Question about 1989 Nissan Maxima

1 Answer

The temperature slider is stuck in the hot position. How do I get the control unit out of the dash

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 25 Answers

Remove outer panel, usually two screws above and snap clips below. When it's out of the way, the gauge cluster should be easily removed by then- usually two screws on either side, just check for other screws to make sure. You will need to pull out the wiring sockets behind the gauge cluster (this could be a tight reach). Once it has been freed, you can remove the transparent cover. Hope this helps.

Posted on Jun 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

2004 Cadillac DeVille hot air blows out of passenger and rear vents when air condition is running


Does adjusting the passenger side temperature control on the dash have any effect?

Mar 29, 2015 | 2004 Cadillac Deville

1 Answer

Heater and ac controlls not working 1994 corvette


Are all the vents working? Does your Cruise Control work (properly) it may work and shut off. If your vents are working is only hot air or cold air coming thru, or just your defroster vent?

You have a 3 way check valve under fuel rail guard on passengers side, its a pastic barrel shape thing it rots and creates holes in it causing your ac vents and cruise control to malfunction.

next your heater control unit if you have the one with a slider to regulate the hot or cold temperature breaks easily inside unit, its only plastic. Its an arm inside unit to control the temp in car it slides a door open or closed for heat. If you look where he slider enters thru that hole space you will see a post it sits on to open and close .

Nov 20, 2012 | 1994 Chevrolet Corvette

2 Answers

Heat not very hot


Possibly the thermostat is bad or stuck open, not allowing the engine to get hot enough. A plugged heater core can also cause poor heat.

Mar 09, 2010 | 2000 Jeep Grand Cherokee

2 Answers

Ford ka 2005 heater fault


There is a vacuum operated actuator that is in the venting system When you switch your control knob, a vaccum pressure is applied to this actuator. Then the actuator moves a flap that controls the warm air/cold air flow. The flap can get stuck, or the actuator can become leaky or weak

Jul 21, 2009 | 1999 Ford Taurus

2 Answers

All i get from my heater is heat i cant turn the ac on, and when i turn off the heater it still blows hot air


Sounds like a stuck heater core valve. Find heater core valve. Under hood, find the two heater core hoses going into firewall. One of the hoses has a valve. Operate temperature control (full heat, then full cold) check that valve changes position. If not either replace valve or control system failure. Also, when temperature control in cold position, one hose should feel hot and the other cold. Temp fix: disable valve to close no heat or on heat.

Jul 10, 2009 | 1998 Dodge Ram 1500 4WD

1 Answer

My temperature control is stuck on heat...no


Go to an autoparts store and see if they carry a temperature control valve. When you see it you can find out if it has a cable or vacuum control to operate it. Then you can have someone move the dash controls and see if anything moves under the hood. If it is a cable and does not move the cable is broke or unhooked under the dash. If it is vacuum controlled a vacuum line is wrong and keeping the valve open.

Jun 09, 2009 | 1998 Ford Explorer

1 Answer

HOT AIR ALWAYS


this problem is almost always caused by the air temperature control blend door being warped and stuck or by the electric actuator that moves it, the common issue is the blend door actuator. To replace or repair this part requires the removal of the entire dash assembly.

Apr 08, 2009 | 1998 Ford Explorer

1 Answer

95 Lincoln towncar stuck on high temperature setting


u need a new blend door motor. this is a job 4 the machanic cause the whole dash must be pulled back

Mar 25, 2009 | 1995 Lincoln Town Car

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...