Question about 1996 Toyota Tacoma

Open Question

Need a timing chain diagram for a 96 toyota tocoma 2.4

Need timing chain diagram

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 19 Answers

SOURCE: nee the timing position or diagram for timing for toyota celica

phone toyota and they will tell you :) p.s timing belt

Posted on Nov 24, 2009

Ad
  • 32 Answers

SOURCE: I need a diagram for the timing chain and marks

this should help you bro

Posted on Apr 02, 2010

jturcotte
  • 8841 Answers

SOURCE: I was wandering how to

Hi, the procedures below are pasted from autozone.com. I have added information to the steps to explain and emphasize certain points. Please let me know if you have any questions, and thanks for using FixYa.

3VZ-E Engine

See Figures 1 through 10


WARNING This procedure requires tools which may not be in your tool box. Pulley extractors and a counter-holding bar are required. Do not attempt the procedure without these tools available.
jturcotte_714.gif

Fig. Fig. 1: Exploded view of the 3VZ-E engine timing belt routing

  1. Disconnect the negative battery cable and drain the coolant.
  2. Remove the radiator and shroud.
CAUTION When draining coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain coolant into a sealable container. Coolant may be reused unless it is contaminated or several years old.
  1. Remove the power steering belt and pump.
  2. Remove the spark plugs.
  1. Disconnect the air hoses at the air pipe.
  2. Disconnect the water bypass hose at the air pipe and then remove the water outlet.
  3. Remove the air conditioning belt. Remove the alternator drive belt, fluid coupling, guide and fan pulley.
  4. Disconnect the high tension cords and their clamps at the upper timing belt cover and then remove the cover and its three gaskets.
  5. Rotate the crankshaft pulley until the groove on its lip is aligned with the 0 on the lower timing belt cover. This should set the No. 1 cylinder at TDC of its compression stroke. The matchmarks on the camshaft timing pulleys must be in alignment with those on the upper rear timing cover. If not, rotate the engine 360° (one complete revolution).
  6. Remove the power steering pulley. Use the counter-holding tool to aid in removal of the crank pulley bolt. Remove the crankshaft pulley using a puller.
  7. Remove the fan pulley bracket and then remove the lower timing belt cover.
  8. If the belt is to be reused after removal, mark an arrow on the belt showing the direction of rotation. Make matchmarks on the side of the belt and the flanges of each pulley. These marks will be important at reassembly.
jturcotte_715.gif

Fig. Fig. 2: Mark the position of the belt if it is to be reused

  1. Remove the timing belt guide and remove the tension spring.

jturcotte_716.gif

Fig. Fig. 3: Remove the tension spring

  1. Loosen the idler pulley bolt and shift the idler to the left as far as it will go. Temporarily tighten the bolt and release tension from the belt. Slide the belt off the pulleys.

jturcotte_717.gif

Fig. Fig. 4: Move the tensioner all the way to the left, then tighten the bolt

  1. Protect the belt at all times. Do not bend, twist or turn the belt inside out. Do not allow the belt to contact oil, grease or water.
  2. Examine the belt closely for cracking, loose teeth, separation or wear on the edges. If the belt is not virtually perfect, replace it.
  3. Check the idler pulleys for smoothness of rotation. Inspect the tension spring; correct length is 2.15 in. (54.6mm).
jturcotte_718.gif

Fig. Fig. 5: Measure the length of the tension spring

To install:

  1. Make absolutely certain the marks on the camshaft pulleys are aligned with the marks on the rear belt cover. Check the lower belt pulley; align its mark with the mark on the oil pump housing.
  2. Install the timing belt onto the cam pulleys, idler pulley, water pump pulley and crank pulley. If reusing the original belt, take great care to align all the marks made before removal. Then, when installing the belt, keep belt tension first between the camshaft gears and then from the exhaust cam gear to the crankshaft gear--this is critical to the timing. All slack should be between the crankshaft gear and the intake cam gear, until the tensioner is released to take out the slack.

jturcotte_719.gif

Fig. Fig. 6: Inspect the belt for any signs of damage

  1. Loosen the idler pulley bolt; move it as far to the right as it will go. Temporarily tighten it in position.
  2. Install the tension spring. Loosen the idle pulley bolt to the point that the idler pulley moves with the tension of the spring.
  3. Temporarily install the crankshaft pulley bolt. Turn the crankshaft clockwise two complete revolutions from TDC to TDC. Check that the mark on each pulley aligns exactly with the matching marks on the covers or housing.
jturcotte_720.gif

Fig. Fig. 7: Always turn the engine in a clockwise direction



jturcotte_721.gif
Fig. Fig. 8: After rotating the engine, ALL the timing marks must align perfectly

  1. Tighten the idler pulley bolt to 27 ft. lbs. (37 Nm).
  2. Remove the crank pulley bolt. Install the belt guide on the crankshaft pulley. The cupped side faces outward.

