Question about 2004 Toyota Sequoia

1 Answer

Bolt torque for 2004 camshaft and crankshaft gear

Bolt torque for 2004 Toyota Sequoia 4.7L camshaft and crankshaft timing gear bolt.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 104 Answers

If your installing your crankshaft the Torque: 27 N·m (275 kgf·cm, 20 ft·lbf). And for your camshaft the 25mm bolts [2] are 7.5 N·m (80 kgf·cm, 69 in.·lbf) and the rest are 16 N·m (160 kgf·cm, 12 ft·lbf)

Posted on Jun 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Need timing gear marks for 2004 Kia Sadona 3.5L engine



Removal & Installation

3.5L Engine

  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Record the radio anti theft code data.
  3. Remove or disconnect the following:

    Negative battery cable Engine cover Accessory drive belts Idler pulley Crankshaft pulley Power steering pump pulley Belt tensioner pulley Upper and lower timing belt covers
  4. Support the engine with a floor jack and remove the engine mount.
  5. Rotate the engine to align the camshaft sprocket timing marks with the cylinder head cover timing marks.

    0996b43f8022cb71.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt routing and timing marks-3.5L Engine

  6. Remove or disconnect the following:

    Auto tensioner Timing belt

    0996b43f8022cb72.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt and related components-3.5L Engine


To install:
  1. Ensure that the engine is set to Top Dead Center (TDC).
  2. Prepare the auto tensioner for installation by compressing it in a vise and installing a retaining pin.
  3. Install the timing belt in the following order:
    1. Crankshaft sprocket
    2. Idler pulley
    3. Left bank exhaust camshaft sprocket
    4. Left bank intake camshaft sprocket
    5. Water pump pulley
    6. Right bank intake camshaft sprocket
    7. Right bank exhaust camshaft sprocket
    8. Tensioner pulley

  4. Install the auto tensioner. Do not remove the retaining pin at this time.
  5. Check that the crankshaft and camshaft timing marks are aligned correctly.
  6. Rotate the crankshaft 1 / 4 turn Counterclockwise .
  7. Rotate the crankshaft 1 / 4 turn Clockwise to return the engine to TDC.
  8. Loosen the tensioner pulley center bolt.
  9. Apply 44 inch lbs. (5 Nm) torque to the tensioner pulley as shown and tighten the center bolt to 32-41 ft. lbs. (43-55 Nm).

    0996b43f8022cb73.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Adjusting the tensioner pulley-3.5L Engine

  10. Remove the auto tensioner retaining pin.
  11. Rotate the crankshaft 2 revolutions Clockwise , then wait 5 minutes for the auto tensioner to adjust.
  12. Measure the auto tensioner rod as shown. If the measurement is not 3.8-4.5 mm, then repeat the belt tensioning procedure.

    0996b43f8022cb74.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Measuring the auto tensioner rod-3.5L Engine

  13. When the auto tensioner measurement is correct, install or connect the following:

    Engine mount Upper and lower timing belt covers Belt tensioner pulley Power steering pump pulley Crankshaft pulley Idler pulley Accessory drive belts Engine cover Negative battery cable
  14. Reprogram the radio anti theft codes.

