Question about Chrysler Town & Country

2 Answers

2005 crank position sensor location on a chrysler town and country van

Posted by on


2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 117 Answers

The crank shaft sensor on that model should be on the driver side towards the back of the tranny its not hard to get to.

Posted on Jun 27, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The engine light came on in my 2005 Chrysler Sebring, it started jerking. Can you tell me what the problem is

Posted on Nov 11, 2009

  • lorraainenas Aug 05, 2011

    The same thing is happening with my Chysler Sebring and I got it tested and I put A Cranckshaft sensor in, but it didn't correct the situation. What did you do?

  • lorraainenas Aug 05, 2011

    I didn't put a crankshaft sensor in , Instead I put a camshaft sensor in. It still is jerking, what should I do.



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Replaced bad coil van cranks but wont start?

Sure the new coil is working? Did you check for spark?Is the fuel pump working? Fuel injectors? ECM?

Feb 21, 2016 | 2005 Chrysler Town & Country

2 Answers

Where would i get a diagram to show me where the crank sensor on my 1997 town and country van is

The crank sensor will be located on the back of that engine. By the starter. YouTube has a cool video about it.

Oct 03, 2014 | 1997 Chrysler Town & Country

1 Answer

Crankshaft position sensor for 2005 chrysler town and country

when looking at the left hand side of the engine ( from the front or belt side ) it would usually be down on the block to the side of the crankshaft damper pulley and 4-5 inches back from the front of the engine.

Mar 08, 2012 | 2005 Chrysler Town & Country

1 Answer

Where is located the crankshaft position sensor in a chrysler town country 2003 3.8 engine.

I have same issue on my 2003 TC - 3.8L Van. Do you have a picture of the CPS location?

Sep 10, 2010 | 2003 Chrysler Town & Country

1 Answer

Chrysler 2005 town and country mini van dash lights flicker, gauges go crazy, car shuts off no warning. Changed battery and alternator???

its the positive wire that goes to the fuse box from the battery. its crimped into the main positive wire. it needs a better connection.

Sep 08, 2010 | 2005 Chrysler Town & Country

1 Answer

How do you replace acrankshaft position sensor on a 2005 town and country van and where is it located?

Ohhh this is a difficult one. The crankshaft is not easy to replace in any vehicle, and vans can be harder.

At least the drive belt is in the front of the motor. You'll have to jack up the front of the vehicle and safely support it on jackstands, the crankshaft sensor is located behind behind the crankshaft sensor on the bottom of the serpentine belt. The Belt has to come off, then the crankshaft pulley has to come off, in order to get at the sensor.


Because they may involve removing part of the air conditioning system to get to it, a seriously suggest seeing a mechanic so have the A/C system professional discharged, before continuing.

May 25, 2010 | 2005 Chrysler Town & Country

1 Answer


Here is the location...not knowing your engine size.....




And this is the two type of crank sensors...visuals to help you locate yours:



Apr 18, 2010 | 2005 Chrysler Town & Country

1 Answer

Cranksensor where is it location at 2005 town and country

Hello melvin453: My name is Roger and I will help you. The crank position sensor is located on the rear of the transmission housing above the differential housing. The bottom of the sensor is located next to the drive plate (flywheel). Should you need further help please just ask.Please rate the answer. This way i know it was helpful. Thank You for using Fix Ya.

Nov 18, 2009 | 2005 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,384 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides