Question about 2005 Ford F-150

Open Question

2005 ford f-150 easiest way to remove the engine

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

STEVIE_N_24
  • 147 Answers

SOURCE: the back light bulb is out on my 2005 ford f-150

Tilt down the tailgate and you should be able to locate the screws for the globe assembly.

Posted on Apr 01, 2009

LEFTY64
  • 69 Answers

SOURCE: blown heater core in a 1977 ford f-150 pick-up

1976-79 Without Air Conditioning

  1. Disconnect the temperature and function control Bowden cables from the heater housing. This must be done to prevent damage to the cables.
  2. Disconnect the wires from the blower resistor.
  3. Remove five screws attaching the air inlet (vent) duct to the heater housing.
  4. Disconnect the blower wires.
  5. Drain the radiator and remove the heater hoses from the heater core.
  6. Remove three heater stud retaining nuts and remove heater.
  7. Remove gasket between the heater hose ends and the dash panel at core tubes.
  8. Remove heater core cover and gasket (four screws).
  9. Pull heater core and lower support from heater.

To install:
  1. Install foam gaskets on heater core and install in heater assembly.
  2. Install the core seal and cover plate.
  3. Position heater assembly in vehicle and install three stud retaining nuts.
  4. Connect heater hoses to heater core and fill radiator.
  5. Connect blower motor wires.
  6. Place defroster nozzle on heater so that the defroster and heater openings are in the up position, and there is no air leak around the seal.
  7. Install air inlet (vent) duct to heater. Push duct firmly against seal on side cowl and tighten five attaching screws.
  8. Connect wires to blower motor resistor.
  9. Connect temperature and function control cables to heater, and adjust the cables.
  10. Reinstall gasket between the heater hose ends and the dash panel at core ends.
  11. Fill Cooling System.

  12. Hope this helps you! Please remember to rate my solution.

    Lefty64

Posted on Apr 09, 2009

sscullys
  • 984 Answers

SOURCE: 2005 ford f-150...4 wheel drive will not

Operationally vacuum holds the IWE ( Integrated Wheel Ends ) out, and once vac is removed the spring engages the IWE.

Lift and support the front of the truck so the front wheels are off the ground ( take safety precautions, chock wheels, jack stands, etc )
Key on, engage 4x4 and try to turn the front drive shaft.
If it turns it is a problem with the transfer case.
If it doesn't it is a front axle engagement problem.

- If the front drive shaft does not turn :
Shut of the truck ( still jacked up, and supported ) remove the vac lines from the IWE. The spring should push the gears in, without the vac line on.
Check the vent line ( tube that is routed into the engine compartment with nothing attached to it ), for blockages.
If the vent line is clear, and with the vac lines off the IWE should be engaged ( both front wheels locked ).
If they lock, the problem is with the IWE solenoid not shutting off vacuum to the IWEs. There is a TSB on the 2004-2006 IWE solenoids, a newer revision has been made, and used from 2007 and newer MYs.

Here is a block diagram of the IWE system
b3ce05f.jpg

Posted on Dec 20, 2009

  • 978 Answers

SOURCE: when i turned on the air conditioner dog food

get a long flexible tube and tape it to a hoover try **** it out that way a strange one how did it get in there

Posted on Apr 20, 2010

  • 14036 Answers

SOURCE: What is the easiest way to remove the rear hub on a 2005 Ford Explorer?

you need a hub wrench where the drive tangs engage the four slots in the hub nut and remove the nut.go to auto parts stores they carry hub wrench you also need 3 jaw puller loosen the rear hub to point of removal.

Posted on Nov 16, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I had my oil pan replaced and now I have no oil pressure.


you need to prime the oil pump before runninning the engine, easiest way is to locate the oil pump drive and attach a drill to spin the pump so the oil gets around all the galleries

Oct 14, 2014 | 2005 Ford F-150 SuperCab

1 Answer

Whats the easiest way to remove a oil pan for a 1989 XLT F-150 Lariat


pls specified your engine size and tranmission(2WD/4WD) ............lift the vehicle and drain engine oil, remove all bolts and be carefull for removing oil pan, oil pan gasket is reusable

Jun 26, 2010 | 1989 Ford F 150

1 Answer

2005 Dodge Grand Caravan 3.8 liter engine needs water pump replac


3.3 & 3.8 same block. V6 no special tools needed

Sep 29, 2009 | 2005 Ford F-150

1 Answer

The ABS light stays on, sound in the rear, seems to be the rear gears-2005 Ford F-150-how do I change it out?


if the gears have gone there is a good chance the case has been damaged too... your easiest bet would be to find a complete rear end at a junk yard, probably cheaper too.

