Question about 2001 BMW 325

1 Answer

Break calpier 2000 v 316

Same problem break keep locking on .
there is no reason as i can see but every now and again it just locks on !

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • BMW Master
  • 2,019 Answers

If rear, then parking brake possible cause.
But front and rear calipers often lock from corrosion on piston or binding on sliding parts.
Remove caliper, remove piston with compressed air or greasegun, clean corrosion, clean all grease out, replace seals. (compressed air is dangerous!)

Posted on Jun 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi I keep having the same problem with my land rover discovery series I, for some reason a little piece of plastic inside the door handle keeps breaking I've already replaced it once and now its broken...


I am guessing that the plastic bit is what holds the wire /rod in the hole of the lock lever It is a common connection piece in lock manufacture. If that is the case the piece that breaks is the bit that clips around the rod section(the clip fingers break off). Two fixes spring to mind is to use a piece of small wire (paper clip ) reposition the clip and tie to rod ( small zip tie may be easier) or 2 there are metal clips that do the same job( Mazda early models use these) but you could possible get them from a panel repair shop

Jun 20, 2013 | Cars & Trucks

1 Answer

If a power steering pump locks up does it have to be replaced?


the power steering pump locking up is the reason ur serpentine belt broke. on front of power steering pump is a pulley which must spin freely. when this pulley locks up, things break...and yes u definitely need a new power steering pump.

Feb 06, 2013 | Ford Ranger Cars & Trucks

1 Answer

Ford maverik, 1996 2.4 petrol. Breaks failed once, abs activated, pedal didnt toucn floor, but it didnt wanna stop. Abs was working v hard but with little breaking. Would this happend if one of the breaks...


The most common reason would be a bad wheel sensor. the computer may have received a signal that one wheel was locking up and so it keeps releasing brakes until all wheels are spinning at same speed. this can get scary, your braking but car wont stop. have the abs computer scanned for any codes, the codes will tell you where the problem is, lets hope theres a code. otherwise you will need to wait until it gets worse or happens again. good day.

Feb 22, 2012 | 2005 Ford Maverick 2.7

1 Answer

How do I remove rear rotor to have them turned?


jack up wheel, remove wheel,remove brake caliper, slide of rotor.Note use a clothes hange to hold up brake calpier as you do not want to break the brake line. Good Luck Tim

Sep 11, 2010 | 2006 Jeep Commander

1 Answer

Gears are locked.


neutral-park brake safety switch,it is connected at top of break paddle on fire wall it is a little button that goes in when brakes are pressed

Jul 02, 2010 | 2002 Saturn L-Series

4 Answers

Front brakes lock up


your brake calipers are stuck! replace the brake calpiers and won't hurt to replace the hoses at the same time.

Mar 28, 2010 | 1986 Toyota Pickup 4WD

1 Answer

Trying to remove ingition lock cylinder


After cover has been remove you'll see the bolts that hold the lock, when lock was install the head of the bolts are made to break off for theft reasons, get a small chisel and hit the bolt as to loosen it, once it breaks loose they'll come off easy, when installing new lock keep turning bolt till the head of the small bolt breaks off, it made to do that.

Jan 05, 2010 | 1998 Toyota Camry

1 Answer

Ignition switch


You wrote ignition switch/lock cylinder. Which part did you replace? The ignition switch or the ignition lock cylinder? The electrical ignition switch is what is bad.

May 15, 2009 | 1997 Chevrolet Blazer

1 Answer

The brake caliper on my 2000 Yukon keep locking up.


I would chg. the break hose, the one from the caliper to the hard line. Break fluid runs to caliper and back thru same hose, fluid is not running back hense caliper stays compressed or locked.

May 06, 2009 | 2007 GMC Yukon

1 Answer

Anti lock abs and traction control light.


did you accidently unplug a rear speed sensor

Feb 27, 2009 | 1996 Cadillac Seville CA Value

Not finding what you are looking for?
2001 BMW 325 Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...