Question about 1999 Daewoo Nubira

1 Answer

How do i replace the camshaft sensor on a 1999 daewoo nubira? do i have to take the timing belt off?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Daewoo Master
  • 450 Answers

No dont need to take belt off if its twin cam by the sound of things
just top bolt which is inside cam belt cover remove top cam cover retainer clip in top centre if still there and then 10mm bolt in cam belt cover just down from top middle section of cover bend gently to get to cam sensor bolt if have too much trouble doing this whole cam belt cover needs removing, air box, accessory drive belt and engine mount will need jack to support engine and to reinstall mount

Posted on Jun 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change camshaft seal on a 2000 daewoo lanos


The OP asked how to replace the camshaft oil seal. The suggested answer talked about replacing the timing belt, which is part of the procedure, but not the seal. My auto parts store suggested a thorough cleaning with carb cleaner and then using high tack adhesive or gasket sealant to make sure the seal stays put. I would also like a rundown on R&R of the seal.

Jan 04, 2014 | 1999 Daewoo Nubira

1 Answer

WHAT IS CORRECT TIMING MARKS FOR TIMING BELT INSTALLATION. 2000 NUBIRA 2.0 DOHC AND CRNKSHAFT MARKS. Thanks Joe


TIMING BELT
Removal
Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing.
Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt.
Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle.
Support engine assembly from above with Support Fixture (J-28467-B). Remove engine mount bracket from timing belt end of engine.Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine).
Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 4 . Align camshaft sprocket timing marks with notches on valve cover. See Fig. 5 .
CAUTION: Engine damage could result if camshaft sprockets are not properly aligned with notches on valve cover.
Loosen the automatic tensioner bolt. Use an Allen wrench to rotate tensioner and relieve tension on timing belt. Remove timing belt.
Fig. 4: Aligning Crankshaft Sprocket Timing Mark
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim_4.jpg
Fig. 5: Aligning Camshaft Sprocket Timing Marks
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim2_3.jpg
Installation
Ensure crankshaft and camshaft timing marks are still aligned. Install the timing belt. See Fig. 7 . Turn the timing belt tensioner counterclockwise to tension the timing belt. Turn tensioner until the pointer aligns with the notch on the rear timing belt cover. Tighten automatic tensioner bolt to specification. See TORQUE SPECIFICATIONS .
Using crankshaft center bolt, turn crankshaft clockwise (as viewed from timing belt end of engine) 2 full revolutions. Ensure timing belt tensioner pointer is still aligned with notch.
If timing belt tensioner is correctly aligned, install timing belt cover. See Fig. 3 . Install the engine mount bracket on the timing belt end of engine. Position power steering hose in place, and install clamp bolt. Install crankshaft pulley. Install serpentine accessory drive belt.
Install right front splash shield. Install right front wheel. Install air filter housing and resonator. Connect air intake temperature sensor connector. Connect negative battery cable.
Fig. 7: Identifying Timing Belt Routing
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim3_1.jpg
here

http://www.2carpros.com/questions/daewoo-leganza-2000-daewoo-leganza-timing-marks

Feb 17, 2011 | 2000 Daewoo Nubira

1 Answer

I HAVE A 2001 DAEWOO NUBIRA THAT RUNS FINE MOST THE TIME BUT OTHER TIMES IT LOSES POWER AND STALLS.SOMETIMES IT WILL CRANK RIGHT BACK AND STALL WHEN I PUT IN GEAR AND START TO GO.OTHER TIMES YOU HAVE TO...


If I recall correctly there was a recall on the camshaft position sensor. In some cases it would melt.
MAKE: DAEWOO MODEL: NUBIRA YEAR: 2001 DEFECT SUMMARY:
ON CERTAIN PASSENGER VEHICLES, THE CAMSHAFT POSITION SENSOR MAY MELT RESULTING IN A BURNING SMELL AND VISIBLE SMOKE, WHICH MAY SUBSEQUENTLY LEAD TO THE MELTING OF THE CAMSHAFT COVER AND THE CAMSHAFT POSITION SENSOR WIRE HARNESS.
CONSEQUENCE SUMMARY:
THIS COULD POSSIBLY CAUSE AN UNDERHOOD FIRE.
CORRECTIVE SUMMARY:
DEALERS WILL REPLACE THE CAMSHAFT POSITION SENSORS AND INSTALL AN ADDITIONAL FUSE. THE RECALL BEGAN ON SEPTEMBER 7, 2004. OWNERS SHOULD CONTACT DAEWOO AT 1-877-362-1234, OPTION 6, OR FIND A LOCAL DEALER THROUGH THEIR WEBSITE AT WWW.DAEWOOUS.COM.

Sep 15, 2010 | 2001 Daewoo Nubira

3 Answers

Need cam torque specs


1999 to 2002 - 2.0L DOHC

Camshaft bearing cap bolts intake and exhaust.

N.m (INCH LBS)
8 ( 71 )

Jan 23, 2010 | 2001 Daewoo Nubira

2 Answers

2000 Daewoo Nubira camshaft position sensor


on the front under timing belt cover ,back cam ,if its not their then back of head about 3inches along from the gear wheel end

Sep 11, 2009 | 2002 Daewoo Nubira

1 Answer

Where is the camshaft sensor located at on a 1999 daewoo nubira?


remove eng cover. it is at the front of eng neer timing belt, to re place timing belt must come off good luck

Jun 25, 2009 | 1999 Daewoo Nubira

2 Answers

Looking for cambelt timing marks/ positions please, Twin cam engine Thanks Kevin


these bend valves if belt breaks while running
Align the timing marks on the camshaft gears to the notches on the camshaft cover, using the intake gear mark for the intake gear and the exhaust gear mark for the exhaust gear.
Align the mark on the crankshaft gear with the
notch at the bottom of the rear timing belt cover.

May 12, 2009 | 1999 Daewoo Nubira

1 Answer

Timing marks for a daewoo nubira cdx


Here is a pic if the timing marks two small marks on the cam pulleys and one small cut away on the crank pulley .
3d2c66e.png

Dec 14, 2008 | 1999 Daewoo Nubira

1 Answer

I have replaced broken timing belt on 1999 daewoo nubira and all timing marks line up but it will not idle properly and knocks


did the timing belt snapbefore you replaced it? if so you may have bent some valves. if not recheck timing marks and distributor position.

Jul 06, 2008 | 1999 Daewoo Nubira

Not finding what you are looking for?
1999 Daewoo Nubira Logo

202 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...