Question about 2002 Mitsubishi Montero

1 Answer

THE BACK DOOR ON MY MITSUBISHI WILL NOT OPEN IT IS A 2003 .I HAVE TRIED THE KEY AND THE REMOTE WITH NO LUCK

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had to disassemble the lock mechanism and lubricate the moving components. Access is through interior. Good luck!

Posted on Aug 02, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My mitusbishi 03 spyder alarm goes off every time I open my car door, how do I get it to stop?


Put the key in the door and hold it to the front for 15 seconds then hold it to the back for 15 seconds and it should reset.

Feb 20, 2015 | 2003 Mitsubishi Eclipse Spyder

1 Answer

2003 X tpye Jaguar driver's door will not open from outside -- handle appears to be disconnected- the remote opener stopped working several weeks ago -- key will lock all doors but driver's do


I had the same problem in my 2002 not isn't back I got a tin of wd 40 put the straw applecateter in the key hole and give it a good dose after 10 minute it open did it again now it works fine so I did them soon to make shore try it before you have to pull the door panel apart

Jan 12, 2013 | 2003 Jaguar X-Type

1 Answer

How to reset the alarm on a 2003 tahoe?


first replace the batteries in the remote . Also try manually locking the doors and use the key to open it .Sometimes that works. good luck

Nov 06, 2012 | 2003 Chevrolet Chevrolet Tahoe

1 Answer

Key less entry stopped working


poss low charge in battery in keys..... nearer you get lower the battery life.....

Feb 23, 2010 | 2003 Mitsubishi Lancer

1 Answer

Rear passenger doors on vw polo 2003 not working. cant open doors


Mine is doing the exact same.

Have two solutions, will try it later today:

1. Unlock with remote tnen lock with key and then unlock with key.
2. Might be a power problem, check that batery is good.

Dec 08, 2009 | 1992 Volkswagen Fox

1 Answer

The battery in my key fob for my 2004 Mitsubishi Diamante went flat. How do I reset it now that I have replaced the battery?


1-insert and remove key from ignition two times

2-close and open driver door two times

3-insert and remove key once from ign.

4-close and open drvr door twice

5-insert key into ign.,then close driver door

6-turn key to on (not start) then off, twice this is rewrite mode,have all remotes to reprogram it will clear any lost remotes.

7-remove key from ignition,the door locks should cycle twice.if not start over.it may take a few tries.

8-press lock/unlock together and hold for a second

9-release,and press lock on remote,the door locks will cycle confirming program.continue to do other remotes you have,steps 8 and 9.if only one in possession,you are done. To end mode open door or insert key into ignition.

You'll need to follow the steps with no more than a 1-2 second delay between each step.. hope it works

Aug 20, 2009 | Mitsubishi Diamante Cars & Trucks

3 Answers

Key for my Suzuki Aerio 2003


Don't buy it from the dealer, just buy a used remote from eBay. Use these instructions to program it.

1. Confirm that all doors are closed and the ignition key is out of the ignition cylinder.
2. Open the driver's door.
3. Within 10 seconds, Insert key into ignition turn to ON position and back to OFF and remove the key.
4. Within 20 seconds, close and open the drivers door 3 times. (Drivers door should be open)
5. Within 10 seconds, insert key into ignition turn to ON position and back to OFF and remove the key.
6. Press and hold both the LOCK and UNLOCK buttons together on the same remote for at least 5 seconds, the doors will lock and unlock (that's a very good sign)
7. Within 5 seconds, press the LOCK button on the same remote and release. You just programmed your remote ??
6_23_2017_2_42_10_am.jpg

Apr 22, 2009 | 2003 Suzuki Aerio

1 Answer

Programming keyless remote


2003-04 Mazda 6 REMOTE PROGRAMMING


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the driver’s door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the driver’s door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1 twice. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) twice. Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done!

Good Luck.

Jul 12, 2008 | 2003 Mazda Mazda6

Not finding what you are looking for?
2002 Mitsubishi Montero Logo

Related Topics:

205 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8547 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...