Jun 25, 2009 | 2005 Ford F-150

1 Answer

Front brake pads


Raise And Support Truck, Remove Wheel, Remove 2 Bolts Holding Brake Caliper On , Use Large "C" Clamp to Push Piston IN to Open up Space for New Pads Install Pads Reverse of How They came Out, Place Caliper Onto Rotor / Ancor and Install 2 Bolts.--------Do This ONE AT A TIME and After Completion Start Engine and Softly PUMP Brake Pedal Untill It Returns to Normal Hight. Hope this hellps you .

Jun 03, 2009 | 2005 Ford F-150

1 Answer

I need to know the pressure in the gaspump


with the key on and the engine off you should measure between 35 and 70 lbs fuel system pressure. this is true whether you have v6 or v8 gasoline engine.

May 26, 2009 | 2005 Ford F-150

1 Answer

Location knock sensor 2005 ford f150 5.4engine


It will be easiest to find by getting under the truck and looking up at the engine. It will be a round sensor that screws into the side of the engine block. It will only have one or two wires going to it, usually just one. It is round and about 1 1/4 inches across. Not sure if it is on the driver or passenger side, but it should be pretty easy to find.

May 13, 2009 | 2005 Ford F-150

1 Answer

The back light bulb is out on my 2005 ford f-150


Tilt down the tailgate and you should be able to locate the screws for the globe assembly.

Apr 01, 2009 | 2005 Ford F-150

2 Answers

Dodge 2005 Grand Caravan water Pump replacement


JUST COMPLETED THIS JOB TODAY. MAKE SURE THE ENGINE HAS COOLED DOWN . IT TOOK APPROX 2 1/2 HRS. DISCONNECT THE NEGATIVE POST ON THE BATTERY. JACK UP PASSENGER SIDE FRONT AND SUPPORT ON JACK STANDS. REMOVE PASS. FROUNT TIRE. DRAIN RADIATOR INTO CONTAINER FOR PROPER DISPOSAL OR REUSE. USING FLOOR JACK PROVIDE SLIGHT TENSION ON OIL PAN WITH A SHORT 2 X 4 WOOD PIECE TO PROTECT OIL PAN. LOOSEN 3 ENGINE MOUNT BOLTS ON PASS. SIDE OF ENGINE COMPARTMENT. ALLOW APPROX 1" BETWEEN SHOULDER OF BOLTS AND MOUNT. LOWER ENGINE UNTILL BOLTS ARE SET ONTO MOUNT. REMOVE ENGINE SPLASH SHIELD INSIDE WHEEL WELL OF REMOVED TIRE. LOCATE WATER PUMP AND LOOSEN 3 PULLEY MOUNTING BOLTS (THIS IS WHILE BELT IS ON PULLEY) REMOVE SURPENTINE BELT AND CONTINUE TO FULLY REMOVE THE PUMP PULLEY. IT WONT COME OUT AS THE PUMP & PULLEY HAVE TO COME OUT TOGEATHER. REMOVE 5 WATER PUMP BOLTS AND CAREFULLY WORK WATER PUMP OUT BETWEEN THE ENGINE AND VEHICLE FRAME. CLEAN ALL MATING/GASKET SURFACES AND BOLTS. USING A SMALL AMOUNT OF TACKY SEALENT TO INSURE THE NEW WATER PUMP SEAL STAYS IN PLACE, THE INSTALL IS PRITTY MUCH THE REVERSAL OF REMOVAL.

GOOD LUCK, REMEMBER TO TIGHTEN ALL BOLTS TO MFR SPECS AND BLEED THE AIR OUT OF THE COOLANT AS REQUIRED.

Mar 30, 2009 | 2005 Ford F-150

1 Answer

Whats the easiest way to remove the A/C copmpressor And install a compressor bypass pully?


thay offer 2 belts for it,one is with a/c and the oter is without a/c. so just take the compressor off and use the belt for no a/c.

Jan 16, 2009 | 2005 Ford F-150

Not finding what you are looking for?
2005 Ford F-150 Logo

Related Topics:

358 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...