Question about 2008 Dodge Grand Caravan

1 Answer

Remote keys to unlock vehicle don't work - 2008 Dodge Grand Caravan

Posted by on

  • Marvin
    Marvin May 11, 2010

    try reprogramming them.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 50 Answers

If you have replaced the battery in the remote then the remot mite need reprogramming.

Posted on Jun 27, 2009

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
Mike258
  • 1498 Answers

SOURCE: keyless remote wont work, vehicle completely shut down

Hi Russell,

Absolutely no power? No dome light? No head lights? Nothing?
When you step on the brake pedal, no brake lights?

If true, start at the source and pop the hood.

This is going to be a bit of back and forth dialogue. I'll ask some questions and you get me the answers. That way we can get to the root of the problem. To save time, I'll ask multiple questions at a time. Here goes.

  • Check the battery. Is it still there? (Valid question with no evidence of power)
  • Are the terminal clamps tight?
  • Are the terminals clean and free of corrosion?
  • Are all the belts in place and tight? (pay special attention to alternator)
  • If you have a voltmeter. test the voltage at the battery terminals. It should be +12.5VDC.
Try getting a jump, when the cables are attached does anything light up?
Does it turn over and start?
Does it do anything?

Comment me back with your findings
Mike

Posted on Jan 05, 2009

mikek92580
  • 378 Answers

SOURCE: Must use the key to

the battery in the remote is goning dead.goodluck

Posted on Jan 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Chevrolet Tahoe 1999 start then stops ! 2 my


A common issue with the later 90's chevy was an ignition tumbler going bad. So, where you put your key in to start the vehicle--this part needs replaced. One I seen actually stuck in the starting position and burned up the starter before power could be shut off to the vehicle. Lock/Unlock buttons on the door? Try disassembly of switch and cleaning the contacts with electronic parts cleaner, dry and re-assemble. Be sure to use cleaner that is safe for plastics.

Oct 01, 2013 | 1999 Chevrolet Tahoe

2 Answers

This is a dumb question...I just got my Larado a month or so ago.It came with one key,that locks / unlockes diffret doors depending what way you put it in the door (if it don't unlock the doors ya wan


If the key works in all of the locks, it is the Master key. I think GM is the only manufacturer still using a different key for ignition.
In the mid-90's, remote locks were still an option, not a standard feature. Perhaps the easiest way to check whether your vehicle has that option is to ask a dealer to look it up using the VIN, unless you find a remote lock receiver in the vehicle (sorry, I don't know where it is normally installed). If you have a remote lock system, you can use the VIN to order a replacement, but it won't be cheap.
Alternatively, you can have an aftermarket remote lock system installed. Many of these include remote start as well - this is nice for getting the vehicle pre-warmed on cold winter mornings.

Nov 10, 2011 | 1995 Jeep Grand Cherokee

2 Answers

We lost the remolt control and now the alarm is going off,ihad to disconnect the battery,now every time i connect the battery the alarm is going off


You need to find the remote. Once you do,you can use it to turn off the alarm by pressing the unlock button. You can also try pressing the unlock button on the door panel but, I don't know if that will work. You might have to have another remote programed for the vehicle. You can also try putting the key in the door lock and unlocking it.

May 26, 2011 | 2003 Mitsubishi Galant

1 Answer

I bought a honda civic sport 2005 got it resprayed and i built it up and now the alarm keeps going off the key fob doesnt work etheir the battery has been flat . does any body no how to reset the fob or...


Programming
When
Remote control added or replaced. System malfunction.
How
Obtain all remote controls. A maximum of 3 remote controls can be programmed. Switch ignition ON. Repeat procedure below 3 times: Within 4 seconds: Press lock or unlock button. Within 4 seconds: Switch ignition OFF. Within 4 seconds: Switch ignition ON. Within 4 seconds: Press lock or unlock button. System should now lock or unlock vehicle. Within 4 seconds: Press lock or unlock button. Within 10 seconds: Press lock or unlock button of first remote control. System should now lock or unlock vehicle. Press lock or unlock button of second remote control. System should now lock or unlock vehicle. Press lock or unlock button of third remote control. System should now lock or unlock vehicle. Switch ignition OFF. Remove key. Check operation of all programmed remote controls.
IMMOBILIZER CAN ONLY BE SET BY DIAGNOSTIC EQUIPMENT

May 13, 2011 | 2005 Honda Civic

2 Answers

2002 bmw 530i key does not (remotely) unlock doors or trunk but they work fine manually.


Unlock vehicle. Enter vehicle. Close driver's door. Switch ignition ON and OFF. Remove ignition key. Press and hold unlock button. Press lock button briefly 3 times within 10 seconds keeping unlock button depressed. Release unlock button. Some models: LED flashes slowly for 10 seconds. Some models: Central locking system locks and unlocks rapidly to indicate correct programming. Repeat above procedure if central locking system does not work and LED does not flash or LED flashes continuously.

