Question about 1989 Ford Ranger

1 Answer

2000 ford ranger 5 speed problems.

2000 ford ranger wont shift into gear when it's hot. Have to rev it up to get it into gear. When i come to a stop and gear down from 1st to neutral I have to yank it into neutral and hear a big clunk sound. Could it be a master cylinder or possibly have air in my line?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

Your clutch disk and pressure plate and throw out bearing need to be replaced.

Posted on Jun 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will these 2002 ford ranger transfer cases interchange,mine is reg cab 4x4 standard 5 speed 5T13-54-000-038[1L547A195CE]other Access cab 4x4 Automatic 6C13-54-000-037 [1L54-7A195-CC] outsides are same


ONLY use the identical item as the original equipment.( Don't waste your time looking at other products). If you use a different unit you will have significant issues.

Nov 29, 2015 | 2002 Ford Ranger Regular Cab

1 Answer

My 92 ranger 5 speed is hung in gear. you can shift it out of gear but the transmission stays in gear. what is wrong?


i had the same problame in my 1989 ranger xlt 4x4 i speed shifted a trans that wasent ment to and my trans got stuck in second and wouldent come out had to take it somewhere to get the forks in the trans replaced turns out i bent the forks and it wouldent come out of second

Jul 11, 2014 | 1992 Ford Ranger

1 Answer

Speedodometer stopped working, o/d light flashing and my truck does not want to go out of first gear???


The best thing would be to have transmission control module - ( computer ) checked for DTC'S - diagnostic trouble codes . The flashing O/D light is trying to tell you that . The transmission is in limp home mode . A sensor or shift solenoid is most likely the problem . Your transmission is electronically controlled , has sensors , shift solenoids , an a computer that controls it all , plus electrical signals (inputs) from the engine computer .

May 07, 2017 | 2000 Ford Ranger SuperCab

1 Answer

I have a 94 Ford Ranger with a 4.0 engine and a 5 speed trans. The truck has been sitting for a while and now when I drive it the shifting is hard going into 2nd and 3rd. It shifts fine when sitting...


the shift sinkcranizers are dry .may have to pull the shifter and use some white lithum grease on it work the shifter from gear to gear working in the grease drive the truck for about 25-30 miles and change trans fluid

Feb 03, 2011 | 1994 Ford Ranger Supercab

1 Answer

I have a 1989 ford ranger five speed manual 2.3 liter 4 cyl i am haveing problems gettin it to go into gear and the clutch is also in the floor but if i turn the truck off it will go into gear and if i...


do this...

make sure the reservoir is full
engine off and pump the clutch pedal slowly about 5-10 times
while holding the pedal down have assistant open the bleeder on the master located in the trans

if you get a good squirt then your concern is the master
if no squirt then replace the slave

neither job is quick but the slave is 1/2 time

Mar 28, 2010 | 1989 Ford Ranger

1 Answer

2003 Ford Ranger-5 Speed. At times is very hard to get into gear


Your clutch is not releasing all the way. (Assuming the problem is not internal to the transmission) Bleed the system. If that doesn't work, rebuild the clutch master cylinder and slave cylinder and bleed again.

Aug 12, 2009 | 2003 Ford Ranger Regular Cab

1 Answer

Over drive light blinking after about 5 miles of driving.


abs (ABS)sensor is the anti-brake skid sensor and has nothing too do with the transmission
you are referring to the vehicle speed sensor (VSS) run the fault codes as the TR sensor and the TCM are most likely the faulty sensors

May 07, 2017 | 2000 Mazda Protege

1 Answer

Idle speed problem


I had a similar problem, engine would fluxuate engine idle speed. I had to change the "Throttle Position Sensor." You might have that checked out.

Jul 16, 2008 | 1989 Ford F 250

1 Answer

Hard shift and blinking overdrive


The blinking overdrive button is telling u that a serious fault has occurred in the electronic controls or a mechanical fault such as excess slippage is occurring.

Jul 16, 2008 | 2000 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

266 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...