bulb issue. A 2006 Honda civic takes 9006 (HB4) low beam bulbs and 9005 (HB3) high beam bulbs. Cheapest is online from Walmart site-2-store. After procuring, wear latex, vinyl, or ANY gloves to keep your (corrosive) oil skin from coming in contact with headlight glass bulbs. Your skin oil will chemically react and cause shorter life span on glass bulbs. Instruction don't tell you this, so you handle with your hands, then need to replace bulbs 3 years later instead of 5 years (or more) in the future. With gloves on, pop the hood and look behind each headlight. Turn counter clockwise to unlock headlight bulb holders. Its a quarter to half turn to unlock bulb holder lock. Replace one bulb at a time so you don't confuse high beam from low beam. The wire has a tab you need to lift to pull out & disconnect wire connector. You might need a slim narrow-**** (NOT phillips) screwdriver to lift the tab; or use your house key. Snap the wire connector to the new bulb, then twist into headlight housing to secure bulb holders, then move on to the next bulb to repeat the procedure. Pict below, 9005 high beam is on the left, 9006 low beam is on the right. Handle by grasping the plastic base, not the glass bulbs. The raised potrusion on the bottom center is where the tab locks onto wire connector. Replace all 4 bulbs now, but in the future, its likely the low beam will wear out before the high beam. In the future, replace only the pair, not all 4. The factory installs inferior bulbs that go out sooner, hoping you'll take to dealership and they ******** you with higher parts-n-labor fees. As opposed to Walmart online site-2-store, it would cost you AT LEAST triple in parts & labor from dealership to replace all 4 headlight bulbs :-(
45d1f6ac-2983-42b9-a46c-30ef441b89e7.jpg

Nov 29, 2013 | 2006 Honda Civic

1 Answer

Low Beam headlight not getting power? swiched blubs both worked on passanger side no so on driver side.


i had this same problem on passenger side low beam--trouble was wiring from headlamp back to underhood fuse box located at rear of battery.

Oct 26, 2011 | 2001 Buick Century

1 Answer

How do i replace the low beam headlamp on a 2008 mercedes?


Under the hood, there are two round head lamp covers on each side. One for high beam and one for low beams. The low beam is the outer cover. Turn this cover counter clockwise and remove. This will expose the back of the bulb. There is a small clip holding the bulb into the headlight housing, but you must unplug the light before removing clip. Once you have unplugged the light, the small metal clip can now be undone. on the side opposite the hinge, push the clip in towards the casing and then to one side (which way to push depends on which light it is.) Then the clip will release. you can now remove the bulb. place new bulb in and make sure it securely fits into position. reinstall the clip and reconnect the power. check for propeer function of the lamp before replaceing the cover. Once you confirm lamp is working replace cover and you are done.

This is easiest to see on the passanger side light. The driver side is slightly more cramped.

Jan 05, 2011 | 2008 Mercedes-Benz Mercedes Benz C Class

4 Answers

My low beam liht (driver side) does not work. High


the headlight itself will need replacing ...remove and replace by taking the old bulb out and re-installation is reverse procedure they should simply turn out

Oct 17, 2009 | 2006 Dodge Caliber

1 Answer

Driver side light


Replace the fuse for low beam under the hood right side in fuse box and or low beam bulbs

Dec 08, 2008 | 2005 Pontiac Aztek

1 Answer

Headlights on 1989 Nissan sunny


hi check your bulbs first but the problem is a bad ground or a faulty connecter look at the drivers side first clean all the grounds and connectors yates210456

Oct 12, 2008 | Nissan Z Cars & Trucks

Not finding what you are looking for?
2004 Chevrolet TrailBlazer Logo

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...