jturcotte_722.gif

Fig. Fig. 9: Install the belt guide with the cupped side out

  1. Install the bottom belt cover with the two gaskets.tighten the bolts to (5 Nm).
  2. Install the fan pulley bracket and tighten it to 30 ft. lbs. (41 Nm).
  3. Install the upper cover and tighten the bolts 48 inch lbs. (5 Nm).
  4. Position the crankshaft pulley so the groove in the pulley is aligned with the woodruff key in the crankshaft. Tighten the bolt to 181 ft. lbs. (245 Nm).
  5. Install the fan pulley, guide, fluid coupling and alternator drive belt. Adjust the belt tension.
  6. Install the power steering pump and belt. Install the air conditioning belt. Adjust the belt tension.
  7. Apply sealant to the contact surface of the water outlet. Install the water outlet and connect the bypass hose. Connect the air hoses.
jturcotte_723.gif

Fig. Fig. 10: Apply sealant to the water outlet before installation

  1. Install the spark plugs.
  2. Install the radiator and fill with coolant.
  3. Road test the vehicle. Check for leaks. Recheck the ignition timing.

Posted on Jan 02, 2011

johnjnail
  • 1702 Answers

SOURCE: I need a diagram for

on the chain you will find 3 different coler links these are the timing marks line the links up with the dots on the sprockets.


johnjnail_63.jpg

Posted on Jun 20, 2011

GeoffW1
  • 3961 Answers

SOURCE: i need a digram for 2001 toyota corolla replacing timing chain & tensioner

I have them for a 2004 Corolla, which should be very similar. Post an email and I'll send them. Open a one-time account if you want with Gmail or Yahoo.

Posted on Jan 21, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Toyota tocoma is blowing the fusible link fuse when I put the positive cable on


What is the model year? I'd have to look at wiring diagram to see what that fusible link fuse controls? Maybe there is a short to ground, somewhere? I can't tell you much w/o looking at wiring diagram?

Jan 26, 2018 | Toyota Cars & Trucks

1 Answer

How to set timing on toyota quantum 2,7


2007 , not in USA>

Toyota Quantum (South Africa)
wiki says.
2TR-FE 2,700 cc petrol engine

so google 2TR-FE, or read your FSM.
It features DOHC, 16 valves and VVT-i

changing chain are not easy.
lots of mistakes can blow an engine. if you let it snap.

our 2.7L in the Tacoma, is CHAIN drive.
im at alldata.com
58 steps and 25 photos. for just removal.
how'd you like that, here,
it take me 2 hours to get this , host it and link it.
why would any one do that.
why not pay $15 like we do.. and discounted here.
we dont have your car so pick 07 tocoma , it has same engine.
http://www.scantool.net/software/alldata-diy-1-month-subscription.html

but your body is different so many steps will vary.
why no go to toyota and buy the FSM for your car and your country.
for best play

Feb 20, 2014 | 2007 Toyota Quantum 2.7

1 Answer

How to replace timing chain on Toyota hiace 2007 diagram


hi how i can change timing chain toyota hiace

Jan 15, 2013 | Cars & Trucks

1 Answer

I need a diagram to set the time on the timing chains of a 1997 Toyota Tacoma 2.7L, 4 cylinder, 3RZ. It is out of time. I need a diagram on how to time the timing chains. Markings needed to set time....


Please contact me at sj196653@yahoo.com I will send you full pictures and literature on this subject.After you rate my solution i no longer give out my time and resources for a later rating on my solution which they did not even go back and give me a number 1 rating sorry. This is why i do this for my ratings.

Apr 14, 2012 | 1997 Toyota Tacoma

1 Answer

Need to view vidao of calper rebuild on 2004 toyota tocoma 2 wheel dr. prerunner v6eng.


Very informative and interesting post.It is really a big help. Thank you so much for sharing it with us.
custom-t-shirts
customized shirts

Nov 09, 2011 | 2004 Toyota Tacoma

1 Answer

Replacing a timing chain on a 96 grand am. need a


it is a good idea to get a haynes repair book on your type of car it will give u step by step how to do it,,it is not much,,,

Apr 24, 2010 | 1996 Pontiac Grand Am

2 Answers

HOW TO SET TIMING ON 96 TOYOTA CAMRY 2200 MOTOR


Click on the following free direct Link. It has the Timing: Pulley, Belt and Mark Diagrams for your 1996 Toyota Camry. Plus additional Instructional and Directional Diagrams.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1996/make/toyota/model/camry/1996_toyota_camry_timing_belt_diagram_marks.htm

Mar 28, 2010 | 1996 Toyota Camry

2 Answers

I need a wiring diagram for fog lights oem to my toyota


The link below is a Typical fog lamp / driving lamp hookup. Keep in mind that in most states, for these lamps to be 'legal' (and thus pass inspection), you must wire them such that:

1. You can cut them off (in other words, there must be a switch installed to turn them off)

and

2. They may only be operated with the low beams. (therefore, you must power your on/off switch from the low beam circuit)

http://www.accessconnect.com/fog_driving_lights_wiring.htm

Feb 28, 2009 | 2005 Toyota Corolla

Not finding what you are looking for?
1996 Toyota Tacoma Logo

Related Topics:

350 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

83940 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22441 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...