Question about 2005 Chevrolet Equinox

2 Answers

ABS and Handbrake lamps on

Dear Sirs,

I have a yukon 2001 truck, its giving me ABS and brake lamp on and the brake is making vibrationas the ABS working when lamp come on and even in low speed.

I want to know what is the solution to stop that and make it work probably

thanks & regards

Qasem

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 82 Answers

This is usually caused by one of the front wheel speed sensors dropping signal under 10MPH. the first thing to try is to remove both front wheel speed sensors (Behind brake rotors) and clean the area where te sensor goes into the hole. Then lightly grease the sensor O ring and reinstall it.

Posted on Jun 28, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a GMC SAFARI 2005, its giving me ABS and brake lamp on and the brake is making vibrationas the ABS working when lamp come on and even in low speed.

Posted on Jun 19, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi,I have an Alfa 2001 156 cigarette lighter not working found some fuses near the battery but not one for the cigarette lighter


Fuse box in passenger compartment Alfa Romeo 156.
fuse box location.
The fuses for the main devices are housed in a control unit under the dashboard, to the left of the steering column. To gain access to them, remove the panel (A) releasing the tabs (B) in the direction of the arrow below and remove the screw (C).

fuse box layout.

1 Ignition auxiliary circuits relay 1 2 Heated rear window relay 3 Horn relay F1 (10A) RH headlamp- high beam F2 (10A) Headlamp high beam warning lamp, LH headlamp-high beam F3 (20A) Boot lid/tailgate lamp, central locking F4 (10A) Headlamp adjustment, RH headlamp-low beam F5 (30A) Electric windows(front) F6 (10A) LH stop lamp, LH tail lamp, RH licence plate lamp, RH rear fog lamp, RH side lamp F7 (10A) LH licence plate lamp, LH rear fog lamp, LH side lamp, RH stop lamp, RH tail lamp F8 (10A) LH head lamp-low beam F9 (15A) Cigarette lighter, heater/air conditioning (AC) F10 (20A) Wind screen wash/wipe system F11 (20A) Horn F12 (10A) Alarm system, anti-lock brake system (ABS)(with ESP), audio system, instrument panel, interior lamps F13 (10A) Anti-lock brake system (ABS), central locking, electric door mirrors, electric windows, glove box lamp, reversing lamps, stop lamp (high level) F14 (10A) Hazard warning lamps F15 (30A) Door mirror heater, heated rear window

Sep 13, 2017 | Alfa Romeo Cars & Trucks

1 Answer

I have a 2007 yukon denali xl, I got my front brakes and right wheel hub changed. When he got doney brake lights in the back of the truck wI'll not shut off. Brake light switch did nothing to help..


Who put the front brakes an wheel hub bearing on the vehicle ? A qualified repair shop ? A friend ? The front brakes an wheel hub would have nothing to do with the brake lights . An the brake light switch is an input to the BCM - body control module .
Stop Lamps
When the driver presses the brake pedal, the switch contacts open and battery positive voltage is interrupted to the BCM. The BCM then supplies voltage to both the turn/stop lamp supply voltage circuit and trailer rear turn/stop lamp supply voltage circuits. The BCM also supplies voltage to the CHMSL though a dedicated circuit.
I suggest you take it back to who did the front brakes , or a quailfied repair shop .
DTC B3445 00: Stop Lamp Circuit - DO you know what a DTC is ? diagnostic trouble code !
Diagnostic Fault Information
Circuit
Short to Ground
Open/High Resistance
Short to Voltage
Signal Performance
Stop Lamp Supply Voltage
B3445 00
--
Stop Lamps Inoperative
Stop Lamps Always On
Circuit/System Testing
Disconnect the stop lamps and test the individual stop lamp assemblies for internal shorts between all terminals.
? If a short between terminals is found, replace the stop lamp socket or circuit board as applicable.
Test the stop lamp supply voltage circuit for a short to ground.
? If all circuits/connections test normal, replace the BCM.

Nov 09, 2016 | 2007 GMC Yukon XL Denali

1 Answer

Engine Code B0281


there is no B0281 only a c0281 and that is your abs is malfunctioning because of the brake lamp switch. check connection on switch if it is fine you need a new switch

Mar 15, 2013 | 2001 GMC Yukon

1 Answer

Hand brake lamp on instrument panel


The light is not only used to indicate that the parking brake is on, but also indicates that there is a problem with the braking system. Make sure your brake fluid is topped off.

Jun 27, 2012 | 2001 GMC Yukon XL

1 Answer

The abs and parking brake idiot lights turn on and off intermittently, i've been told its possibly the ABS sensor


Sounds like a "WSS" (wheel speed sensor) problem. Each wheel has one. Located on the backside of each hub, between the brake disc and hub bearing. Check for loose connector first. Wire damage? Wiring touching exhaust pipes or rubbing wheel or tire? Look for mud or debris or damage to the sensor's or the rotating sensor ring. ( has a lot of "teeth") Try driving in reverse, in a straight line 25 to 30 feet, then drive forward twice that distance. If that does not clear the warning lamps most auto parts stores can hook into your computer (usually for free) and determine which sensor(s) have an issue. Replacing these sensors is common and simple.

Aug 23, 2011 | 2001 GMC Yukon

1 Answer

1993 GMC K3500. Anyone know where i can find an ABS (antilock brake system) wiring diagram? When i bought my truck, it came without the ABS computer. I recently aquired the computer but still dont get...


You can find free wiring diagrams here http://www.bbbind.com/free_tsb.html Enter vehicle info. Year , make , model an engine size . Under system click on brakes .under subsystem brake control will show on it's own . Click the search button .

Apr 01, 2017 | GMC K3500 Cars & Trucks

3 Answers

Gmc yukon has the abs & parking brake light


you have to fix the problem with ur brakes- first check the wiring ,connectors and connection clips to the abs sensors and modulator if looks ok than have truck scanned some auto stores such as auto zone / advanced auto do it for free the code will give u a start point towards fixing ur problem--visual inspection of brakes doesnt always show problem

Nov 26, 2009 | 2001 GMC Yukon Denali

1 Answer

Abs lamp; brake both on????


YES THEY ARE BOTH ON HOW CAN I FIX IT MY SELF.

Sep 30, 2009 | 2001 Ford Windstar

2 Answers

NEED TO CHANGE BULB BUT CAN'T SEEM TO FIGURE OUT HOW TO GET INTO CASING


First open the rear liftgate (not just the glass). This will expose the two screws that secure the housing of the lamp to the body (it also exposes the connector plug which, obviously, you should unplug). After removing the two screws, separate the rubber housing from the LED lamp itself....and there you have it!
The third brake light might be a sealed lamp, so the entire brake light must be changed. you can't just replace the bulbs.
I hope this helps.

May 21, 2009 | 2001 GMC Yukon XL

1 Answer

No brake lights on 96 yukon


The brake fuse #1 is located inside the truck below the steering column. I am assuming you have verified there is 12v power at the fuse & thru the brake lamp switch (orange wire power in & white wire power out, when pedal depressed) at all times. After the brake lamp switch , power goes (white wire) to the Turn signal/hazard lamp switch & out (dark green wire-rt brake lamp & yellow left brake lamp)

Feb 16, 2009 | 1999 GMC Yukon

Not finding what you are looking for?
2005 Chevrolet Equinox Logo

199 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6910 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...