Question about Chevrolet Blazer

1 Answer

Changed trans fluid and filter and in the process of putting pan back on broke shift solenoid b replaced it the shift solenoid and it still wont shift show codes for the trans pcm and both shift solenoids

Posted by on

  • vettekilla41 Jun 27, 2009

    no its was on the rear of the trans inside the the pan theres 2 solenoids used a scan tool to find out y it wasnt shifting and it popped codes for the trans pcm and both the shift solenoids i think its an electrical issue not mechanical also trying to find a manual for the trans so i can pin point whats causing it not 2 shift im a mech for the army just need some outside advice cuz im baffled on this one

  • Gary Cecere Sr
    Gary Cecere Sr May 11, 2010

    was there a check ball in the solenoid? It could have fell out!!



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.


    An expert whose answer got voted for 20 times.

  • Expert
  • 109 Answers

Try disconnecting battery for about a minute and reconnect.

Posted on Jun 27, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My 2009 toyota corolla has a code p2757. Its related to a solenoid. how do I go about solving my problem?

well my transmission officially blew up due to the torque converter. I suggest dropping the transmission pan then taking the solenoids out and cleaning the hell out of them, drain as much trans fluid as possible and replace the gasket and filter. Replace the trans pan after putting all the solenoids back into place I also suggest using Lucas Stop Slip Trans Fix when refilling the fluid. DO NOT OVERFILL AND DO NOT UNDERFILL. Take your time on putting new good fluid in not cheap stuff. If all this doesn't work or make a change then the next step is to replace your torque converter. This in involves taking the transmission out pulling the T converter out and replacing it you also have to do a fluid change regardless even after you try changing it the first time to see if it fixed your issue. Any shavings inside the torque converter will contaminate your new fluid if the first fluid change doesn't work therefore 2 fluid changes would be necessary if you don't solve the issue the 1st time after cleaning the solenoids. Try these steps and get back to me and we will go from there. I hope this helps as a brand new transmission is 4,000 dollars. Good luck and keep me posted.

May 18, 2014 | 2009 Toyota Corolla

2 Answers

While drivingtransmission shifts thru all gears but 3rd, doesn't slip just wont go into third gear

fluid and filter would affect all gears not just one . I would run the fault codes and look for a TCM problem with a solenoid /servo problem for 3rd gear.

Mar 21, 2014 | 2001 Pontiac Montana

2 Answers

4t60e wont shift out of 1st, but has reverse...Shift solenoids/pressure soledoids? fluid levels fine, slightly darker than normal, very faint smell...thinking electrical parts failure..input?

Remove the main connector of the trans shafter & test drive it.see do u still have the first gear.if it is not,it is internal transmission problem

Jan 27, 2014 | Cars & Trucks

2 Answers

I have a 2003 lincoln ls with 110,000 miles and there is a hard **** when it is about to go into 3rd gear; there is also a hard **** when I put in reverse. I am told that I need a solenoid assembly...

You need a new Trans Control Solenoid--one unit with all 3 pressure control and 4 shift solenoids, in one unit.
Remove trans pan,gasket reusable,remove filter,remove 7 torx screws and one 10mm wire harness connector bolt,then pull down old solenoid pack.

Part # 9L2Z7G391A 515.30 list/332.20 cost at trans supply house

Do Not Go to a Dealer,unless your Warren Buffet or Bill Gates

Change the fluid a couple more times, after installing the new solenoid pack, and driving a couple weeks with no issues. Add a bottle of Red Lubgard, to your Mercon V Trans Fluid, at the last fluid change

Also--pull injector fuses,crank over engine, and flush Power Steering Fluid. (Dex/Merc Fluid)

Oct 14, 2010 | 2002 Lincoln LS

1 Answer

FORD LASER 1999: Car stays in intermediate gear, (2nd?) And hold light flashes on (maybe when the brakes put on, im not too sure)

Inside the transmissions lower trans pan upin removal you will see electronic solenoids mounted in there. The 3rd gear solenoid is at fault which neds to be replaced. That will get the trans to shift correctly again. Change the filter and fluid at the sam time as well
The solenoid needs to be purchased at a ford parts department as well

Jul 10, 2010 | Ford Laser Cars & Trucks

1 Answer

Leaking fluid

Only so many places these trans 41 TE can leak on the vans. Lines on top, speed sensors(input, output)one is below the lines the other is to right of the lines. Dipstick tube, trans solenoid gasket, Oil pan & extension gasket. Wipe off & clean area very well. Lines leaking, check clamps first before replacing. Speed sensor leaking replace o ring, Dipstick tube replace o ring, Trans solenoid replace gasket, Extension plate replace gasket If the pan is leaking you change the trans filter & put a gasket on the pan. The book says RTV on the pan, but FelPro make a gasket for the pan $6.99. Use a Chrysler trans filter!!!! O rings for sensors, tube around $3 each, trans solenoid gasket $3, extension gasket $10, Filter $11 + gasket $7 & 4qts trans fluid if doing the filter or extension gasket.

Jan 18, 2010 | 2000 Dodge Caravan

1 Answer

1993 chevrolet blazer fullsize 4l60e trans problem

first of all shavings are a bad sign likely internal damage has occured

Jun 22, 2009 | 1993 Chevrolet S-10 Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

211 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

80531 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides