Question about 2005 Pontiac Grand Prix

1 Answer

How to reset theft deterrent system - 2005 Pontiac Grand Prix

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 145 Answers

Call a locksmith get your car key reprogram and your car will start again.

Posted on Jun 27, 2009

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 84 Answers

SOURCE: I want to permanently disable the theft deterrent

if you mean the low-jack system, leave it alone, i took one out, it went off and the cops showed up at my door

Posted on Nov 04, 2009

pippall
  • 1486 Answers

SOURCE: 2000 Kia Sportage Theft Deterrent System (Alarm)

replace the battery in the key

Posted on May 30, 2009

  • 318 Answers

SOURCE: theft deterrent system

Get the alarm removed.

Posted on Sep 25, 2009

Molson02536
  • 3854 Answers

SOURCE: Got a stuck key out of the ignition, but it

If the ignition lock has not been damaged, ( that's where the GM Passlock system reads the ignition key) here is how you reset the Passlock to youe keys.

Ignition keys relearn takes about 30 min to do. 30-Minute Learn Procedure 1. Turn ON the ignition, with the engine OFF. 2. Attempt to start the engine, then release the key to ON; the vehicle will not start. 3. Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF. 4. Turn OFF the ignition switch, and wait 5 seconds. 5. Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes. The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. 6. Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password. 7. With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles. Without a scan tool you may have momentary starter interruptions while history clears itself.

Good luck and keep me posted, be glad to know you got your car running again.

Posted on Nov 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Start 2003 pont. Grand prix without key


Without a key with anti-theft transponder inside your not starting anything . Your best bet call mobile lock smith . Anti-theft system ,software programmed into all module's involved in starting the vehicle .
The vehicle theft deterrent (VTD) system functions are provided by the theft deterrent control module. The VTD system prevents vehicle operation if a learned Passkey III (PK3) ignition key is not used to start the vehicle. Vehicles with steering column mounted ignition switches have the exciter integral with the theft deterrent control module which is located within the steering column. Vehicles with instrument panel mounted ignition switches have exciter modules separate from the theft deterrent control module with the vehicle wiring harness connecting the two. The PK3 key has a transponder embedded in the plastic head of the key. The exciter is an antenna which is made up of wire coils which surround the ignition lock cylinder. The PCM enables engine starting when it receives a learned fuel enable signal from the theft deterrent control module. The components of the VTD system are as follows:

Jan 09, 2017 | Cars & Trucks

1 Answer

Where is trsnreceiver in 99 cadillac sts


Anti-theft system transceiver ?
Theft Deterrent System
The Theft Deterrent System on this vehicle is comprised of two separate systems, the Personal Automotive Security System (PASS-Key?® III) and the Content Theft Deterrent (CTD) system. These system are described and diagnosed separately within this section. For CTD operation, refer to Content Theft Deterrent (CTD) Description .
SECURITY Indicator The yellow indicator SECURITY on the instrument cluster is controlled by both the PASS-Key?® III system (VTD module) and the CTD system (RIM).
?€¢
PASS-Key?® III system, the VTD commands the instrument cluster to control the indicator only when the ignition switch is ON.


?€¢
CTD system, the RIM commands the instrument cluster to control the indicator only when the ignition switch is OFF.
PASS-Key?® III System The PASS-Key?® III system is designed to help prevent vehicle theft by disabling the engine unless an ignition key with a specific electrical value is used in the ignition lock cylinder. The PASS-Key?® III system operates independently of the CTD system. Protection is provided even if the CTD system is not armed. The components of the system are the ignition keys (black or gray), ignition lock cylinder, Theft Deterrent (VTD) module, Reader Exciter, Powertrain Control Module (PCM) and two starter relays (START 1 and 2) in the underhood fuse block.

Oct 06, 2016 | 1999 Cadillac Seville STS

2 Answers

How to reset Theft Deterrent fuel enable signal


have you put obd11 scanner on it to find error code.
DTC P1626 Theft Deterrent Fuel Enable Signal Lost
Circuit Description
The Vehicle Theft Deterrent (VTD) system is incorporated within the body control module (BCM). The powertrain control module(PCM) monitors the state of health serial data message from the Theft Deterrent system to ensure that the PCM to BCM communications is established. If the PCM detects a loss of the state of health message while the engine is running, DTC P1626 will set. DTC P1626 can cause a no-start condition or normal operation depending on when the loss of Theft Deterrent system communication was detected. The engine will continue to start and run if the condition that set DTC P1626 occurred after the PCM received a valid theft deterrent password from the BCM and already allowed fuel during the ignition cycle. The engine will start and immediately stall if the condition that set DTC P1626 occurred before the PCM received a valid theft deterrent password. With this condition present, the PCM will inhibit fuel delivery and disable the starter until a valid theft deterrent password is detected. Refer to Content Theft Deterrent (CTD) Circuit Description .

Conditions for Running the DTC
The Theft Deterrent system has allowed fuel delivery.
Conditions for Setting the DTC
The PCM has detected a loss of the state of health serial data message from the Theft Deterrent system.

Action Taken When the DTC Sets
The PCM stores conditions which were present when the DTC set as Failure Records only. This information will not be stored as Freeze Frame Records.

Conditions for Clearing the MIL/DTC
The DTC becomes history when the conditions for setting the DTC are no longer present.
The history DTC clears after 40 malfunction free warm-up cycles.
The PCM receives a clear code command from the scan tool.
Diagnostic Aids,
An intermittent may be caused by:

• A poor connection

• Rubbed through wire insulation

• A wire broken inside the insulation

Check for the following conditions:, • Intermittent short circuit on the serial data circuit -- Refer to Data Link Communications Operation in Data Link Communications. Be sure to check all related wiring for an intermittent short to ground or short to voltage.

• Poor connection -- Inspect the wiring harness for damage. Check for an intermittent short or open circuit in the wiring harness related to the BCM, including the ignition, battery feed, ground, and Serial Data circuits.

Mar 13, 2016 | 2001 Buick Park Avenue

1 Answer

How am i supposed to get ride off the Service theft system?


It's hard to fix something if you don't know how it works ! Fixed ignition ? What did you fix or change ?
SERVICE THEFT SYSTEM
Security: Refer to Theft Systems Description and Operation in Theft Deterrent
You need to have it checked for trouble codes .
The theft deterrent system on this vehicle is comprised of two separate systems, the vehicle theft deterrent (VTD) system and the content theft deterrent (CTD) system. The VTD system prevents drive away theft by keeping the vehicle from starting. The CTD system is the vehicle alarm system which discourages unauthorized entry into the vehicle. These systems are described and diagnosed separately within this section.
Theft System Indicators
SECURITY The instrument panel cluster (IPC) illuminates the SECURITY indicator as determined by the vehicle theft deterrent (VTD) system and the content theft deterrent (CTD) system. The IPC receives a message from the theft deterrent control module or the rear integration module (RIM) via the serial data circuit requesting illumination.
?€¢
The VTD system requests the IPC to illuminate the indicator only when the ignition switch is ON. The VTD system uses the indicator as a malfunction indicator. For specific VTD condition that will illuminate the security indicator, refer to
Vehicle Theft Deterrent (VTD) Description and Operation .


?€¢
The CTD system requests the IPC to illuminate the indicator only when the ignition switch is OFF. The CTD system uses the indicator in order to identify system status. For specific CTD condition that will illuminate the security indicator, refer to Content Theft Deterrent (CTD) Description and Operation .


?€¢
The IPC performs the displays test at the start of each ignition cycle. The indicator illuminates for approximately 3 seconds.
SERVICE THEFT SYSTEM The radio illuminates the SERVICE THEFT SYSTEM message when the VTD system detects a failure. The radio receives a message from the theft deterrent control module via the serial data circuit requesting illumination.
This is one you need to take to the dealer , unless you have a GM factory scan tool !

Nov 21, 2015 | 2004 Cadillac CTS

1 Answer

Where is the alarm located on an 2006equinox


What alarm ? Anti-theft ?
The theft deterrent system on this vehicle is comprised of 2 separate systems, the Vehicle Theft Deterrent (VTD) System and the Content Theft Deterrent (CTD) System. The VTD prevents drive away theft by preventing the vehicle from starting. The CTD is the vehicle alarm system which discourages unauthorized entry into the vehicle. These systems are described and diagnosed separately within this section.
SECURITY Indicator
The SECURITY indicator on the instrument panel cluster (IPC) is controlled by the body control module (BCM) through the security indicator control circuit.
?€¢
The Vehicle Theft Deterrent (VTD) System contained in the BCM commands the instrument cluster to control the SECURITY indicator only when the ignition switch is ON. The VTD System uses the telltale as a malfunction indicator.


?€¢
The Content Theft Deterrent (CTD) System also contained in the BCM commands the instrument cluster to control the indicator only when the ignition switch is OFF. The CTD System uses the SECURITY indicator to identify system status.


It's software , a program inside the BCM ! An you can't just replace the BCM , it needs programming ! The dealer is the place to have that done ,most of the time ! If there is a SECRUITY light lit on the dash ,there is a DTC - diagnostic trouble code stored in the BCM , this code will point the service technician in the diagnostic path !

Oct 02, 2015 | Cars & Trucks

1 Answer

Changed steering column n won't atrt


Where is the ignition switch at , on the steering column ? Did you transfer the theft deterrent control module from the old column to the new one ? Do you have any lights lit on the dash , SECURITY ? Your car has a anti-theft system , the key has a transponder pellet imbedded in the head of it . Behind the plastic cover of the steering column ,around the ignition lock cylinder is the theft deterrent control module an antenna !
The vehicle theft deterrent (VTD) system functions are provided by the theft deterrent control module. The VTD system prevents vehicle operation if a valid (learned) transponder PASS-Key?®III (PK3) ignition key is not used to start the vehicle. The theft deterrent control module has an exciter that is part of the theft deterrent control module as an assembly. The PK3 key has a transponder embedded in the plastic head of the key. The exciter is an antenna which is made up of wire coils which surround the ignition lock cylinder. The PCM enables the engines starter and fuel delivery system when it receives a valid (learned) password from the theft deterrent control module via the class 2 serial data circuit. The components of the VTD system are as follows:

Apr 14, 2015 | 2002 Buick Rendezvous

1 Answer

I need to get passed the anti theft reset to get my 2000 cad.devlle.going, just bought it, I need help to locate fuse boxes, would like to trade somebody for a sharp running truck or car straight across,...


One is under the hood in the engine compartment an Rear Fuse Block
Left rear of the passenger compartment, under the rear seat ! There are a couple of fuse's , but they power up the ignition an the PCM ,so you can't pull those ! Beside that if the PCM does not get a fuel enable signal from the anti-theft module the vehicle won't start . You can't just disable thing's on this vehicle ! If you have security light on steady or flashing you need to take it to someone who has a diagnostic scan tool that can check DTC'S - diagnostic trouble codes ! A code reader can not access these type codes !
Vehicle Theft Deterrent (VTD)Circuit Description
(VTD) Theft Deterrent System Components
Ignition Key (Transponder) The ignition key for the (VTD) theft deterrent system is a typical ignition key with a transponder pellet located in the plastic end of the key. The ignition key transponder value is used to determine if a valid ignition key is being used to start the vehicle, there are approximately three trillion different transponder values available. This vehicle has two types of ignition keys.
?€¢
Master key (black plastic end) which can start the vehicle and lock/unlock all door locks, all storage compartments and the rear compartment lid lock.


?€¢
Valet key (gray plastic end) which can start the vehicle and unlock/lock all doors, but can not unlock/lock the storage compartments, or rear compartment lid lock.

Important: The transponder values are not readable and can not be serviced separately.
Theft Deterrent Module The theft deterrent module contains the software for controlling the VTD System. The theft deterrent module uses the following inputs and outputs to control the VTD system.
Inputs ?€¢
Battery voltage from the underhood fuse block PCM/BATT fuse, circuit 240 (ORN).


?€¢
Ignition start voltage from the ignition switch, circuit 1390 (WHT).


?€¢
Ground, circuit 450 (BLK).
Outputs Password exchange with the PCM (fuel enable), class 2 message circuit 1807 (PPL).
Powertrain Control Module (PCM) The PCM verifies that the passwords received from the theft deterrent module via the class 2 serial data line are valid. If a password is invalid the PCM disables the fuel delivery system. If the password is valid the PCM enables the fuel delivery system.
Starter Relay The starter relay is controlled by the PCM module via class 2 serial data (CKT 1807 PPL). If the theft deterrent module measures the correct transponder value, the PCM module switches the starter enable control (CKT 447 YEL) to ground. The relay is energized if the ignition switch is in the START position and the gear selector is in the PARK or NEUTRAL positions.

Mar 24, 2015 | Cars & Trucks

2 Answers

Where is the theft deterrent module located (VATS or anti-theft module) in GMC Acadia 2007?


the exact spot ,huh?

first off the FSM book and alldata.com has that, and vast more.

but you asked.

first off its many parts, why not post symptoms first then ask for Vats.

not the immoblizer but just theft

this is CDC system and is not VATS

the compenents are: as follows:

The content theft deterrent (CTD) system, when armed, is designed to deter vehicle content theft by pulsing the horns and exterior lamps for approximately 30 seconds when an unauthorized vehicle entry is detected. However, the CTD System does not affect engine starting.

An unauthorized entry can be any of the following with the CTD System armed:




  • When the liftgate or liftglass has been opened without the use of the keyless entry system or without first being unlocked.


  • When any door is opened without first being unlocked using the keyless entry transmitter.


  • When the driver door is opened without being first unlocked using the driver door cylinder.


The components of the system are:




  • The body control module


  • The door ajar switches


  • The driver door key cylinder switch


  • The liftgate/liftglass ajar switch


end quote.

more quotes under what to do first



Diagnostic Starting Point - Theft Deterrent
Diagnostic Starting Point - Theft Deterrent
Begin the system diagnosis with the Diagnostic System Check - Vehicle . The Diagnostic System Check will provide the following information:



  • The identification of the control modules which command the system


  • The ability of the control modules to communicate through the serial data circuit


  • The identification of any stored diagnostic trouble codes (DTCs) and their status


The use of the Diagnostic System Check will identify the correct procedure for diagnosing the system and where the procedure is located.



does this help, ????

May 10, 2014 | 2007 GMC Acadia

1 Answer

Why won't my 2003 cadillac cts start with the new theft deterrent module?


there is one wyre you can cut coming from the computer check itrenet taht will disable antitheft everything else will work properly that will let you no if it is the anti theft

Mar 30, 2013 | Cars & Trucks

1 Answer

Security button to resetm pass key is located where?


your vehicle is equipped with Personal Automotive Security System (PASS-Key II(R)).
This security system is designed to prevent vehicle theft by disabling fuel system and starter unless an ignition key with a specific electrical resistance is used in the ignition key lock cylinder. PASS-Key II(R) system operates using sensing contacts, which are located in the ignition key lock cylinder. These contact a resistor pellet located in the ignition key. When lock is rotated, battery voltage is applied through appropriate fuse and resistor pellet to theft deterrent module (except Century), or body control module (Century). Pellet resistance is then compared with programmed value in the theft deterrent module or Body Control Module (BCM).
System components include ignition key, ignition key lock cylinder, theft deterrent module (except Century) or BCM (Century), theft deterrent relay and Powertrain Control Module (PCM). The PASS-Key II(R) system can also be supplied as a special equipment option on some vehicles

It will reset itself after about 10 minutes. You just have to wait until you hear a click and the pass key light goes off.
Be sure to clean the little metal strip on your key while you're waiting...


Dec 05, 2010 | 1999 Chevrolet Lumina

Not finding what you are looking for?
2005 Pontiac Grand Prix Logo

Related Topics:

1,073 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...