    Kia_Sedona_2002-2006
    Timing Chain, Sprockets, Front Cover & Seal

    Print


    Removal & Installation

    3.8L Engine

    1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
    2. Record the radio anti theft code data.
    3. Remove the engine from the vehicle.
    4. Remove the drive belt. Remove the power steering pump. Remove the air conditioning compressor.
    5. Remove the alternator. Remove the drive belt idler. Remove the drive belt tensioner. Remove the water pump pulley. Remove the intake manifold.
    6. Remove the connector bracket from the left cylinder head cover. Disconnect the right ignition coil connector, condenser connector and remove the bracket.
    7. Remove the left cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
    8. Remove the right cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
    9. Set the No. 1 cylinder to TDC on the compression stroke. Turn the crankshaft pulley and align its groove with the timing mark T of the lower timing chain cover.
    10. Check that the mark of the camshaft timing sprockets are in straight line positioning on the cylinder head surface. If not rotate the crankshaft 360 degrees. Do not rotate the engine counterclockwise.
    11. Remove the oil pan. Remove the crankshaft damper pulley. Remove the timing chain cover.
      NOTE Be careful not to damage the contact surfaces of the cylinder block, cylinder head and timing chain cover. Before removing the timing chain, mark the right and left timing chains with an identification mark based on the location of the sprocket because the identification mark on the chain for TDC can be erased.
    12. After compressing the timing chain tensioner, install a set pin. Remove the right cam to cam guide. Remove the right timing chain auto tensioner and timing chain tensioner arm.
    13. Remove the oil pump chain cover. Remove the oil pump chain tensioner assembly. Remove the oil pump chain guide. Remove the right timing chain.
    14. Remove the right timing chain guide. Remove the oil pump chain sprocket and oil pump chain. Remove the crankshaft sprocket, oil pump and camshaft drive gear.
    15. Remove the left cam to cam guide. Remove the left timing chain auto tensioner and timing chain tensioner arm. Remove the left timing chain.
    16. Remove the left timing chain guide. Remove the crankshaft sprocket and left camshaft drive. Remove the tensioner adapter assembly.

      0996b43f8020193b.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing chain and related components-3.8L Engine


    To install:
    1. Check the camshaft and crankshaft sprockets for wear and damage, replace as required.
    2. Inspect the tensioner arm and chain guide for wear and damage, replace as required.
    3. Check that the tensioner pin moves smoothly when the ratchet pawl is released with a thin rod.
    4. The key of the crankshaft should be aligned with the timing mark of the timing chain cover. This indicates that the piston is at TDC on the compression stroke.
    5. Install the tensioner adapter assembly. Install the crankshaft sprocket and left camshaft drive.
    6. Install the left timing chain guide and torque the retaining bolts 14-18 ft. lbs.
    7. Install the left timing chain. Be sure to install the chain with no slack between the camshaft and the crankshaft (crankshaft sprocket, timing chain guide, exhaust camshaft sprocket, intake camshaft sprocket). The timing mark of each sprocket should be matched with the timing mark (color ink) of the timing chain at installation of the timing chain.

      0996b43f80201924.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Left timing chain markings and installation: (D) exhaust camshaft sprocket (C) intake camshaft sprocket-3.8L Engine

    8. Install the left timing chain tensioner arm and torque the retaining bolts 14-16 ft. lbs.
    9. Install the left timing chain tensioner and torque the retaining bolts 7-9 ft. lbs.
    10. Install the left cam to cam guide and torque the retaining bolts 7-9 ft. lbs.
    11. Install the crankshaft sprocket, oil pump and right camshaft drive.
    12. Install the oil pump chain and oil pump sprocket. Torque the retaining bolt to 14-16 ft. lbs.
    13. Install the right timing chain guide. Torque the retaining bolts to 14-18 ft. lbs.
    14. Install the right timing chain. Be sure to install the chain with no slack between the camshaft and the crankshaft (crankshaft sprocket, intake camshaft sprocket, exhaust camshaft sprocket). The timing mark of each sprocket should be matched with the timing mark (color ink) of the timing chain at installation of the timing chain.

