Question about 1995 Ford Club Chateau

1 Answer

Shifts great 1 to 2 than stays in 2 will not shift to 3 or 4th

1994 ford bronco

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 30 Answers

Need trans code could be speed senser could be pcm could be shift sol

Posted on Feb 11, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 91 ford bronco 5.0 electric shift, why wont transmission downshift? it upshifts fine.


what does the tps (throttle position sensor) cause your bronco to ...

www.fullsizebronco.com > ... > 1980-'96 Bronco Tech
Jun 20, 2010 - 19 posts - ‎10 authors my 1994 bronco with the 5.0 and 131k original miles, the check engine ... not want to start up? what does a bad throttle position sensor cause? ... you're e4od transmission'sshift points use TPS measurments

Sep 12, 2015 | Ford Cars & Trucks

1 Answer

1986 ford bronco 4x4s edit Bauer edition 302


I dont think that engine would run at 300 rpm at 55 mph.

Sep 03, 2014 | 1986 Ford Bronco

1 Answer

How to put bronco in 4x4 low


With the engine running, put your foot on the brake and shift the transmission to neutral. Now move the transfer case shifter forward till it stops then push it down towards the floor and forward again. You should now be in low range

Nov 19, 2013 | 1994 Ford Bronco

1 Answer

1990 Ford Bronco II manual transmission extremely hard to shift will not go into reverse


90 Ford Bronco II: You have to put it in whichever gear you want it in before you start it or it wont shift at all. Then once you are going its extremely hard to shift into the other gears. Reverse is the only gear that sounds like its grinding.

Aug 16, 2013 | 1990 Ford Bronco II

1 Answer

My ford bronco doesnt move idles great gears go in but wont movee is it the clutch or the fluids


For this car, it can be really pricy or you can take my advise. I would recommend that you remove the 1 or 2 screws located on the reverse side of the shifter!. once you do this, you basically deactivate a safety device that is preventing you from shifting your car into gear! The safety device basically will not allow you to shift until you press firmly on the breaks and the key is installed. TAKE IT FROM AN EXPERT who has been there done that hundreds of times. you can find the screws on the reverse side of the shifter, just feel for them with your fingers.

Jan 26, 2011 | 1984 Ford Bronco II

1 Answer

Dies when shifted in to drive 94 bronco


pcm problem. the EEC has some control on the transmission. PCM- power train control module. EEC IV Electric engine control. they both play together. Check engine light on

Sep 28, 2010 | 1994 Ford Bronco

1 Answer

I have a 1992 Ford Bronco and it began to hesitate tonight while driving. I put the gear in low and now I dont know how to get the truck back into the correct gear. Im not familiar with the floor gears


look at the driver side visor the shift pattern is printed there. it should be also on the shift lever itself . I think 2 wheel high is all the way forward then back 1 is neutral back 1 more is 4w low and all the way back is 4w high

Oct 01, 2009 | 1990 Ford Bronco

2 Answers

1992 ford bronco shifting


get the transmission solenoid checked out

Jun 07, 2009 | 1992 Ford Bronco

1 Answer

Transmission does not shift at the proper RPM. The engine over revs before it shifts. Does Vacuum or electric shift these transmissions? If it is electric, does it have a relay?


At your Bronco's age, the vacuum hoses are suspect. The plastic ones break, the rubber ones crack and leak. There is a specific one to the transmission to control shifting, usually. Some vehicles have a modulator valve on the transmission; when it fails you will see white smoke at the tailpipe and you will lose trans fluid. Check all the vacuum lines, large and small. A vacuum gauge is a great tool, it will tell you a lot about an engine.

Apr 25, 2009 | 1992 Ford Bronco

1 Answer

1986 ford bronco 302 AOD - How do I know if it shifts into OD?


2500rpm is about right, it'd be about 3k in D

Dec 02, 2008 | 1986 Ford Bronco

Not finding what you are looking for?
1995 Ford Club Chateau Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...