Question about 1997 GMC Jimmy

1 Answer

Installed newly rebuilt engine has no power

I had a 97 jimmy 4.3L engine installed. Everything was put in including a new battery, and there is absolutley no power. No inside lights nothing, and the key is stuck in the ignition

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 430 Answers

Bad engine electrical wire.....going to fuse box......or not properly mounted..check wire for loose or missing connections...

Posted on Jun 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Just installed new ecm on 04 gmc envoy, now engine wont start. everything else works. what should i do?


when ever you replace ECM computer, you must take out your CHIP , to put it into your new ECM. did you do this ?????? if not your engine will not run ,even with GOD turning the key .

Feb 01, 2013 | 2004 GMC Envoy

2 Answers

Engine code 12; installed new rebuilt 3.0 engine in 1988 dodge Caravan (same engine that was in van). engine light and maintenance light will not go out. We have put well over 1,000 miles on new eng


The maintenance required light is a reminder to have the vehicle's emissions systems checked and then be reset using Chrysler's DRBII scanner. It will not go off on its own and has nothing to do with your problem. Code 12 means that the logic module has lost it's memory power (direct battery feed). Without the memory power it cannot keep engine operating conditions or other fault codes when you turn the key off. Check battery connections and engine ground straps. Get yourself a good wiring diagram and check the connections at the computer. After you solve code 12 you might start finding other codes that will point you in the direction of the other performance issues.

Apr 08, 2012 | 1988 Dodge Caravan

2 Answers

Just installed a rebuilt 360 in a 1999 dodge truck and it starts and idles but it wont accelerate ?


if it is idling and you push on the gas and nothing happens. sounds like you did not connect the throttle cable back up. Now if it idles and you put it into drive and push on the gas and the engine revs up and you do not move then you didnt hook up the transmission up right. if this is a manual transmission you put the pressure plate on backwards.

Feb 21, 2011 | Dodge Pickup Cars & Trucks

1 Answer

I rebuilt the whole top of my engine in my 74 cadillac coupe deville--472 engine...when i put everything back, i replaces the battery, starter and solenoid, cables are new and clean. and i didnt touch the...


Remove the spark plugs and turn the engine over.It should spin fast a freely. If not that thrust washer tothe cam may have been installed backwards if you had removed it

Jun 03, 2010 | 1974 Cadillac Eldorado

1 Answer

94 ford tbird rebuilt engine wiring harness plug too small


If the rebuilt motor is a twin of the original,use the original wire harness. Why would the motor have a harness on it?You usually keep everything,including your intake system and just get the long block.

Mar 09, 2010 | Ford Thunderbird Cars & Trucks

1 Answer

I have a 1993 GMC Jimmy with the Vortec 4.3L engine, VIN code is W. It has CPI fuel injection with a new O.E.M. CPI unit installed. My problem is that the car 'surges' during hard acceleration (such as...


put a fuel pressure gauge on it and check cold and hot pressures if you have too take off hood and drive with gauge installed so you can see it. duct tape and a ruler to hold it up .should have 50 psi or more if it drops below thirty it cuold have trouble hope this helps.

Jan 11, 2010 | 1993 GMC Jimmy

1 Answer

How do i install a new thermostat in a 97 gmc jimmy


look at the radiator and follow the top hose into where in meets the engine and the thermostate is in the piece that is connected to the engine. easy enough to do.

Jan 01, 2009 | 1997 GMC Jimmy

Not finding what you are looking for?
1997 GMC Jimmy Logo

Related Topics:

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...