Mercedes benz c280 1995 door wont open - 1995 Mercedes-Benz C-Class

SOURCE: How to remove outside door handle and door lock of

take the door panel off and look for nuts to remove door handle.as for the lock it may be a u.clip.pull it down

SOURCE: Mercedes-Benz 320clk coupe 2002 with dead battery

Posotive can be found in hood driver side next to fuse box. It is a small rectangle box. You can hook negative to any solid ground on the car.

SOURCE: the interior door pull handle of my 2003 mercedes

Check with salvage yards first - you might be lucky!

SOURCE: how do you program a garage door opener on 2001

remote controls trasmit frequencies. I believe you hold your home remote control device within 2" to 5" of the car's remote control buttons. You select one button in the car which you wish to use as the garage access remote, and press it simultaniously with the home remote control button long enough for the blinking light to go on and blinks for 5 seconds. Then you are programmed. Test it to make sure it worked. If failed, try again. If it doesn't work, any Mercedes Dealership should do it for you FREE. Some of them now push for some money, but you tell them that you called Mercedes and based on your zip code they said you should go to this dealership and it will be done for FREE! They will take care of it immediately.

mx5turbo92

• 545 Answers
• Posted on Dec 17, 2009

SOURCE: i need the mercedes benz 1999 clk 430 radio code

AR82.60-P-7502-01A Coding Radio
(MODEL all with CODE (750) Radio Becker Europa 2000 with CODE (751) Radio Becker Grand Prix 2000 with RDS)

1. If the radio is disconnected from the power supply, it is not operational when re-connected. After switching on the ignition and the radio, the readout CODE appears in the display.
2. The code number for the radio is advised to you on the enclosed CODE CARD.
3. To enter the first digit of the code number, you have to continue pressing station button 1 until the correct digit appears in the display. Adopt the same procedure for the second, third and fourth digits.
4. Once you have entered the correct code number with the station buttons 1, 2, 3, 4 and confirmed the entry with the SEEK button (press down), the readout CODE disappears. The radio can now be operated.
5. If you enter a wrong code three times, you must wait 15 minutes before making a new entry. In addition, if 9 incorrect entries are made, the radio will then not operate for 24 hours. During this time the radio and the ignition (terminal 15) must remain switched on.

1. If the radio is disconnected from the power supply, it cannot be operated by simply reconnecting. After switching on the ignition and the radio the word "CODE" appears in the display on the radio.
2. The code number for the radio is given on the enclosed CODE CARD.
3. Enter the code number with the station button, e.g. number 1, station button 1. After entering the first number the word "CODE" disappears and the number entered appears followed by 4 dashes. The next character to be entered flashes. After entering all five numbers, the first character starts flashing again. In this state the code number can be written over as frequently as desired. A correction can be made only by entering the complete code number again.
4. Confirm code number: Press TUNE, AUTO/SEEK or SC button. The radio automatically switches on and indicates the radio station or frequency stored with station button 1.
5. If an incorrect code number is entered and confirmed, the word "CODE" appears again on the display. If an incorrect code is entered three times the word "WAIT" appears on the display and the radio locks up for approx. 10 min. If the code is entered incorrectly three times again the radio locks up again for 10 min. Three more incorrect entries (a total of 9 incorrect attempts) increase the lock-up time to 60 min. Another three incorrect entries lock up the radio for another 60 min. The waiting time runs only when the radio is switched on.