Question about 2000 Ford F250 Super Duty Crew Cabs

1 Answer

F250 won't idle properly.

2002 F250 Super Duty w/6.8L V10. Truck won't idle. Replace the throttle positioning sensor, the mass air detector, & the fuel filter. Truck runs fine after you get it going, pulls a load good.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 51 Answers

Idle air control valve or
idle air control motor is possible

same thing but diff parts stores call it diff name

Posted on Aug 26, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2003 f 250 super duty truck five beeps five times

5 beeps 5 times - Ford Truck Enthusiasts Forums > ... > Super Duty & Heavy Duty
Jan 2, 2009 - 5 beeps 5 times Super Duty & Heavy Duty. ... 2003 F250 4x4 CC V10 4" Procomp, all white beauty "list of previous owned Fords much to long to ... Beeping under my dash
Jun 17, 2012
Getting these strange beeps from Dashboard
Nov 13, 2010
beeping noise
Dec 22, 2009
5 beep tones 2000 f250

Oct 14, 2015 | 2003 Ford F-250 Super Duty

1 Answer

2001 f250 v10 dies while running reestarts ok

If this is happening when you foot is off the throttle, try this...........

First eliminate all vacuum or air leaks in the system (very important)

. You may have a bad IAC ( idle air control) but try cleaning the throttle body first. Remove the intake snorkel, have someone hold the throttle wide open for you and scrub the back side of the throttle plate and surrounding bore with an old tooth brush and some carb cleaner. Be sure to spray some into the small holes next to the throttle plate. That should help stabilize the idle. If it still has a problem, replace the IAC.

Aug 06, 2014 | 2002 Ford F250 Super Duty SuperCab

1 Answer

Have a Ford f250 super duty that will start then cut off

Check mass air sensor, clean it. make sure intake tube is attached. Mine fell off one time and did the same thing.

Aug 28, 2013 | 2002 Ford F250 Super Duty SuperCab

1 Answer

Ford F250 2002 7.3 Diesel won't start

check engine immobiliser and crank position sensor . Run fault codes and replace faulty units.

Apr 04, 2013 | Ford Cars & Trucks

1 Answer

2002 Ford F250 v10 dies at idle

You can try several things. I am going to say it is probably the TPS-Throttle Position Sensor. This is located on the airhorn and usually on the drivers side. The butterfly shaft connects to the TPS and the TPS is held on by 2 screws and has 1 electric connector. If this cures your problem you are okay, however if you still want more RPM, the opposite side of the butterfly flap has a set hex screw which will allow more RPM like a carb.

There is usually an elongnated slot on the TPS which can be slightly adjusted to help.

You can get a free scan at Autozone or Oreillys and see if anything coded.

Sep 28, 2009 | 2002 Ford F250 Super Duty SuperCab

2 Answers

F350 V10 starts but falters and dies

have put a new fuel regulator on this truck if you done everything else try that

Jan 11, 2009 | 2003 Ford F350 Super Duty DRW SuperCab

2 Answers

2003 F250 super duty 4x4 no throttle

did you check the linkage?. if the linkage is ok your tps(throttle position sensor is bad. you need to replace it. it is located on the throttle body housing is black in color and has (2) bolts that hold it in place there is a weatherproof plug with (2) wires. hope this helps yah out. please rate this

Sep 01, 2008 | 2003 Ford F250 Super Duty Crew Cab

1 Answer

Engine light on dashboard

the sensor bank is the exaust manifold the # 1 is left side #2 is right side. they should be located right after the exaust manifold on the pipe it's self. all you have to do is unplug them and remove for replacement.

Aug 28, 2008 | 2003 Ford F250 Super Duty Crew Cab

Not finding what you are looking for?
2000 Ford F250 Super Duty Crew Cabs Logo

1,321 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides