Question about 2003 Lincoln Navigator

1 Answer

Location of oil pressure sender on '98 Linc. Navigator

Just trying to find the oil pressure sender (sensor) on my Navigator.

Many thanks...


Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

The oil pressure sending unit is usally located in the same side the oil filter is and this is because the oil filter is connected to the oil pump so there should be one little single wire in that area

Posted on Jul 03, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the fuel pressure sensor located on a 98 navigator

The fuel pressure regulator is on top of the drivers side fuel rail and has a vacuum line connected to it.

Mar 23, 2017 | 1998 Lincoln Navigator

2 Answers

Where is the oil pressure sensor on a 1995 Chevy Truck? V-8, 5.7 L. I have the new one, just can't find the one I need to replace.

If you go to a parts store, I prefer CARQUEST, they will gladly print up a schematic or just show you where it is if that is all you need.

Feb 01, 2016 | Cars & Trucks

1 Answer

96 Chevy blazer how do I get out of safe mode ran low on oil now runs an drives but won't let car go fast past 2000rpms

The computing system on your vehicle has no safe mode for running low on oil . The only thing that will happen is the check gauges light will come on.
The oil pressure gauge is an analog device that is located in the IPC. The oil pressure gauge is operated directly by the oil pressure sensor circuit. As the engine oil pressure changes, the resistance of the sensor and the current flow in the oil pressure gauge changes. The current flow in the oil pressure gauge causes the needle to move in order to appropriately display the engine oil pressure. A sensor resistance of 1ohms will display as 0 kPa (0 PSI) and a resistance of 88 ohms will display as 80 kPa (80 PSI ). The IPC also monitors the oil pressure sensor circuit and interprets the current flow in this circuit in order to determine when the engine oil pressure is too low. If the oil pressure is too low, the check gauges tell tale will turn on. The oil pressure sender is located on the left side of the 2.2L. The 4.3L engine, oil pressure sender is located at the top left side, near the distributor/high voltage switch.
Try disconnecting the battery cables an hold them together for ten minutes , reset ECM !

Nov 08, 2015 | Cars & Trucks

2 Answers

How can I check oil pressure guage is there a sensor or vacuume line that could of worked loose where would it be located at

Location of oil pressure sender unit depends on what engine you have. There should be one wire going to sender, and if it has come off, gauge will read zero. 4.0 inline 6 has sender low on passenger side of engine, above the starter.

May 06, 2015 | 1995 Jeep Grand Cherokee

1 Answer

Location of oil pressure switch 98 durango

please remember I am NOT there in front of you! my answers are based on your information the oil pressure sender is located in the rear of the engine on the passenger side next to the distributor you will need a special socket to install it without damaging it, it is called a deep oil pressure sender socket, here is a picture looking from the REAR of the engine,the only problem you may have is releasing the red slide lock it can be easy or difficult i clean the connector first then slide the red lock over and release the connector. Thanks John

I’m happy to assist further over the phone at

Mar 16, 2014 | Dodge Durango Cars & Trucks

2 Answers

Where is coolant temp sensor located

Not sure of your engine size so please pick the appropriate diagram:


Coolant temperature and oil pressure senders-4.3L engines


Coolant temperature and oil pressure senders-5.0L and 5.7L engines


Coolant temperature and oil pressure senders-7.4L engines


Coolant temperature and oil pressure senders-6.2L and 6.5L diesel engines

Sep 15, 2010 | 1994 GMC Sierra

3 Answers

Where is the oil pressure sending unit on my '98 chevy s10 blazer 4.3? and could you send me a pictures of where it is?

on the top left side of engine near the distributor/high voltage switch sorry dont have picture

Mar 30, 2010 | 2003 GMC Sonoma Extended Cab

2 Answers

Check oil level warning comes on. Oil level is OK. This warning is intermittent.

first thing is check the oil pressure not by the instrument panel if ok then panel is out if not its the sensor or oil pump Try this replace the temperature sender with the new green model and oil light will disappear no more three annoying beeps.

Dec 24, 2009 | 2000 Audi TT

2 Answers

98 ford explorer oil pressure sensor location

2.9L and 4.0L engines-Left side front of the engine, below the cylinder head in the engine block


Nov 28, 2009 | 1998 Ford Explorer

1 Answer

Oil pressure sender

It is located on the side of the oil pan, enclosed is a little more info on testing and installation.

See Figure 1
  1. Unplug sensor connector and insert a jumper wire between terminals 1 and 2.
  2. Start the vehicle.
  3. If the light is on, check the harness and dashboard light.
  4. If the light is off, replace the sensor and recheck the light operation.
0900c1528008c49c.jpgFig. 1: Connect a jumper wire between terminals 1 and 2REMOVAL & INSTALLATION
See Figures 2, 3 and 4
  1. Raise and safely support the vehicle.
  2. Unplug the connector from the sensor.
  3. Unfasten the sensor mounting bolts and remove the sensor from the oil pan.
To install:
  1. Install the sensor into the oil pan.
  2. Tighten the sensor mounting bolts.
  3. Plug in the sensor connector.
  4. Lower the vehicle.
0900c1528008c49d.jpgFig. 2: The oil pressure sensor is mounted to the side of the oil pan-850 model shown 0900c1528008c49e.jpgFig. 3: Unplug the connector from the oil pressure sensor 0900c1528008c49f.jpgFig. 4: Unfasten the retaining bolts and remove the sensor

Oct 01, 2008 | 1990 Volvo 740

Not finding what you are looking for?
2003 Lincoln Navigator Logo

503 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts


Level 3 Expert

80417 Answers


Level 3 Expert

5687 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides