Why dont i have power steering? - 2002 Jeep Liberty

bleed power steering with engine off pour power steering fluid in the power steering reservoir until fluid stay at full mark on powersteering pump dip stick.wait few minutes then check powersteering fluid again if low add little more when fluid level stop dropping crank vechicle turn steering left to right with out a stop turn steering wheel all the way to the left to all way to right for minute until air bubbles leave the powersteering fluid. when steering wheel feel normal stop engine check check power steering fluid should be at full hot mark if fluid level dont drop air is out the system. dont overfill powersteering reservoir if so you will blow front seal.dont drive vechicle if steering dont feel normal have vechicle towed in garage.

to bleed power steering, with front wheels off ground slightly with front wheels pointing straight ahead.engine off. remove power steering filler cap.add power steering until fluid level stop dropping,wait couple minutes and wait, add fluid until level stay at full cold mark on power steering cap dip stick. dont over fill.when fluid level stop dropping, start vechicle,let it idle few minutes. see if fluid level drop if so add more fluid full cold mark.then turn steering all the way to left and right with out hitting a stop.turn steering wheel several times, then turn front wheels pointing forward check power steering fluid level.if power steering fluid level stop dropping air should be out of system, if steering turning wheel dont turn smoothly and power steering fluid look light tan color air getting in the system.check all power steering lines to rack and power steering pump for leaks.be sure you replaced all the power steering lines with new o rings if not you will get a leak.if you find a leak, you need to fix the leak and bleed system again.dont drive vechicle if your steering dont feel right,have vechicle towed to a garage.

there is no power steering filter. dont even worry about any power steering filter. those cars dont have any power steering issues.

FIRST OF ALL TURN OFF RADIO REMOVE NEGATIVE BATTERY CABLE. THEN REMOVE POWER STEERING PUMP FLUID FROM POWER STEERING PUMP.USING A HAND PUMP SIPHON. BE CAREFUL DONT GET POWER STEERING FLUID ON CAR PAINT IT WILL DAMAGE PAINT JOB.PUT A DRAIN PAN UNDERNEATH CAR TO CATCH POWER STEERING FLUID THEN DISCONNECT POWER STEERING PUMP LINES.REMOVE POWER STEERING PUMP ADJUSTER BOLT AND MOUNTING BOLT.REMOVE POWER STEERING PUMP.MOST OF THE TIME NEW POWER STEERING PUMP DONT HAVE DRIVE PULLEY ON IT SO TAKE TO A MACHINE SHOP THE WILL REMOVE PULLEY FROM OLD PUMP AND PRESS ON THE PULLEY TO NEW POWER STEERING PUMP.BESURE TO BUY NEW O RINGS TO END OF PRESSURE LINE.ONCE NEW POWER STEERING PUMP HAS PULLEY IN PLACE AND YOU HAVE NEW O RING FOR HIGH PRESSURE LINE.INSTALL NEW PUMP.ADJUST BELT TENSION.NOW BLEED POWER STEERING PUMP WITH FRONT WHEELS POINT STRAIGHT A HEAD POSITION.POUR POWER STEERING FLUID IN PUMP UNTIL FLUID LEVEL ON COLD MARK ON POWER STEERING PUMP DIP STICK.KEEP ADDING FLUID UNTIL FLUID STOP DROPPING. START THE ENGINE LET IT RUN AT IDLE ADD MORE FLUID IF DROPS KEEP FLUID ON FULL COLD MARK.ON DIP STICK TURN OFF ENGINE.CHECK TO MAKE SURE POWER STEERING PUMP NOT LEAKING AT THE LINES THEN.SAFELY RAISE SUPPORT FRONT OF THE VECHICLE WITH JACK STANDS. MAKE SURE VECHICLE ON SOLID LEVEL GROUND CHECK.FLUID LEVEL MAKE SURE AT FULL COLD MARK. NOW START ENGINE.LET IDLE MINUTE.THEN TURN STEERING WHEEL ALL THE WAY TO THE LEFT TO RIGHT SEVERAL TIMES WITH OUT STOPPING IT IN PLACE. CHECK POWER STEERING FLUID WHEN FLUID LEVEL STOP DROPPING.AND FLUID IS NOT A TAN COLOR WHICH MEAN LOTS OF AIR IN SYSTEM. TURN OFF CAR UNTIL AIR BUBBLES DISAPPEAR.CHECK FLUID LEVEL BLEED POWER STEERING AGAIN. DONT DRIVE VECHICLE UNTIL STEERING FEEL NORMAL.IF FLUID REMAIN TAN WITH AIR BUBBLES CHECK FOR LEAKS AT POWER STEERING PUMP PRESSURE HOSE ORING. AND CHECK POWER STEERING LINES TO PUMP FOR LEAKS.