      0996b43f80201925.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Right timing chain markings and installation: (C) exhaust camshaft sprocket (B) intake camshaft sprocket-3.8L Engine

    15. Install the right timing chain tensioner arm. Torque the retaining bolts to 14-17 ft. lbs.
    16. Install the right timing chain auto tensioner. Torque the retaining bolts to 7-9 ft. lbs.
    17. Install the right cam to cam guide and torque the retaining bolts to 7-9 ft. lbs.
    18. Install the oil pump chain guide. Torque the retaining bolts to 7-9 ft. lbs.
    19. Install the oil pump tensioner assembly. Torque the retaining bolts to 7-9 ft. lbs.
    20. Pull out the pins on both the left and right hydraulic tensioners. Install the oil pump chain cover.
    21. Rotate the crankshaft two revolutions in the clockwise direction. Confirm the timing mark. Be sure to rotate the crankshaft in the clockwise direction.
    22. Apply sealant on the chain cover and on the cylinder head, cylinder block, and lower oil pan. Be sure these parts are free of engine oil and dirt.
      NOTE Before assembling the timing chain cover, the liquid sealant TB1217H should be applied on the gap between the cylinder head and block. The part must be assembled with five minutes after the sealant is applied.


      0996b43f80201926.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Sealant application (1 inch bead width)-3.8L Engine

    23. Apply sealant on the chain cover.
      NOTE The liquid sealant TB1217H should be applied on the gap between the cylinder head and block. The part must be assembled with five minutes after the sealant is applied.


      0996b43f80201927.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover sealant application-3.8L Engine

    24. Install a new gasket to the timing case cover.
      NOTE It is important that the dowel pins on the cylinder block and holes on the timing chain cover should be used as a reference in order to assemble the timing chain cover in the correct position.


      0996b43f80201928.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover gasket installation (A) gaskets-3.8L Engine

    25. Install the timing chain cover. Torque the retaining bolts in the proper sequence and to specification. The engine should not be started for at least thirty minutes after timing chain cover assembly.

      0996b43f80201929.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover bolt torque sequence and specification-3.8L Engine

    26. Install the timing case cover oil seal.
    27. Continue the installation in the reverse order of the removal procedure.

May 19, 2012 | 2004 Kia Sedona

1 Answer

I have this 89 acura legend 2.7l v6 timing belt removed and the water pump removed, the old pump failed which caused the belt to fail, i have new parts and the pump installed only i dont understand to...


Hi, here is what you need to do. Get all of the timing marks lined up as indicated in the picture below. Put the belt on. Without moving the gears off their marks, make the belt tight across the cam gears and then down the right side to the crank gear. All of the slack must be on the left side to be taken up by the tensioner. Release the tensioner to tighten the belt and then verify the marks are still aligned. If the marks are not aligned, loosen the tensioner just enough to turn the gear that needs to be realigned. After tensioning the belt, rotate the crankshaft clockwise 720 degrees and recheck the timing marks. I have pasted the book procedure below. Please let me know if you still have questions. You must get this right.

jturcotte_2242.gif

jturcotte_2243.gif



jturcotte_2244.gif



jturcotte_2241.gif

  1. If the crankshaft or camshafts have been turned with the timing belt removed, remove the spark plugs and advance the crankshaft about 15 degrees beyond TDC of No. 1 cylinder. Make sure the camshaft sprockets are properly aligned with the marks and return the crankshaft to the TDC mark.
  2. Install the belt in sequence on the crankshaft, the front camshaft, water pump and tensioner pulleys, then the rear camshaft.
  3. To adjust the tension, loosen the tensioner pulley bolt about 1 / 2 turn. The spring will automatically set the proper tension. Torque the bolt to 31 ft. lbs. (43 Nm).
  4. Rotate the crankshaft 6 turns clockwise and check that the timing marks on the crankshaft and camshafts align properly. Adjust the timing belt tension again by rotating the crankshaft to the align the blue mark on the pulley with the pointer. Loosen and retorque the tensioner pulley bolt.
  5. Install the remaining parts in reverse order. Torque the crankshaft pulley bolt to 83 ft. lbs. (115 Nm). When installing the side mount bracket, torque the bolts to 40 ft. lbs. (55 Nm).

Sep 13, 2011 | Acura Legend Cars & Trucks

1 Answer

Como poner la banda de tienpo de un toyota camery


Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence.

Dec 23, 2010 | 1993 Toyota Camry V6

1 Answer

Need directions on how to install a timing chain on a 2002 Saturn L series 2.2 liter along with the allignment marks for the intake and exhaust cams


To Install:
  1. Install or connect the following:
    • Timing chain drive sprocket to crankshaft
      1. Rotate the crank so the mark on the sprocket is at the 5 o'clock position
  2. Assemble chain to the intake camshaft sprocket alignment copper link to the "INT" diamond timing mark on the camshaft sprocket sat_car_22_tmng-chn_pos.gif

    NOTE: When lowering the timing chain rotate the assembly 90° to allow the chain to fall between the cylinder block bosses then rotate the assembly back so the camshaft sprocket is facing forward.
    sat_car_22_tmng-c_hsng_opng.gif

  3. Lower the assembly through the chain housing opening on top of the cylinder head. Use care to ensure that the chain goes around both sides of the cylinder block bosses NOTE: The crankshaft sprocket timing mark will be at approximately the 5 o'clock position.
  4. Route chain around crankshaft sprocket and align silver link to the timing mark sat_car_22_set_tdc.gif

    NOTE: The camshaft sprocket bolts are not reusable; they are torque-to-yield and must be discarded to prevent premature failure.
  5. Install or connect the following:
    • Intake camshaft sprocket loosely onto the intake camshaft then install the new camshaft sprocket bolt finger tight NOTE: It is not necessary to align the sprocket-to-camshaft offset notch at this time.
    • Adjustable timing chain guide through the opening on top of the cylinder head then install the chain guide bolt; torque to 89 lb-in. (10 Nm) sat_car_22_ajst_tmng-ch_guid.gif

      sat_car_22_cm-shft_sprkt_blts.gif

    • Exhaust camshaft sprocket loosely onto the exhaust camshaft with the timing mark on the sprocket aligned with the silver link then install a new camshaft sprocket bolt finger tight
    NOTE: It is not necessary to align the sprocket-to-camshaft offset notch at this time.
    NOTE: The camshaft sprocket bolts are not reusable; they are torque-to-yield and must be discarded to prevent premature failure.
  6. Align the camshaft sprocket-to-camshaft then tighten the camshaft bolt using the following procedure: sat_car_22_crnk_tmng-c_mrk.gif

    NOTE: Do not rotate either camshaft more than 1/2 turn in either direction with the crankshaft at Top Dead Center (TDC). To do so may cause valve to piston contact resulting in a damaged valve and/or a damaged piston.
    • Ensure that the sprocket timing mark is at the 5 o'clock position
    • Rotate the intake camshaft using a 24mm wrench on the flats of the camshaft until the sprocket-to-camshaft alignment notch seats
    • When the sprocket seats on the camshaft tighten the sprocket bolt finger tight
    • Rotate exhaust camshaft using a 24mm wrench on the flats of the camshaft until the sprocket-to-camshaft alignment notch seats
    • When the sprocket seats on the camshaft tighten the sprocket bolt finger tight
  7. Verify that all colored links are aligned with the appropriate marks on the camshaft and crankshaft sprockets NOTE: If they are not repeat steps 1C through 4.
  8. Install the fixed timing chain guide and bolts; torque to 89 lb-in. (10 Nm)
  9. Install the fixed timing chain guide bolt access hole plug; torque to 30 lb-ft. (40 Nm)
  10. Install upper timing chain guide and bolts; torque to 89 lb-in. (10 Nm) NOTE: Use a 24mm wrench to support the camshaft while applying torque to the camshaft sprocket bolt. Do not torque the camshaft bolts against the timing chain as it may damage the timing chain.
  11. Torque the intake and exhaust camshaft sprocket bolts; torque as follows:
    • First Pass: 63 lb-ft. (85 Nm)
    • Second Pass: Turn an additional 30° using a torque angle gauge
  12. Install the sealing ring and tensioner assembly; torque to 55 lb-ft. (75 Nm)
  13. Install or connect the following:
    • Timing chain oil nozzle and bolt; torque to 89 lb-in. (10 Nm)
    • Camshaft cover assembly
    • Engine front cover
    • Negative battery cable; torque to 13 lb-ft. (17 Nm)