Mar 09, 2010 | 2002 BMW 5 Series

1 Answer

As to me to stitch the second key from ignition (with immobilizer) in memory of my car (Honda CRV-2,4 EX 2002, made in UK) if nearby is not present diller from Honda.


Programming
When
Remote control added or replaced. System malfunction.
How
Obtain all remote controls. A maximum of 3 remote controls can be programmed. Switch ignition ON. Repeat procedure below 3 times: Within 4 seconds: Press lock or unlock button. Within 4 seconds: Switch ignition OFF. Within 4 seconds: Switch ignition ON. Within 4 seconds: Press lock or unlock button. System should now lock or unlock vehicle. Within 8 seconds: Press lock or unlock button of first remote control. System should now lock or unlock vehicle. Press lock or unlock button of second remote control. System should now lock or unlock vehicle. Press lock or unlock button of third remote control. System should now lock or unlock vehicle. Switch ignition OFF. Remove key. Check operation of all programmed remote controls.
NOTE: If less than 3 remote controls are to be programmed, remove ignition key after programming last remote control
NOTE THIS IS FOR YEAR 99-02

Mar 02, 2010 | 2002 Honda CR-V

1 Answer

REMOTE KEY LOCK DOES NOT WORK BATTERYS NEW BUT ALARM WILL NOT SHUT OFF WHEN FIRST START .HOW CAN I DISABLE ALARM


Synchronization
When
Key buttons operated repeatedly while vehicle out of range and system becomes inoperative.
How
Carry out the following within 1 minute: Press key lock or unlock button for approximately 1 second. Manually lock or unlock vehicle. System should now lock or unlock vehicle. If not, carry out programming procedure.
Programming
When
Key added or replaced. System malfunction.
How
Switch ignition ON. Insert key to be programmed into driver's door lock. Lock vehicle manually. Press lock or unlock button. Wait at least 1 second. Press lock or unlock button again. Vehicle horn sounds to indicate correct programming. Remote controls can also be programmed using diagnostic equipment.
NOTE: A maximum of 4 keys can be programmed

Feb 09, 2010 | 2000 Volkswagen Beetle

1 Answer

How to recode remote to vahicle


Programming
When
Remote control added or replaced. System malfunction.
How
Obtain all remote controls. A maximum of 3 remote controls can be programmed. Switch ignition ON. Repeat procedure below 3 times: Within 4 seconds: Press lock or unlock button. Within 4 seconds: Switch ignition OFF. Within 4 seconds: Switch ignition ON. Within 4 seconds: Press lock or unlock button. System should now lock or unlock vehicle. Within 4 seconds: Press lock or unlock button. Within 10 seconds: Press lock or unlock button of first remote control. System should now lock or unlock vehicle. Press lock or unlock button of second remote control. System should now lock or unlock vehicle. Press lock or unlock button of third remote control. System should now lock or unlock vehicle. Switch ignition OFF. Remove key. Check operation of all programmed remote controls.
NOTE: If less than 3 remote controls are to be programmed, remove ignition key after programming last remote control.

Jan 18, 2010 | 2003 Honda Civic

2 Answers

Alarm problem on 2004 chevy tahoe


you will have to write your vehicles vin number down wich is if you look throught the windshild on the drivers side you will see it its a little plate with numbers but right down the vin number and take you drivers license and Registration with you to the chevy dealer ship and request the remote for that vehicle. and they should be able to get you one. as far as i know the remote is the only way to get the alarm off. I hope this helps you

Mar 21, 2009 | 2004 Chevrolet Tahoe

1 Answer

Remote key fob will not work-battery replaced


VW/AUDI/SEAT/SKODA



Remote Control Programming (1997 ON)

Procedure
1. Switch Ignition ON and leave the key in the ignition.

2. Mechanically lock the vehicle using the Drivers door using a second
key.

3. Using the remote control press the Unlock button once, and the horn
will sound once.

4. Wait 6 seconds and press the unlock button once to activate the coding
procedure. The remote control will now be programmed.

NOTE : When performing programming on additional remotes the procedure
is the same, except you press the unlock button 2, 3 or 4 times for the
different remote.

For example : If programming 2 remotes press the unlock button twice with
a 1 second interval between each press, repeat for 3 and 4 remotes.

5. Switch Ignition OFF.

6. Remove key from ignition and check for operation.

7. The coding procedure can be repeated up to 4 times for additional remotes.

8. The ignition must be switched OFF between programming each remote
control.

Remote Control Erasing (1997 ON)

Procedure
1. Switch Ignition ON and leave the key in the ignition.

2. Mechanically lock the vehicle using the Drivers door using a second
key.

3. Press the remote control unlock button 5 times in 1 second intervals.
A short horn will sound.

4. Wait 6 seconds and press the unlock button once to activate memory
erase.

5. Switch ignition OFF, all remotes are now erased.

Dec 24, 2008 | 2004 Volkswagen New Beetle Convertible

Not finding what you are looking for?
2008 Dodge Grand Caravan Logo

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...