Question about 2003 Volvo S60

1 Answer

How do I remove my Volvo S60 2000 Rear Brake discs

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

You have to release the hand brake as the shoes are inside the disc and remove caliper its a straight forward job have you done it yet

Posted on Sep 19, 2009

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 57 Answers

SOURCE: Cant remove rear break disc

The reason is that the the emergency brake drums are on the inside of the disc. It will probably take a lot of force or a rubber malet to get it off!

Posted on Sep 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1992 volvo brakes rear brakes started smoking. There was also a burning smell? Any ideas?


rear disc can be activated by bad fluid heating up. If there is moisture in the brake fluid it can make steam and cause the rear brakes to partially engage. did this one myself at the brake shop.

Apr 15, 2013 | 1992 Volvo 240

1 Answer

How to remove rear rotor after wheel is off


Disc Removal
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552).
1.Remove the brake caliper bolts (2W303).
2.Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220aca3301.gif
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and contract(push back to allow clearance) the parking brake shoe and lining.
  2. Remove the rear brake disc.

Feb 11, 2010 | 1998 Mercury Mountaineer

1 Answer

How do remove rear rotors on 2004 ford sport trac


Caliper removal

  1. Disconnect the brake hose.
  2. Remove the bolt.
  3. Disconnect the rear wheel brake hose (2A442).
  4. Remove the copper washers and plug the brake hose.
  1. s2r~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
    Remove the rear disc brake caliper (2552).
    1. Remove the brake caliper bolts (2W303).
    1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
  1. Inspect the rear disc brake caliper for leaks.
    • If leaks are found, disassembly is required. Refer to Caliper in this section.
--------------------------------------------------------------------------------------------
Disc Removal and Installation
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552). For additional information, refer to Caliper in this section.
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and retract the parking brake shoe and lining.
    Remove the rear brake disc.
  1. s2r~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use a hub-mount brake lathe if necessary to machine the rear brake disc. For additional information on machining brake discs, refer to Section 206-00 .
    Measure the rear brake disc, and resurface as necessary. Install a new rear brake disc if beyond specification.
---------------------------------------------------------------------------------------------
Installation
  1. s2r~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent interference with rear disc brake caliper operation, install only the correct caliper bolt.
    NOTE: Make sure the stainless steel shoe slippers are correctly positioned. Install new slippers if worn or damaged.
    NOTE: When installed, the locator notch on the brake pads will be located at the upper end of the rear disc brake caliper.
    Install the rear disc brake caliper.
  1. Install the rear wheel brake hose.
    • Connect the brake hose and install the caliper flow bolt.
      • Use new copper washers.
  1. Bleed the disc brake caliper. For additional information, refer to Section 206-00 .
  1. Install the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Verify correct brake operation.

Dec 17, 2009 | 2004 Ford Explorer Sport Trac

1 Answer

Brake rotors need to be resurfaced,explain best way to remove rotors from vehicle.


front ones remove wire clip remove bolts from caliper hang caliper out of way remove pads remove 2 bolts from pad carrier put to one side remove 2 disc retaining bolts remove disc may need hammer clean hub flange with wire brush fit new disc clean pad carrier and refit fit new pads put some copper grease on back of pads push in caliper piston slowly using large grips or g clamp fit and secure caliper pump up brake pedal check brake fluid level do other side for rear brakes see my solutions

Dec 01, 2009 | 1999 Volvo S80

1 Answer

Rear brake disc needs replacing


with car on stands use punch to remove pad retaining pins pull out pads can be tight remove 2 calliper retaining bolts move calliper away from disc remove disc retaining bolts remove disc check hand brake shoes and clean look for adjuster between shoes if it has one back it of some models just have hand brake cabel adjustment clean and fit new disc secure adjust hand brake shoes using screw driver through wheel bolt hole clean refit calliper slowley push back calliper pistons fit new pads refit retaining pins do other side pump up brake pedal check and adjust handbrake if neededcheck brake fluid level

Oct 20, 2009 | 2001 Volvo S80

1 Answer

Cant remove rear break disc


The reason is that the the emergency brake drums are on the inside of the disc. It will probably take a lot of force or a rubber malet to get it off!

Jun 01, 2009 | 2003 Volvo S60

3 Answers

How do i remove the rear rotor on a 2000 ford explorer xlt


  1. Disconnect the brake hose.
  2. Remove bolt.
  3. Disconnect the rear wheel brake hose (2A442).
  4. Remove the copper washers and plug the brake hose.
  5. Disconnect the brake hose.
    1. Remove bolt.
    1. Disconnect the rear wheel brake hose (2A442).
    1. Remove the copper washers and plug the brake hose.
      syn~us~en~file=dh0472a.gif~gen~ref.gif
    1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
      Remove the rear disc brake caliper (2552).
      1. Remove the brake caliper bolts (2W303).
      1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
      syn~us~en~file=gh0619a.gif~gen~ref.gif
    1. Inspect the rear disc brake caliper for leaks.
      • If leaks are found, disassembly is required. Refer to Caliper in this section.
      syn~us~en~file=gh1478a.gif~gen~ref.gif
    Installation
    1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent interference with rear disc brake caliper operation, install only the correct caliper bolt.
      NOTE: Make sure the stainless steel shoe slippers are correctly positioned. Install new slippers if worn or damaged.
      NOTE: When installed, the locator notch on the brake pads will be located at the upper end of the rear disc brake caliper.
      Install the rear disc brake caliper.
      syn~us~en~file=dh0528a.gif~gen~ref.gif
    1. Install the rear wheel brake hose.
      • Connect the brake hose and install the caliper flow bolt.
        • Use new copper washers.
      syn~us~en~file=gh0621a.gif~gen~ref.gif
    1. Bleed the disc brake caliper. For additional information, refer to Section 206-00 .
    1. NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.
      Install the wheel and tire assembly. For additional information, refer to Section 204-04 .
    1. Verify correct brake operation.
  6. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
    Remove the rear disc brake caliper (2552).
    1. Remove the brake caliper bolts (2W303).
    1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
  1. Inspect the rear disc brake caliper for leaks.
    • If leaks are found, disassembly is required. Refer to Caliper in this section.
Disc Removal
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552). For additional information, refer to Caliper in this section.
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and contract the parking brake shoe and lining.
    Remove the rear brake disc.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use a hub-mount brake lathe if necessary to machine the rear brake disc.
    Measure the rear brake disc, and resurface as necessary. Install a new rear brake disc if beyond specification.
--------------------------------
Installation
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent interference with rear disc brake caliper operation, install only the correct caliper bolt.
    NOTE: Make sure the stainless steel shoe slippers are correctly positioned. Install new slippers if worn or damaged.
    NOTE: When installed, the locator notch on the brake pads will be located at the upper end of the rear disc brake caliper.
    Install the rear disc brake caliper.
  1. Install the rear wheel brake hose.
    • Connect the brake hose and install the caliper flow bolt.
      • Use new copper washers.
  1. Bleed the disc brake caliper. For additional information, refer to Section 206-00 .
  1. NOTE: If equipped with air suspension, reactivate the system by turning on the air suspension switch.
    Install the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Verify correct brake operation.

May 06, 2009 | 2000 Ford Explorer

1 Answer

Rear brake rotor replacment


206-04: Rear Disc Brake 2000 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Disc Removal
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552). For additional information, refer to Caliper in this section.
  2. Disconnect the brake hose.
  3. Remove bolt.
  4. Disconnect the rear wheel brake hose (2A442).
  5. Remove the copper washers and plug the brake hose.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
    Remove the rear disc brake caliper (2552).
    1. Remove the brake caliper bolts (2W303).
    1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
  1. Inspect the rear disc brake caliper for leaks.
    • If leaks are found, disassembly is required. Refer to Caliper in this section.
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and contract the parking brake shoe and lining.
    Remove the rear brake disc.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use a hub-mount brake lathe if necessary to machine the rear brake disc.
    Measure the rear brake disc, and resurface as necessary. Install a new rear brake disc if beyond specification.

Mar 28, 2009 | 2000 Ford Explorer

2 Answers

Brake pad change


yes, the process is the same. the ABS sensor isn't physically attached to any of the brake components, so don't sweat it. (please rate my answer)

Feb 02, 2009 | 2002 Volvo S40

1 Answer

Brake vibration problem


could be a bad outer tie rod end or lower ball joint on the front suspension, to check jack up wheel (suspension supported) grasp tire and move back and forth, if you feel loosness you have a worn component. if there is no looseness then you have either an bad wheel bearing (excessive runnout) or defective rotors

did you replace All discs front and rear? if not , replace the ones that you previously didnt

Oct 17, 2008 | 1998 Volvo S70

Not finding what you are looking for?
2003 Volvo S60 Logo

Related Topics:

273 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...