Nov 12, 2010 | 2002 Saturn L-Series

1 Answer

How to set the timing on 1998 GMC Sierra 5.7


5.0L and 5.7L Engines To Remove:
  1. Remove the crankshaft balancer.
  2. Drain the cooling system.
  3. Remove the water pump.
  4. Drain the engine oil.
  5. Remove all engine oil pan fasteners except two nuts at rear of engine.
  6. Separate the engine oil pan from the front cover.
  7. Disconnect the crankshaft position (CKP) sensor wire. gm-03-50-845.gif

  8. Remove engine front cover. gm-03-50-849.gif

  9. Pry the oil seal from the front cover.
  10. Inspect the front cover seal area and crankshaft balancer seal area for damage. gm-03-50-846.gif

  11. Rotate the crankshaft until the timing marks on the crankshaft and the camshaft sprockets are aligned.
  12. Remove the crankshaft position sensor reluctor ring. gm-03-50-847.gif

    NOTE: Free play on the slack side of the camshaft timing chain must measure less than 0.43 inch (11Mm) or timing chain and sprockets must be replaced.
  13. Remove the camshaft sprocket bolts.
  14. Remove the camshaft sprocket.
  15. Remove the camshaft timing chain. NOTE: Do not turn the crankshaft assembly after the timing chain has been removed in order to prevent damage to the piston assemblies or the valves.
    gm-03-50-848.gif

  16. Remove the crankshaft sprocket using J 5825-A.
  17. Remove the crankshaft balancer woodruff keys (if required).
To Install:
gm-03-50-850.gif

  1. Install the crankshaft balancer woodruff keys into the crankshaft.
  2. Align the crankshaft sprocket keyway with the crankshaft balancer woodruff key. WARNING
    Wear eye protection when installing crankshaft sprocket.
    gm-03-50-851.gif

  3. Use J 5590 to install crankshaft sprocket.
  4. Install the camshaft sprocket and camshaft timing chain. 9308kg61.gif

  5. Ensure that the crankshaft sprocket alignment mark is in the 12 o'clock position and the camshaft sprocket alignment mark is at the 6 o'clock position.
  6. Install the camshaft sprocket bolts and tighten the camshaft sprocket bolts;
    • Torque to: 18 ft. lbs. (25 Nm)
  7. Install the crankshaft position sensor reluctor ring until completely seated against crankshaft sprocket. NOTE: The composite type engine front cover and seal must not be reused. Always install a new engine cover with a new seal.
  8. Install new engine front cover and bolts.
    • Torque bolts to: 106 in. lbs. (12 Nm)
  9. Clean sealer from corners of oil pan gasket where it meets the engine front cover. gm-03-50-775.gif

  10. Apply a 0.196 in (5 mm) bead of adhesive, GM P/N 12346141 or equivalent, 1.0 in (25 mm) long to the engine front cover to engine block junction.
  11. Install oil pan bolts.
    • Torque bolts to: 106 in. lbs. (12 Nm)
  12. Tighten oil pan nuts.
    • Torque bolts to: 18 ft. lbs. (25 Nm)
  13. Connect the crankshaft position sensor wire.
  14. Install the water pump.
  15. Install the crankshaft balancer.
  16. Fill the engine to the proper level with oil.
  17. Fill the engine to the proper level with coolant.
  18. Test drive the vehicle to confirm the repairs.

