P0441 trouble code - 2006 Volkswagen Jetta

Nothing at all .
P0113 OBD II Trouble Code

https://www.obd-codes.com/p0441

Here's a link to code P0455, P0455 OBD II Trouble Code Here's the link to code P0441. P0441 OBD II Trouble Code

P0441 code is likely bad or missing gas cap.
check this site for more explanation:
http://engine-codes.com/p0441_lexus.html

You have a small leak somewhere in your fuel system. Unfortunately these are tricky to track down because it could be anywhere. Check out this thread for a few things to check:
http://forums.vwvortex.com/showthread.php?5603935-Stubborn-P0441-code

code P0441 EVAP purge flow monitor fault.

Trouble Code: P0441

Small hoses or cuts present in the EVAP vapor hoses/linesEVAP canister purge solenoid is damaged or is stuck openPCM has failed

P0441 Evaporative Emission Control System Incorrect Purge FlowOBD-II Trouble Code Technical Description

Evaporative Emission Control System Incorrect Purge Flow
What does that mean?

This indicates that a part of the EVAP control system is no longer functioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

EVAP emission canister purge is controlled by a valve which allows engine vacuum to pull stored fuel vapors from fuel tank into the engine to be burned, rather than be vented to atmosphere. A vacuum switch is used to detect when flow exists. If the PCM commands purge and sees that the switch is closed (indicating no detected purge flow) P0441 is set.
Symptoms

Likely, no symptoms will be discernible to the driver, other than the illuminated Check Engine Light.
Causes

A code P0441 could mean one or more of the following has happened:

• Bad vacuum switch
• Broken or damaged EVAP line or canister
• Open in PCM purge command circuit
• Open or short in Voltage feed circuit to Purge Solenoid
• Faulty purge solenoid
• Restriction in EVAP solenoid, line or canister
• Corrosion or resistance in purge connector
• Bad PCM

Possible Solutions

With a P0441 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

• Common Chrysler fix - Replace Leak Detection Pump / LDP
• Repair damaged EVAP lines or canister
• Repair open or short in voltage feed circuit to Purge Solenoid
• Repair open in PCM purge command circuit
• Replace purge Solenoid
• Replace vacuum switch
• Repair restriction in Evap line or canister or solenoid
• Repair resistance in purge connector
• Replace PCM

Other EVAP DTCs: P0440 - P0441 - P0442 - P0443 - P0446 - P0453 - P0455 - P0456

Trouble code P0441 indicates EVAP emiddion control system incorrect purge flow.
Possible faulty purge valve or circuit.
Possible causes: purge line plugged, vacuum hose failure, EVAP purge solenoid failure and/or emission canister clogged.

The coolant sensor is a 2 wire sensor located in the thermostat housing.

P0440= Evap Control Sys Malfunction
P0441= Evap Control Sys Purge Flow Fault
P0446= Evap Control Sys Vent Ckt Malfunction

Could be a loose gas cap, or it was left loose once. P0441 means: p0441- evap purge system performance. In some cases disconnecting the battery over night will clear the code.
Take off the Negative cable only always wear safety glasses when working with a car battery.

Check your gas cap first make sure it is tight