Question about 2000 Plymouth Neon

Open Question

Windshield Wipers go on their own!

I assume there's something with the wiring going on because the windshield wipers (ww) go on their own. They turn on when I have the headlights on and when I have the a/c on. Even more so when both the headlights and a/c are on. Not knowing what else to do, my bf took the ww fuse out and showed me how to put it back when it rains so now i just remove and replace the fuse whenever necessary.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jmassengill
  • 345 Answers

SOURCE: Windshield Wipers

Under the cowl (it is a plastic piece that the windshield wipers come out of) are the wiper arms that connect to the wiper motor. There are plastic parts that hold the wiper arms to the wiper motor. Lots of time these plastic parts dry out and break and the wiper arm will fall off the wiper motor. I would bet if you tried to move one of the wipers by hand both of them would move with little resistance. This would tell me that the wiper arms are disconnected from the wiper motor. The parts to fix this are easy to get. I know the motormite HELP line of parts used to have the plastic bushings to fix this problem.

Posted on Nov 23, 2008

lancer721
  • 229 Answers

SOURCE: 1999 plymouth voyager front windshield wipers not working proper

Sure pull the cover off the arm at the base(by the bottom of the windshiel) under that you will find a bolt. Unbolt the arm and pull it off then adjust both arms so that they do not entangle at the high point. You can turn on the wipers and when they reach the high end quickly shut off ignition they will stop at this position so you can adjust them, This is what we would do at the shop for about 200 bucks. Take your time and be sure to tighten everything up when you're don and you will do great. Have fun.

Posted on Nov 29, 2008

  • 120 Answers

SOURCE: windshield wipers don't work

check the fuse then the relay then the switch.

Posted on Dec 25, 2008

  • 22 Answers

SOURCE: Wiper don.t work

Remove the wiper arms amd the panel between the hood and the windshield. There are teflon bushings on the actuater arms that wear out, they are cheap and available from the dealer but can be tricky to install because of the limited access.

Posted on May 09, 2009

  • 4088 Answers

SOURCE: windshield wipers come on by themselves

We had a '96 Dodge Caravan that did the same thing when it was nearly new, but never did find the problem. Several mechanics said that these cars had bad local grounding problems, but never proved it. By the time Chilton's repair manual had come out for this car, the problem had fixed itself (nearly 150,000 miles by then). There is an auto-park switch on the wiper motor that may be mis-adjusted which could cause intermittent spontaneous operation. The motor can be accessed by removing the cowl plate just in back of the hood. The body computer which controls the wiper motor is located on the passenger side front wheel well near the washer reservoir. Check around this for any ground wire connections that could be cleaned and re-tightened. Remove the screws that hold the body computer to the panel as they may have become rusted from wheel splash--wire brush the threads and apply heavy grease. Reinstall them firmly. The only other possibility is metal junk in the wiper control switch. Hope this helps!

Posted on Feb 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

2003 Impala wipers don't work have power and new motor but nothing moving when on


Depending on what your trying to do with wipers, I'd want to see voltage on the gray and or purple wire. See the black wire at the bottom that is ground, a good ground is a must. Hey Jeff, I'm not trying to bug you. If I spend time trying to look up info, I'm going to post it. I don't care if the question has already been answered. Have a good day.
wipers-ersrqsmaeg3uuiau2mcjzkj1-1-0.jpg

Aug 05, 2017 | Cars & Trucks

1 Answer

Why is my windshield wipers running in the off position, it's like they are running in the intermittent position, but it's in the off position.


When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Schematic Reference: Wiper/Washer Schematics


1

Did you review the Wiper/Washer System Description and Operation and perform the necessary inspections?
Go to Step 2
Go to Symptoms - Wiper/Washer Systems

2

  1. Turn the ignition ON.
  2. Turn the windshield wiper/washer switch OFF.
Are the windshield wipers always on?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

3

Disconnect the windshield wiper/washer switch connector.
Are the windshield wipers always on?
Go to Step 4 if yes
Go to Step 7 if no

4

  1. Disconnect the windshield wiper motor connector.
  2. Test the windshield wiper switch signal 1 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 5

5

Test the windshield wiper switch signal 2 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 6

6

Test the windshield wiper motor high speed circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 9

7

Inspect for poor connections at the windshield wiper/washer switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 8

8

Replace the windshield wiper/washer switch. Refer to Windshield Wiper and Washer Switch Replacement - On Vehicle in Steering Wheel and Column.
Is the repair complete?
Go to Step 11
--

9

Inspect for poor connections at the windshield wiper motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10

10

Replace the windshield wiper motor. Refer to Windshield Wiper Motor Replacement .
Is the repair complete?
Go to Step 11
--

11

Operate the system in order to verify the repair.
Did you correct the condition?
The Wiper / Washer System consists of the following components:
?€¢
Windshield wiper / washer switch


?€¢
Windshield wiper system module / motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
Instrument panel cluster (IPC)


?€¢
ACC 15-amp fuse


?€¢
WSW 30-amp fuse

Jan 04, 2016 | 2002 Pontiac Bonneville

1 Answer

2007 Pontiac g6 wipers stay in upright position


Hey Derek , here is how the wipers park position is suppose to work !
Windshield wiper motor park operation is controlled by the body control module (BCM) using an input from the park switch within the wiper motor assembly. The BCM monitors the windshield wiper motor park switch circuit to determine if the windshield wiper blades are at the bottom of the glass. The circuit will be pulled to ground by the wiper motor park switch while the windshield wiper motor is operating. When the wiper switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the BCM will continue to operate the motor until the wipers reach the park position. If the ignition is turned OFF while the wipers are in mid-cycle, the wipers will stop immediately where they are. The BCM will park the wipers the next time the ignition is turned ON.
The wipers will not park when they are commanded ON and OFF with a scan tool. The BCM will park the wipers the next time the wiper switch is turned ON and OFF.
The BCM provides stall protection for the wiper motor by monitoring the park switch. If the park switch does not transition for 3 seconds while the wipers are operating, the BCM will assume that the wiper motor is stalled, and will de-energize the wiper relay until the wiper switch is cycled OFF and ON again.
Check for a voltage signal on the yellow wire at the wiper motor assembly , this is signal to the BCM ! If there is no signal you need to replace the windshield wiper motor assembly ? If there is a signal need to have Tech 2 scan tool hooked up to see if The BCM is the problem ! Relay #39 an #40 are the high an low wiper relays in the under hood fuse block ! Do you have a volt meter ,do you know how to do electrical testing ?

Sep 21, 2015 | Pontiac Cars & Trucks

1 Answer

Car does not turn off after changing fuse


car stays, on, does that mean engine will not shut down.
or mean the wipers stay on, after turning them off
1:yes, wiper, bad internal wiper switch, (bad wiper motor)
2: no:?
wiring hacks (after market installs of something gone worn)
bad igniton switch.

Dec 12, 2013 | Acura Integra Cars & Trucks

1 Answer

Need to get a programmer dont know where its at


  • Windshield Wipers Continue to Run When Turn Signal and Windshield Wiper Switch Are Turned OFF
  • Damaged turn signal and windshield wiper switch .
  • Damaged windshield wiper motor .
  • Damaged windshield wiper control module.
7fd52e7.gif
efd7dbe.gif
Pin Number Circuit Circuit Function 1 57 (BK) Wiper Motor Ground (Park) 2 28 (BK/PK) Wiper Module to Wiper Motor (Park Switch) 3 65 (DG) Wiper Motor Power (Park Feed) 4 61 (Y/R) Wiper Motor Common (RUN) 5 56 (DB/O) Wiper Motor LO 6 58 (W) Wiper Motor HI
Windshield Wiper System The windshield wiper system consists of :
  • Windshield wiper motor (17508) (F-type).
  • Washer system.
  • Windshield wiper control module.
  • Turn signal and windshield wiper switch (13K359).
The windshield wiper control module is:
  • Located at the instrument panel fuse panel.
The windshield wiper motor is:
  • Attached to the cowl top extension (021A36) .
  • Connected to windshield wiper mounting arm and pivot shaft (17566) .
The turn signal and windshield wiper switch features a:
  • Rotary wiper switch.
  • Push type washer actuator.
OFF/Low/High Speed
  • Has a two-speed, permanent magnet, three brush electric windshield wiper motor .
  • The windshield wiper motor has a brush rigging that permits selection of low or high speed.
  • When the turn signal and windshield wiper switch is in the LO position, the common brush and the blue/orange wire brush are used, and the windshield wiper motor operates at low speed.
  • When the turn signal and windshield wiper switch is in the HI position, the common brush and the white wire brush are used.
  • In HI position, electric current will bypass a portion of the armature winding causing the windshield wiper motor to operate faster.
  • When the turn signal and windshield wiper switch is moved to the OFF position, the windshield wiper motor will continue at low speed until the park switch outer contacts open.
  • When the park switch contacts open, the windshield wiper motor stops in the park position.
Interval
When the turn signal and windshield wiper switch is in the interval position:
  • The wipers make single wipes separated by pauses.
  • The rotary switch is on the end of turn signal and windshield wiper switch .
  • The length of the pause can be set from approximately 1 to 17 seconds.
  • Length of pause decreases as the rotary switch is rotated away from off.
  • Length of pause increases as the rotary switch is rotated toward off.
While in the interval wiper mode:
  • It is normal to hear a slight click at the beginning of each on/pause cycle. NOTE: When using interval wipers, the first wipe may not occur until after a pause of up to 17 seconds.

May 27, 2009 | 1994 Ford Mustang

1 Answer

Windshield wipers won't work right


The windsheild wiper relay might be stuck or broken. Try tapping it with something or replace it. Could also be the the switch (lever that you control the wipers with) i hope this helps and good luck with diagnosing your problem.

Feb 21, 2009 | Ford Taurus Cars & Trucks

1 Answer

Windshield wipers won't work 1997 ford taurus


i have just got a 1997 taurus an they have a ground wire going from the ww motor to one of the mounting bolts,if i unhook it the wipers wont work but as long as it is hooked up they work fine

Jul 18, 2008 | 2005 Ford Taurus

Not finding what you are looking for?
2000 Plymouth Neon Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...