Question about 1999 Daewoo Nubira

1 Answer

How do i change the camshaft sensor on a 1999 daewoo nubira?

Do i have to take the timing belt out?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Read all of this before you begin! you may be able to skip a step that i couldnt !no.you dont have to remove the timing belt but check it. i did this to my nubira like two months ago. the belt felt loose but i didnt change it and now my car is on the side of the road) remove breather box. remove spark plug cover(top of engine two allen screws).see cam pos sen. wire clip at front of engine facing down, dont try to remove yet. clips are at the top sides of timing belt cover. from under the car remove plastic covers where you may find them on the pulley side and passenger side wheel well. using socket wrench relieve tension on torsion wheel(smallest pulley your s-belt crosses) by pushing up. release s-belt and remove(you may want to draw a quick diagram of how your belt is ran before removing). now remove the bolts from the timing belt cover.(when i did this i was also changing my harmonic balancer or crank pulley,if it is in the way of bolts remove the four bolts with a allen wrench,loosen it with the s-belt still on and car in fifth gear if standard to keep crank from turning. next place a long board or plank under the engine (across trans-housing,oil pan, as little on the oil pan as possible . place a jack at the center of the board and gently raise the engine. this relieves pressure from the top engine mount. remove the engine mount entirely. remove all screws from timing belt cover. remove cover. you will see two camshft gears at the top of the engine just below them you will see one star head screw(can usually be removed with an alle n wrench). it hold the cam pos sensor in place, remove then pull sensor out the top of the motor. sometimes they're a little bit stuck down in there. just pry a little but dont pull on wires! once removed disconnect wire replace, and rebuild. hope this helps

Posted on Jul 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change camshaft seal on a 2000 daewoo lanos


The OP asked how to replace the camshaft oil seal. The suggested answer talked about replacing the timing belt, which is part of the procedure, but not the seal. My auto parts store suggested a thorough cleaning with carb cleaner and then using high tack adhesive or gasket sealant to make sure the seal stays put. I would also like a rundown on R&R of the seal.

Jan 04, 2014 | 1999 Daewoo Nubira

1 Answer

Daewoo nubira 2002


Please follow this link to the see the whole process with diagrams of the belt change. Please note if the belt broke you likely have bent valves.

Oct 17, 2012 | 1999 Daewoo Nubira

1 Answer

WHAT IS CORRECT TIMING MARKS FOR TIMING BELT INSTALLATION. 2000 NUBIRA 2.0 DOHC AND CRNKSHAFT MARKS. Thanks Joe


TIMING BELT
Removal
Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing.
Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt.
Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle.
Support engine assembly from above with Support Fixture (J-28467-B). Remove engine mount bracket from timing belt end of engine.Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine).
Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 4 . Align camshaft sprocket timing marks with notches on valve cover. See Fig. 5 .
CAUTION: Engine damage could result if camshaft sprockets are not properly aligned with notches on valve cover.
Loosen the automatic tensioner bolt. Use an Allen wrench to rotate tensioner and relieve tension on timing belt. Remove timing belt.
Fig. 4: Aligning Crankshaft Sprocket Timing Mark
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim_4.jpg
Fig. 5: Aligning Camshaft Sprocket Timing Marks
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim2_3.jpg
Installation
Ensure crankshaft and camshaft timing marks are still aligned. Install the timing belt. See Fig. 7 . Turn the timing belt tensioner counterclockwise to tension the timing belt. Turn tensioner until the pointer aligns with the notch on the rear timing belt cover. Tighten automatic tensioner bolt to specification. See TORQUE SPECIFICATIONS .
Using crankshaft center bolt, turn crankshaft clockwise (as viewed from timing belt end of engine) 2 full revolutions. Ensure timing belt tensioner pointer is still aligned with notch.
If timing belt tensioner is correctly aligned, install timing belt cover. See Fig. 3 . Install the engine mount bracket on the timing belt end of engine. Position power steering hose in place, and install clamp bolt. Install crankshaft pulley. Install serpentine accessory drive belt.
Install right front splash shield. Install right front wheel. Install air filter housing and resonator. Connect air intake temperature sensor connector. Connect negative battery cable.
Fig. 7: Identifying Timing Belt Routing
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim3_1.jpg
here

http://www.2carpros.com/questions/daewoo-leganza-2000-daewoo-leganza-timing-marks

Feb 17, 2011 | 2000 Daewoo Nubira

3 Answers

Need cam torque specs


1999 to 2002 - 2.0L DOHC

Camshaft bearing cap bolts intake and exhaust.

N.m (INCH LBS)
8 ( 71 )

Jan 23, 2010 | 2001 Daewoo Nubira

2 Answers

2000 Daewoo Nubira camshaft position sensor


on the front under timing belt cover ,back cam ,if its not their then back of head about 3inches along from the gear wheel end

Sep 11, 2009 | 2002 Daewoo Nubira

1 Answer

How do i replace the camshaft sensor on a 1999 daewoo nubira? do i have to take the timing belt off?


no dont need to take belt off if its twin cam by the sound of things
just top bolt which is inside cam belt cover remove top cam cover retainer clip in top centre if still there and then 10mm bolt in cam belt cover just down from top middle section of cover bend gently to get to cam sensor bolt if have too much trouble doing this whole cam belt cover needs removing, air box, accessory drive belt and engine mount will need jack to support engine and to reinstall mount

Jun 27, 2009 | 1999 Daewoo Nubira

1 Answer

Where is the camshaft sensor located at on a 1999 daewoo nubira?


remove eng cover. it is at the front of eng neer timing belt, to re place timing belt must come off good luck

Jun 25, 2009 | 1999 Daewoo Nubira

1 Answer

Timing marks for a daewoo nubira cdx


Here is a pic if the timing marks two small marks on the cam pulleys and one small cut away on the crank pulley .
3d2c66e.png

Dec 14, 2008 | 1999 Daewoo Nubira

1 Answer

My daewoo lanos 2002 starts then cuts out almost straight away


change your camshaft sensor this is next to urbottom pulley

Aug 04, 2008 | 1999 Daewoo Nubira

Not finding what you are looking for?
1999 Daewoo Nubira Logo

292 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...