Question about 1991 Buick Regal

1 Answer

Need to take door panel off to replace the window that was smashed need a diagram if possible.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 1,986 Answers

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I need a diagram so i can replace right side elec. window unit

You must have the replacement window mechanism before you attempt to take off the door panel. You don't want double the work ! Window winder mechanisms come with or without motors depending on your needs ! It can be tricky but perfectly possible by a confident DIY'r.The door panel has pop fasteners and 2/3 screw/bolts in the door pull/inner handle.

Aug 26, 2012 | 2001 Volkswagen Beetle

1 Answer

My 1989 buick skyhawlk passenger side window keeps falling its not electric

your window crank mechanism in the door is striped or bent, remove inner door panel and inspect window parts, look in bottom of door for possible parts that may have fallen off. KEEP all fingers clear of moving parts as if the window falls or something you could loose or injure them !!!!!!!!!!!!!!!!! Cant express enough but be careful. I have had cars fall on me, smashed fingers, broken fingers, broken hand, all due to car repairs so believe me when i say a mechanical window mechanism will remove or smash a finger very easily.

Feb 25, 2011 | 1989 Buick Skylark

2 Answers

I have a 2005 jeep grand cherokee limited, the doors on the passenger side were smashed so i replaced them with 06 doors, the wiring harnesses plugs for the door panels are not the same, so i took all the...

Before you "hack into the harness," try to change over everything so that all the wiring,switches and motors on the new doors are the original ones. A lot of the switches have circuit boards matched to the vehicle wiring and other switches. It is possible that your new doors have the wiring on the motors reversed, so that when you try to wind the window down, it wants to wind it up. Also before getting in to the wiring, if nothing else is working, make sure the motors for the window are actually working by disconnecting them and supplying the 12Volt positive and negative to them.

Feb 22, 2011 | 2005 Jeep Grand Cherokee

1 Answer

Back windows don't row down.

remove the interior door panel and you should be able to inspect the mechanical arm that controls the windows movement. chances are part of this has broken losse and will need replacing. always be careful as you dont wont to drop the window and smash it.

Apr 22, 2010 | 1991 Lincoln Town Car

1 Answer

I need to replace mirror on kia sedona 08 passanger wing mirror

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can remove the bolts securing the mirror onto the door

Oct 01, 2009 | 2004 Kia Sedona

1 Answer

How to replace an entire Car Door? (Ford Escort)

You will need to remove the door panel and unplug and wiring for power windows, locks, speakers, etc. Then support the bottom of the door with a floor jack or block of wood. A friend to help would be good. Unbolt the door at the door hinge either on the door or the body, depending on how it is mounted. You will need metric wrenches, and sockets, screwdrivers for the door panel .

Mar 11, 2009 | 1996 Ford Escort 4 Door

1 Answer

2004 crown victoria lx smashed driver side window

normally you have to loosen the track and it comes out as one whole assembly stop by a dealer in the parts department and ask them to print out a diagram or show them the part you are having the problem with

Aug 27, 2008 | 2003 Ford Crown Victoria

Not finding what you are looking for?
1991 Buick Regal Logo

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts


Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides