Question about 1993 Buick Park Avenue

1 Answer

Need step by step directions on oil pan removal

Its a 1985 ford f150

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 65 Answers

Since that would be several pages in the internet and words are always the best go and buy a shop manual for thirty bucks (eiter haynes or Clymer) the will pay for itself in a few months and if you plan on keeping the truck you'll use it over and over. plus it has pictures showing important things specific to that vehicle that you may miss other wise

Posted on Jun 27, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers


Drain oil then raise car on jackstands. Jacks alone will fall. Unbolt pan n clean any dirt in it. Put newgasket on and rebolt

Apr 09, 2018 | Ford Cars & Trucks

1 Answer

How do i change the oil pan on a 2007 ford f150 4.2L v6?

4.2L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
    During engine repair procedures, cleanliness is extremely important. Any foreign material, including any material created while cleaning gasket surfaces, that enters the oil passages, coolant passages or the oil pan can cause engine failure.
  2. Raise and safely support the vehicle.
  3. Remove the starter.
  4. Drain the engine oil. Install the drain plug when finished.
  5. Remove the 4 bolts and the crossmember.
  6. Remove the 3 oil pan-to-transmission bolts.
  7. Remove the 17 bolts and the oil pan.
  8. Remove and discard the oil pan rear seal.
To install:

Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means to clean the sealing surfaces. These tools cause scratches and gouges which make leak paths. Use silicone gasket remover and a plastic scraping tool to remove all traces of old sealant. Follow the directions on the packaging.
  1. Clean the gasket mating surfaces using silicone gasket remover, a plastic scraping tool and metal surface prep. Follow the directions on the packaging.
    If the oil pan is not secured within 4 minutes, the sealant must be removed and the sealing areas cleaned. To clean the sealing area, use silicone gasket remover and metal surface prep. Follow the directions on the packaging. Failure to follow this procedure can cause future oil leakage.
  2. Apply silicone gasket and sealant to the oil pan sealing areas shown and install the oil pan rear seal.
  3. Apply silicone gasket and sealant to the rear main bearing cap.
  4. Install the oil pan rear seal.
  5. Apply a bead of silicone gasket and sealant to the oil pan mating surface.
  6. Position the oil pan and install the bolts. Tighten the bolts in the sequence shown. Tighten to 10 Nm (89 inch lbs.).
  7. Install the 3 oil pan-to-transmission bolts. Tighten to 34 Nm (25 ft. lbs).
  8. Install the starter.
  9. Position the crossmember and install the 4 bolts. Tighten to 90 Nm (66 ft. lbs.).


Feb 15, 2016 | Ford Cars & Trucks

1 Answer

Change the oil pump in a f-150 4.6 2002 model

Ford F150 5.4L Timing Chains and Guides Oil Pan Oil Pump ...

? 5:08
May 10, 2014 - Uploaded by dezertol
Ford F150 5.4L Timing Chains and Guides, Oil Pan, Oil Pump, Cam ... i am looking into changing the oil pump myself... did you try removing the intake ... I need help with my timing for i 3v4.6 mustang gt, im about to take of my ...

Ford 4.6L, 5.4L, 6.8L Engines -Melling Oil Pumps - YouTube

Nov 04, 2015 | Cars & Trucks

1 Answer

How do i removal the oil pan from a 1985 4.9L Ford 150?

you mite have to remove the motor mounts so that you can pick up on motor just a little.. a couple of inch.. then take off the oil pan bolts

Oct 30, 2013 | 1985 Ford F150

1 Answer

How do you replace a oil pan on a 1985 Ford Tempo Do you have to remove engine?

u should not have to remove pan. if the seal is leaking just replace. when u loosen the bolts it will provide enough room to replace gasket.
if you really have to replace the pan. you have to loosen the motor mounts and jack up the engine a little. be very careful!!!!

Jul 03, 2012 | 1985 Ford Tempo

1 Answer

Directions to change fuel pump on 1985 Ford f150 5.8

disconnect battery remove truck bed follow the fuel line to the pump unplug wires take off pump ring change pump and filter go in reverse of these directions hope this helps

May 06, 2010 | 1985 Ford F150

2 Answers

Can i drop the oil pan and or change the oil pump with out pulling the engine?

Bearings are located at each "big end" of every connecting rod (the rod that connects each piston to the crankshaft and at each crank support (part of the engine block) To measure wear on a bearing you need something called "plastigage" which is placed betweenthe bearing surface and the crank, the cap re-torqued then removed. You then measure the spread of the gauge material with a micrometer. If you remove any bearing and see brass backing instead of bearing material, you don't need to measure it...It is gone.You need to check all the bearings in this manner. If any Main bearings are worn, the engine needs to be removed as that is the ONLY correct way to replace them without having another immediate failure.
I'm not saying this to be insulting, but if you need to ask where the bearings are, it is likely you should not be doing this work. Though it appears to be a "take out, put in" operation, it takes experience and skill not only to do the job correctly but to recognize things inside that can bite you in the **** if they are not taken care of.
One other item....If you don't understand this answer do not rate it.
I only am a beginner (40 years in repair, many spent building 7,000 hp race engines) so, I'm not very sure about the answer (if you believe that, monkeys will fly tomorrow!!!) We do this free and really don't need a poor rating for a perfectly good answer!!!
Good luck!

Mar 15, 2010 | 1991 Ford F150

1 Answer

How do I raise the 96 ford f150 truck to repair the oil pan

get a set of ramps to drive up on, or a bigger floor jack. ramps are the easiest.

Nov 27, 2008 | 1996 Ford F150 Regular Cab

1 Answer

Oil pump do I jack the engine up or will it clear in the v6

if you have to raise the engine to remove the oil pan then you will be able to get at the oil pump it only two bolts once you have the pan off and yes its a real pain

Jun 30, 2008 | 1985 Ford F150

Not finding what you are looking for?
1993 Buick Park Avenue Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts


Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides