Question about 1991 Ford Mustang

2 Answers

How do you remove 92 mustang motor fan - 1991 Ford Mustang

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

There are like 6 bolts in the crank side of the fan shaft

Posted on Aug 01, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If you mean the cooling fan, leave the serpentine belt on and loosen 4 bolts at the pulley, then remove 2 bolts that hold on the fan shroud so that it can be lifted up a bit to give room for fan to come out as assembly( fan and fan clutch)

Posted on Jul 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My mustang 92 motor 2-3 it s getting motor oil into its intake manifold and hose but it doesnt neither fumes nor fails.what is causing this problem THANKS.


Check the PCV valve and replace it first before you tear into this, it could be bad. Might also be a leaking gasket. The PVC is the easiest and cheapest and is available at all auto parts stores.

Nov 26, 2010 | 1992 Ford Mustang

1 Answer

My coolin fan for my engine wont run? how do i fix it? 98 ford mustang gt


okay heres what causes not to kick in,
1 a bad motor
2 bad tempeture sensor
3 bad/defected fuse or relay.
check the fuses and your fan relay first. swap them around to test is every thing well then test the motor dirtectly, if its fine and works, then tempeture sensor on the engine. remove the harness and put a jumper wire on the prongs and what it kick the fan in. have the ign on with engine off for this. if it works replace the sensor.
hope this help you.

send mr your comments thansk

Aug 02, 2010 | 1998 Ford Mustang

1 Answer

How to change fan on 92 vw golf


It's best to remove the battery for enough room the remove the fan assembly. There are 4 10mm bolts holding the assembly to the radiator. Unplug the fan and disconnect anything held to the assembly. Remove the assembly, remove the clip holding the fan blade to the fan, remove the fan blade, unbolt the 3 10mm bolts that hold the fan to the assembly and remove the fan motor.

May 03, 2010 | 1992 Volkswagen Golf

1 Answer

How to change brake light on 92 mustang


open up your trunk and pull back carpet some cars you can grab the light harness and twist it and it will pull out then pull out bulb and replace the bulb but sum cars you will have to remove acouple bolts and pull out the whole taillight lens from outside the car then the rest is the same

Feb 22, 2010 | 1992 Ford Mustang

1 Answer

Safari 92 how can I get TO that heater fan?


you have to remove cowl vent grille.disconnect the transmission link from the crank arm on the motor by prying it toward the rear of the vechicle.remove the motor mounting bolts and remove the motor.then put new fan motor back in visa versa.

Nov 26, 2009 | GMC Safari Cars & Trucks

1 Answer

How do I replace heater/air fan motor in 2001 Ford Mustang


there is 3 bolts, a wireharness, and a black hose. Remove all these and pull out fan motor and the squirel cage.

Aug 01, 2009 | 2001 Ford Mustang

2 Answers

92 mustang reset switch electric fuel pump where located


on the mustangs i have the switch in just inside the rear hatch on the right side a yellow button you may have to remove a small cover to see it

Apr 27, 2009 | Ford Mustang Cars & Trucks

2 Answers

Have spark and gas in my 92 mustang lx but will not fire whats going on its a 4cy motor


well if memory serves me this car has a coil with a distributor so first replace the rotor button check the distributor cap for cracks and oxidation then check your timing belt remove #1 plug turn piston to tdc then check if your timing marks are lined up other things you could check:module,egr valve,pcv valve you could also be more specific how do you know it has spark and fuel?

Mar 29, 2009 | 1992 Ford Mustang

Not finding what you are looking for?
1991 Ford Mustang Logo

Related Topics:

231 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...