Question about 1995 Honda Accord

1 Answer

Plug wires and distributer cap

My 1995 honda accord im putting new wires in it and i need help plugging them into the right distributer hole so it will run good and not spit and sputter.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 14,036 Answers

For the 1.5L -1.6L- 2.2L and 2.3L ENGINES. from left to right engine cylinders is 4 3 2 1 .now at distributor cap .get a piece of paper draw a big circle now at top of circle from left to right will be 2 then 1 from bottom of circle left to right will be 4 then 3.thats where you will put your plug wires.now the circle you draw 2 upper left of circle 1 upper right.at bottom circle 4 lower left of circle and 3 at lower right.

Posted on Jun 26, 2009

  • Jonah Oneal Jun 27, 2009

    i meant to tell you .the first two plugs on distributor facing wind shield from left to right is 2 then 1.from the front of car 4 and 3 is the distributor other plug wires.you draw a circle on piece of paper that will be your guide for spark plug wires to engine.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to put back spark plug wires to a 92 honda accord


the easiest way is to do one at a time when working with plugs or wires.but if you don`t then cylinder 1 is on the end of the motor were the pulleys are then 2,3,4.this i think is a distributer system so the cap is usually marked were cylinder 1`s wire is installed.then you have to see which way the distributer rotates.then the next wire to #1 in the direction the distributer rotates will be the next wire in the firing order.the firing order is 1342.

Oct 31, 2011 | 1992 Honda Accord

1 Answer

Rebeuilt the engine with new gaskets and seals.


Most likely a timing problem. You may have crossed the plug leads, put the distributer in one tooth out, or not set the valve timing correctly. It could be some other things too, but try these first.

Mar 31, 2010 | 1995 Honda Accord

1 Answer

How to install new ingnition wires on a 1995 Honda Accord with a 2.2 liter 4- cylinder engine Wires were detached from the distributor. I need to the know the sequence for the installation of the new...


The firing order on most inline 4's is 1-3-4-2. If number one is marked on the cap then all you have to do is take the cap off and have someone crank the engine with the starter to see which way the rotor turns.
If the cap is not marked remove number spark plug and hold your finger over the hole, while some one bumps the starter. When you feel compression (air blow out of the hole) stop, look at which terminal on the distributor cap the rotor is pointing to, that wire goes to number one. Number one is the one closest to the belt end of the engine. Good luck!

Feb 05, 2010 | 1995 Honda Accord

1 Answer

Low spark in 1998 honda accord


Have you tried a set of plugs and wires?If so then you need to take the distributer cap of and check it for "carbon tracking",a black residue on the inside due to a worn pick-up in the cap.You should replace the cap but in a pinch you can remove it[mark all the plug wires first]and wash it with dishsoap the completely dry it out by wipeing it out with a rag and putting it in the oven for about 20 minutes on 150 degrees.Put it back on and get a new cap in the neer future.

Dec 14, 2009 | 1998 Honda Civic

1 Answer

Lost power wen i put new plugs and wires on


on 3.1 here is the firing order--1-3-5 is in back, 2-4-6 is in front. coil order from left to right. 5-2-3-6-4-1, on 2.4 it is--from left to right, 1-2-3-4.on 2.2 it is--left to right, 1-2-3-4 and wiring order is 1-3-4-2. hope this helps, also on 2.4 firing order is--1-3-4-2.

Sep 27, 2009 | 2001 Chevrolet Malibu

1 Answer

Car will not start hasno spark tachometer doesn't work


Your distributer is probably the cause. They are a common problem among hondas. Car will turn over but not start and run right? No spark from spark plugs or tach too. To be sure its not a snapped timing belt, see if you have compression by removing a spark plug and put your finger or some sort of similar object in the hole and see if when cranking the car up if it blows out the object of your finger. I'd bet its the distributer to be honest..but check compression first.

Sep 07, 2009 | 1995 Honda Accord

2 Answers

I have a 95 honda accord sputers at stop


getting oil on my plugs on 97 honda accord any help or suggest

Mar 17, 2009 | 1995 Honda Accord

1 Answer

Honda Misses.


Pin point the dead hole and check that injector.

Dec 23, 2008 | 1995 Honda Accord

Not finding what you are looking for?
1995 Honda Accord Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...