Nov 05, 2010 | GMC K1500 Cars & Trucks

1 Answer

I would like a diagram of the 2004 Suzuki forenza timing marks and how to get the belt aroujd the crankshaft is there a way you can give me that information?


from autozone.com


Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Disconnect the Manifold Air Temperature (MAT) sensor connector.
  4. Disconnect the air cleaner outlet hose from the throttle body.
  5. Disconnect the breather tube from the camshaft cover.
  6. Remove the air cleaner housing bolts.
  7. Remove the air cleaner housing.
  8. Remove the right front wheel.
  9. Remove the right front wheel well splash shield.
  10. Remove the serpentine drive belt.
  11. Remove the crankshaft pulley bolts and the crankshaft pulley.
  12. Remove the right engine mount bracket.
  13. Remove the front timing belt cover bolts.
  14. Remove the front timing belt cover.
  15. Using the crankshaft gear bolt, rotate the crankshaft clockwise until the timing mark on the crankshaft gear is aligned with the notch at the bottom of the rear timing belt cover.

56340db.gif

Fig. Aligning the timing mark on the crankshaft gear with the notch at the bottom of the rear timing belt cover.


7c6bcda.gif

  1. Fig. Aligning the camshaft gears with the notches on the camshaft cover.
  2. Align the camshaft gears with the notch on the camshaft cover.
  3. Remove the timing belt.
  4. Loosen the automatic tensioner bolt. Turn the hex-key tab to relieve belt tension.

To install:
  1. Align the timing mark on the crankshaft gear with the notch on the bottom of the rear timing belt cover.
  2. Align the timing marks on the camshaft gears, using the intake gear mark for the intake gear and the exhaust gear mark for the exhaust gear.
  3. Install the timing belt.
  4. Turn the hex-key tab in a clockwise direction to tension the belt. Turn until the pointer aligns with the notch.
  5. Install the automatic tensioner bolt and tighten to 18 ft. lbs. (25 Nm).
  6. Rotate the crankshaft two full turns clockwise using the crankshaft pulley bolt.
  7. Recheck the automatic tensioner pointer.
  8. Install the front timing belt cover.
  9. Install the front timing belt cover bolts and tighten to 53 inch lbs. (6 Nm).
  10. Install the right engine mount bracket.
  11. Install the crankshaft pulley and tighten the crankshaft pulley bolts to 15 ft. lbs. (20 Nm).
  12. Install the serpentine drive belt.
  13. Install the right front wheel well splash shield.
  14. Install the right front wheel.
  15. Install the air cleaner housing.
  16. Install the air cleaner housing bolts and tighten to 89 inch lbs. (10 Nm).
  17. Connect the air cleaner outlet hose to the throttle body.
  18. Connect the breather tube to the camshaft cover.
  19. Connect the MAT sensor connector.
  20. Connect the negative battery cable.

Sep 25, 2010 | Suzuki Forenza Cars & Trucks

1 Answer

Timing belt markings mazda B2500 1998


Timing Belt, Sprockets & Front Cover Removal & Installation Timing belt To Remove:
  1. Disconnect the negative battery cable.
  2. Remove the exhaust side spark plugs, outer timing belt cover, and crankshaft pulley.
  3. Turn the crankshaft until the number one piston is at top dead center (TDC). CAUTION
    The camshaft belt tensioner tool (303-097) can be damaged when trying to relieve belt tension if you attempt to remove the belt without first loosening both the timing belt tensioner adjusting bolt and the spring pivot bolt.
  4. Loosen the timing belt spring pivot bolt, but do not remove it at this point in the procedure.
  5. Loosen the adjusting bolt slowly and release the spring tension.
  6. Turn the tensioner with the camshaft belt tensioner tool (303-097), against the spring pressure, clockwise to the farthest position.
  7. While holding it in this position, tighten the adjusting bolt to hold the tensioner away from the belt.
  8. Remove the timing belt.
To Install:
  1. Be certain that on piston number one, the crankshaft is at TDC with the crankshaft keyway pointing straight up and the circle on the crankshaft sprocket lined up with the notch on the engine front cover.
  2. Line up the timing marks.
  3. Install the timing belt over the crankshaft sprocket going counterclockwise over the oil pump sprocket and over the camshaft sprocket.
  4. Loosen the bolt allowing the tensioner pulley to press against the timing belt. NOTE: The timing belt tensioner should not be tightened or the belt tension will not be evenly distributed over the whole belt.
  5. Turn the crankshaft two revolutions clockwise. Next, slowly bring the crank to the number one position firing position with the keyway on the crank facing up. The dot on the crankshaft gear is lined up with the notch on the front cover.
  6. Check the timing mark alignment again. If necessary, repeat the procedure.
  7. Tighten the bolts. Torque the pivot bolt to 30-40 ft-lb (40-55 Nm). Torque the adjustment/locking bolt to 26-33 ft-lb (35-45 Nm).
  8. Install the crankshaft pulley and tighten the bolt. Torque to 93-121 ft-lb (125-165 Nm).
  9. Install the outer timing belt cover and tighten the bolt. Torque to 70-106 in-lb (8-12 Nm).
  10. Install the exhaust side spark plugs.
Sprockets To Remove:
  1. Remove the timing belt.
  2. Install the camshaft sprocket holding/removing tool (303-098) onto the sprocket.
  3. Remove the camshaft sprocket.
To Install:
  1. Place the key and camshaft sprocket on the shaft.
  2. Install the camshaft sprocket holding/removing tool (303-098) onto the camshaft sprocket and tighten the bolt. Torque to 52-70 ft-lb (70-95 Nm).
  3. Remove the tool then install the timing belt.
Outer Cover To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the fan shroud.
  4. Loosen the bolts on the water pump pulley, but do not remove them at this point in the procedure.
  5. Remove the drive belt, the water pump pulley, and the fan and clutch assembly.
  6. Recover the refrigerant from the A/C system.
  7. Disconnect the A/C wiring connector.
  8. Remove the A/C compressor from the mounting bracket then remove the A/C mounting bracket with the power steering pump still attached.
  9. Remove the outer timing belt cover.
To Install:
  1. Install the outer timing belt cover. Torque to 70-106 in-lb (8-12 Nm).
  2. Install the A/C mounting bracket with the power steering pump still attached. Torque the M10 bolts and stud to 35 ft-lb (48 Nm) and torque the M8 bolt to 18 ft-lb (25 Nm).
  3. Install the A/C compressor to the mounting bracket. Torque to 16-20 ft-lb (21-28 Nm).
  4. Connect the A/C wiring connector.
  5. Refill the refrigerant into the A/C system.
  6. Install the fan and clutch assembly, the water pump pulley, and the drive belt.
  7. Tighten the bolts on the water pump pulley. Torque to 13-17 ft-lb (17-23 Nm).
  8. Install the fan shroud. Torque to 54-70 in-lb (6-8 Nm).
  9. Connect the negative battery cable.
  10. Start the engine. Check for leaks and repair as necessary.
Inner Cover To Remove:
  1. Loosen oil pump sprocket bolt.
  2. Remove timing belt, timing belt tensioner, oil pump sprocket, and crankshaft pulley.
  3. Remove inner timing belt cover.
To Install:
  1. Install inner timing belt cover.
  2. Install crankshaft pulley. Torque to 93-121 ft-lb (125-165 Nm).
  3. Install the oil pump sprocket.
  4. Install the timing belt tensioner. Torque the pivot bolt to 30-40 ft-lb (40-55 Nm). Torque the adjustment/locking bolt to 26-33 ft-lb (35-45 Nm).
  5. Install the timing belt.
  6. Tighten the oil pump sprocket bolt. Torque to 30-40 ft-lb (40-55 Nm).
  7. Torque the camshaft bolt to 52-70 ft-lb (70-95 Nm).

