Question about 1998 GMC Sierra

1 Answer

I have a 93 gmc serria 350,2 wheel drive,5 speed,need to change out pressure plate is it hard to do.what all i have to do,would i have to bleed the slave

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

To change the pressure plate you will need to drop the transmission.. i dont think you will have to bleed slave cyl.

Posted on Jul 02, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to adjust clutch on 2001 f 350 6 speed manual trans pick up truck


as i understand the set up the hydraulic clutch needs no adjustment as is compensated for wear by the slave cylinder design hope this is of some help

Jul 17, 2014 | Cars & Trucks

1 Answer

3/4 tonne ford 4x4 93 clutch has no give can't


Had a 92 Ford 3/4 ton 4x4. And the same problem. I changed the clutch master cylinder, slave cylinder (inside of bellhousing), Disc. pressure plate, & throwout bearing. Cost some money but it was worth it. Never had another problem.

Aug 23, 2013 | Cars & Trucks

1 Answer

I got a few questions i got a 1992 gmc serria sle model with a 5.7 th700r4 tranny and is 4 wheel drive the first question i have is if u go to put in in reverse with it in 4lo and turn the steering wheel...


Trnasmission going out, Did you know that reverse is the same as second gear. Does it slip in second gear are should I say have a hard upshift like around 20mph. Got a friend have them drive it in reverse and see how fast the drive shaft is turning also do you hear a whinning noise.
























Apr 21, 2011 | 1992 GMC Sierra C3500

1 Answer

I have a 2005 gmc serria with 60k miles, replaced the power steering pump, but after bleeding the pump and running for about an hr, the fluid burns and is hard to steer


OK, I would maybe try to jack up the front, and turn the steering wheel left and right a few times and check for the fluid level to make sure it's not low.

Try to bleed again, if necessary.

How does it sound?

Oct 28, 2010 | 2000 GMC Sierra

1 Answer

Low oil pressure 93 GMC P/U w/350 motor w/205,000 miles gauge


While engine is running, open the cover where you add oil to engine and see if you see a good flow of oil, if good flow, could be as easy as replacing oil sending sensor. got to realize that if poor maintenance history your engine may not be building enough pressure at iddle to move your hydraulic operated valves, only when you rev it up it will pump enough to run smooth. if running engine too long, you may cause more damage to other engine components such as crankshaft and cam shaft bearings. if you can spare a few bucks, have a good mechanic check your oil pressure with a mechanical gauge. another cheap option is to replace oil pump. last resort if you love your truck as much as we do,replace engine or rebuild it. At 205,000 this is a normal symptom, other than timing chain problems, most engines don't make it that far. hope this helps!

Mar 01, 2010 | 1993 GMC Sierra K1500

1 Answer

2005 GMC 1500 transfer case does not work below 50 deg


My 2005 Serria 4x4 truck will not work in 4 wheel drive high or low, but my Auto 4 wheel will work. Is there something wrong in the transfer case with electrical or mechanical?

Oct 23, 2009 | 2005 GMC Sierra

1 Answer

How to remove the cooling fan from the the water pump on a gmc 150 serria two wheel drive 350 engine


Depends on year modle. The older ones had 4 nuts holding them to the water pump. The newer style is a screw on fan clutch. It is right handed thread. 36mm if memory serve me right

Oct 11, 2009 | GMC Sierra 1500 Cars & Trucks

3 Answers

1999 Dodge Ram


Your pressure plate is going out.
Please Rate this !

Jul 07, 2008 | 1999 Dodge Ram

Not finding what you are looking for?
1998 GMC Sierra Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...