2007 town and country fans won't run - 2007 Chrysler Town & Country LX New Cars

6ya staff

• 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

6ya - Get Instant Help

6ya.com

Need repair answers fast Use 6ya to...

Posted on Jan 02, 2017

mike ryner

• 115 Answers

SOURCE: low speed fan relay for the 2005 chrysler town and country

If you are talking about the cooling fan relay for the radiator there is no low speed and high speed relay. There is only one relay and it is behind the grill revitted to the bumper rail. It is doesnt look like you typical relay.

Posted on Mar 08, 2009

Ronald Mueller

• 1263 Answers

SOURCE: radiator fan relay,2001 chrysler town country

the relay is located in the power distribution box under the hood the relay will be a square black or gray cube just pull out and make sure you rerplace it with the same type relay. refer to your owners manual for any questions regarding the fuses and relays

Posted on May 08, 2009

SOURCE: 2007 Chrysler TOWN AND COUNTRY.. OVRHEAD MAP

I had the same problem on my 07 and it turned out to be caused by the bulbs getting too hot and melting the surrounding plastic which opened the circuit powering them. I was able to fix the problem by removing the bulbs and cleaning the sockets allowing the bulbs to seat correctly. The lenses snap off to give you access to the bulbs. If you are not familiar with how interiors of cars come apart, I would not suggest doing it as you may crack the lens.

Posted on Oct 13, 2009

SOURCE: How to change a starter in a 2007 town and

1. Disconnect the negative side of battery. 10mm ratchet.
2. Jack the front of the vehicle.
3. Use jack stands to support the vehicle. Do not use only the jack. I use the jack as a back up for the stands.
4. Chock/Block the rear wheels.
5. The Starter is located on the front side of the engine, just below the exhaust manifold near the transmission-flywheel housing.
6. Looking at the engine compartment from the left fender side of the van, there are two bolts (15mm) that need to be removed. One located at 10-11 o'clock position on the Starter and one at 4-5 o'clock position on the Starter.
7. The Upper Bolt is easily accessed from the front of the vehicle going OVER the radiator. It is partially hidden by a black brace. There is a black ground wire going to where a nut is located. This first nut will allow you to take off the ground connection, however the bolt has another nut further in (to the left) which is totally hidden. Remove this first nut.
8. After the first nut is off then using a deep socket 15mm socket remove the second nut which is attached to the bolt.
9. Go under the vehicle to remove the wires from the Starter. The first wire is the positive cable (should be red) attached on the solenoid portion of the starter. That is a 13mm nut, Remove the nut and lock washer and detatch the wire. The second wire (single small gauge) goes to the solenoid and is connected using a slide lock - press release connection. It is difficult to see the slide lock and the press release located on the top side of the connection. Slide the red slide lock out and press the release, and pull out the connection straight out. Do not force it, or it may damage the connector. Note the placement of the bottom bolt position on the Starter. DO NOT remove the tow (2) small, but long connector bolts on the wire connection end of the starter.
10. Remembering the noted postion: remove the lower 15mm bolt from the Starter. The bolt head is located on the back side of plate moving towards the left side of the Van. It is easily accessed from underneath in front of the transmission. Near the end of removing this bolt, support the starter or it will fall out.
11. Remove the Starter, noting the position of the starter. There should be a separate starter facing plate. If if didn't come down with the starter check up in the starter to flywheel opening and remove the plate.
12. Installation is Reverse of above. The facing plate is a little tricky getting it to stay in place. By starting with the bottom bolt it is easier, Make sure you continuously support the Starter in position to save crossthreading the bolt or starter. Hand tighten only the bottom bolt as youwnat to be able to turn the starter slightly to get the top bolt in.
Starter Bolts are tigthen to 35 ft-lbs.
I hope this helped. Let me know if it helped or if you need additional help. Happy Thanksgiving!!

Posted on Nov 26, 2009

SOURCE: I have a 2007 Chrysler Town and Country overhead mamap lite

I very gently pried on the outer curve of the clear cover. It snapped out easily. Then I noticed it only clips in to place on the left and right side of the widest part of the cover. I was then able to simply twist the bulbs out socket and all.

Posted on Dec 19, 2009