Jul 12, 2010 | 1998 Mazda Pickup

1 Answer

Would like information on timing belt settings on a 1993 Isuzu Rodeo 4X4 3.2 We have already bought the book. It seems that the setting still are not what this particular motor/engine needs are there other...


look for timing marks????
Align groove of crankshaft timing pulley with mark on oil pump.
Align the marks on the camshaft timing pulleys with the corresponding dots on the front plate. (i can email pic if needed)
When timing marks are aligned, no pistons will be on T.D.C.
install timing belt. Align the dotted alignment mark on the timing belt with the mark on the crankshaft gear.
For correct belt installation, the letters the belt must be able to be read as viewed from the front of the vehicle. It is recommended for easy installation that the belt be secured with double clips after it is installed to each pulley. Align the alignment mark (white line) on the timing belt with the alignment mark on the RH bank camshaft timing pulley (on the left side as viewed from the front of the vehicle Secure the belt with a double clip.
Align the alignment mark (white line) on the timing belt with the alignment mark on the RH bank camshaft timing pulley (on the left side as viewed from the front of the vehicle Secure the belt with a double clip.
Turn the crankshaft counterclockwise to remove the belt slack between the crankshaft timing pulley and the RH bank camshaft timing pulley.
Install the belt on the water pump pulley. Remove double clips from pulleys. Turn the crankshaft pulley clockwise by two turns. Measure the rod protrusion to ensure it is within the standard. Standard 4-6 mm (0.16-0.24 in)


13) If out of standard, remove pusher, loosen adjusting bolt, and readjust. (Repeat from step 11). Tighten adjusting bolt to the specified torque. Torque 42 N-m (31 lb-ft)


  1. Pusher
    • Tighten bolt to the specified torque.
Torque 19 N-m (19 lb-ft)


  1. Timing belt cover
    • Remove crankshaft pulley that was installed in step 9.
    • Tighten bolts to the specified torque.
Torque 17 N-m (12 lb-ft)


  1. Oil cooler hose
    • Tighten oil cooler hose bracket bolts to the specified torque.
Torque 22 N-m (16 lb-ft)


  1. Crankshaft pulley assembly
    • Using special tool J-8614-01, hold the crankshaft pulley.
    • Tighten center bolt to the specified torque.
Torque 167 N-m (123 lb-ft)


  1. Crankshaft pulley; P/S belt
    • Tighten fixing bolt to the specified torque.
Install the belt on the idler pulley.

Mar 07, 2010 | 1993 Isuzu Rodeo

2 Answers

Need instructions to replace 1993 Toyota Camry Timing Belt


Hi Kmcarroll77

TIMING BELT REPLACEMENT - 2.2L -1993 Toyota Camry

Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence. See Fig. 6 . On MR2, tighten engine
b7619be.jpg
92cabaf.jpg
Hope this helps, don't forget to rate.

Lazaruselite

Feb 25, 2009 | 1993 Toyota Camry V6

1 Answer

2004 Durango 5.7 timing gear alignment


  1. If tensioner assembly is being replaced, install tensioner and mounting bolts. Torque bolts to 28 Nm (250 in. lbs.) .
  2. Retract tensioner if required. CAUTION: The camshaft pin and the slot in the cam sprocket must be clocked at 12:00. The crankshaft keyway must be clocked at 2:00. The crankshaft sprocket must be installed so that the dots and or paint marking is at 6:00.
  3. Place both camshaft sprocket and crankshaft sprocket on the bench with timing marks on exact imaginary center line through both camshaft and crankshaft bores.
CAUTION: The timing chain must be installed with the single plated link aligned with the dot and or paint marking on the camshaft sprocket. The crankshaft sprocket is aligned with the dot and or paint marking on the sprocket between two plated timing chain links.
b04dbf8.jpg

Feb 13, 2009 | 2004 Dodge Durango

Not finding what you are looking for?
2004 Toyota Sequoia Logo

Related Topics:

366 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...