YOU HAVE AIR IN THE POWER STEERING SYSTEM.YOU NEED TO BLEED POWER STEERING PUMP FIRST BEFORE DRIVING VECHICLE.CHECK POWER STEERING FLUID LEVEL ADD MORE POWER STEERING UNTIL REACH FULL COLD MARK..RAISE VECHICLE FRONT WHEELS OFF THE GROUND.START ENGINE LET IT IDLE WHILE TURNING STEERING WHEEL LEFT TO RIGHT NON STOP DONT LOCK OR STOP STEERING WHEEL KEEP TURNING IT SEVERAL TIMES CHECK POWER STEERING FLUID IF LOW ADD UNTIL YOU GET COLD MARK ON DIP STICK DONT OVER FILL POWER STEERING PUMP BLOW A SEAL.IF POWER STEERING FLUID LOOK TAN COLOR SYSTEM FULL OF AIR.TURN OFF IGNITION LET CAR SET FOR A WHILE CHECK FLUID LEVEL.IF STEERING WHEEL FEEL STIFF HARD TURNING DONT DRIVE CAR UNTIL YOU HAVE NORMAL STEERING.IF STILL HAVE AIR IN SYSTEM BLEED SYSTEM UNTIL AIR IS OUT.

SIPHON OUT POWER STEERING FLUID.USING A HAND PUMP SIPHON TYPE YOU BUY AT ANY AUTO PARTS STORES.PLACE DRAIN PAN UNDER CAR NEAR POWER STEERING PUMP CATCH FLUID WHEN YOU REMOVE POWER STEERING LINES AT THE PUMP.REMOVE DRIVE BELT.THEN REMOVE POWER STEERING PUMP.YOU NEED TO TAKE OLD PUMP WITH YOU.TAKE NEW PUMP AND OLD PUMP TO MACHINE SHOP THEY WILL REMOVE POWER STEERING PUMP PULLEY FROM THE OLD PUMP TRANSFER PULLEY TO THE NEW POWER STEERING PUMP YOU NEED TO BUY NEW POWER.STEERING HOSES O RINGS TO GO ON NEW POWER STEERING PUMP.HOSES THE OLD ORINGS WILL LEAK. THEN TAKE NEW POWER STEERING PUMP ON INSTALL IN VECHICLE THEN BLEED POWER STEERING SYSTEM.FILL POWER STEERING PUMP UP NEW FLUID.WAIT FEW MINUTES.WHEN LEVEL DROP ADD MORE FLUID UNTIL YOU GET TO FULL COLD MARK.START ENGINE 15 SECONDS SHUT OFF CHECK FOR LEAKS. NOW CHECK POWER STEERING AGAIN ADD TO FULL COLD MARK.NOW RAISE FRONT WHEELS OFF GROUND.START ENGINES TURN STEERING LEFT TO RIGHT WITH OUT STOPPING IT DO SEVERAL TIMES THEN CHECK FLUID.ADD TO THE COLD MARK DONT OVER FILL.IF FLUID LOOKS TAN HAS AIR BUBBLES IN SYSTEM WAIT A WHILE UNTIL FLUID SETTLE CHECK FLUID LEVEL.DONT DRIVE VECHICLE UNTIL STEERING FEELS NORMAL.AND IF YOU HEAR NOISES.LOCATE PROBLEM FIX BEFORE DRIVING VECHICLE.

YOU HAVE A RUPTURE PRESSURE LINE IF YOU HAVE NO POWER STEERING FLUID IN THE POWER STEERING RESERVOIR.LOCATE LEAK THEN BLEED POWER STEERING SYSTEM BY ADDING POWER STEERING TO RESERVOIR.DONT OVER FILL BY FULL COLD MARK ON POWER STEERING DIP STICK.ADD FLUID TO RESERVOIR WAIT A 2 MINUTES.CHECK FLUID LEVEL AGAIN.WHEN POWER STEERING FLUID LEVEL STOP DROPPING.START ENGINE LET IT RUN FOR 10 SECONDS.THEN TURN OFF ENGINE CHECK POWER STEERING FLUID ADD FLUID IF FLUID LEVEL DROPS. WHEN FLUID LEVEL STOP DROPPING.SAFELY RAISE SUPPORT VECHICLE FRONT WHEELS.START ENGINE.NOW TURN STEERING WHEEL GENTLY FROM STOP TO STOP MEANING LEFT TO RIGHT DONT HOLD IN POSITION.LET THE STOP TO STOP BE QUICK.CHECK POWER STEERING FLUID AFTER YOU HAVE TURN STEERING WHEEL ABOUT 7 STOP TO STOP.WHEN FLUID LEVEL STOP DROPPING YOU AT HOT MARK ON DIP STICK BLEEDING PROCESS COMPLETE.TURN OFF ENGINE LOWER VECHICLE BACK TO GROUND WAIT ABOUT 5 MINUTES CHECK YOUR FLUID LEVEL.IF FLUID LOOKS LIKE A TAN COLOR.YOUR POWER STEERING SYSTEM FULL OF AIR.TURN OFF VECHICLE LET VECHICLE SET A LONG WHILE TO AIR BUBBLES SETTLE DOWN LOOK FOR LEAKS AROUND POWER STEERING PUMP FRONT SEAL AND CHECK FOR LEAKS AROUND POWER STEERING LINES.

CHANGING POWER STEERING PUMP YOU HAVE TO PLACE A DRAIN PAN UNDER THE VECHICLE. SIPHON OUT POWER STEERING FLUID WITH A SIPHONER DONT USE YOUR MOUTH TO SIPHON SWALLOWING POWER STEERING FLUID CAN BE FATAL MAKE YOU SICK.WHEN ALL POWER STEERING FLUID IS REMOVED FROM POWER STEERING PUMP.REMOVE DRIVE BELT.THEN REMOVE THE POWER STEERING PUMP.THEN YOU HAVE TO REMOVE THE POWER STEERING PUMP PULLEY THE NEW POWER STEERING PUMP DONT HAVE A PULLEY YOU HAVE TO HAVE REMOVE PULLEY FROM THE OLD POWER STEERING PUMP.YOU NEED A PUMP PULLEY REMOVER AND A PULLEY INSTALLER.YOU CAN TAKE OLD POWER STEERING PUMP AND NEW POWER STEERING PUMP TO A MACHINE SHOP.THEY WILL REMOVE PULLEY OFF OLD PUMP PRESS IT ON NEW POWER STEERING PUMP.THAT WOULD BE CHEAPER THAN BUYING THE PULLER AND INSTALLER.GO TO AUTO PARTS STORE BUY NEW HIGH PRESSURE LINE O RING GOES TO PRESSURE LINE GOING INTO POWER STEERING PUMP.ONCE YOU GET NEW PUMP READY PULLEY BEEN PRESSED ON.TAKE POWER STEERING PUMP HOME PUT IT ON. BLEED POWER STEERING SYSTEM.WHAT YOU DO WHEN YOU GET NEW PUMP INSTALLED HIGH PRESSURE LINE IN PLACE.PUMP BOLTED IN DRIVE BELT ON POUR POWER STEERING FLUID IN POWER STEERING PUMP UNTIL FLUID LEVEL STOP DROPPING AND YOUR LEVEL ON POWER STEERING DIP STICK AT COLD LEVEL.NOW START CAR UP LET IT IDLE FOR 3 MINUTES.THEN TURN OFF ENGINE CHECK POWER STEERING FLUID IF FLUID LEVEL DROP ADD LITTLE MORE UNTIL LEVEL ON DIP STICK ON COLD MARK DONT OVER FILL.NOW SAFELY RAISE SUPPORT FRONT OF VECHICLE. START THE ENGINE.TURN STEERING WHEEL FROM ALL THE WAY FROM LEFT TO RIGHT DONT STOP LOCK WHEEL .GO LEFT TO RIGHT SEVERAL TIMES.THEN TURN OFF ENGINE CHECK FLUID LEVEL.IF ALL IS GOOD LET VECHICLE BACK DOWN LET IT SIT FOR A WHILE CHECK FLUID AGAIN.DONT DRIVE VECHICLE IF POWER STEERING PUMP MAKE NOISES OR YOUR STEERING FEEL STIFF HARD TO TURN.JUST MAKE SURE FLUID LEVEL RIGHT AND DRIVE BELT TIGHT GOOD LUCK.

FIRST OF ALL YOU HAVE TO REMOVE POWER STEERING FLUID.USING A SUCTION GUN OR LARGE SYRINGE.REMOVE MUCH FLUID AS POSSIBLE.WHEN DONE REMOVING POWER STEERING FLUID.YOU NEED A INLINE WRENCH AND OPEN BOX END WRENCH TO REMOVE THE POWER STEERING HOSE.YOU HAVE TO REMOVE POWER STEERING LINE FROM THE RACK.UNDER THE CAR SAFELY RAISE AND SUPPORT VECHICLE. THEN REMOVE THE TIRE OR WHEEL.THEN REMOVE THE INNER FENDER SPLASH SHIELD.ITS GOING TO BE A TIGHT FIT AND HARD PLACE TO GET YOUR HAND TO REMOVE THE POWER STEERING LINE FROM BOTTOM.WHEN DONE.MAKE SURE NEW POWER STEERING HOSE OR LINE HAS NEW O RINGS.WHEN INSTALLING THE THE NEW STEERING HOSE.WHEN ALL IS DONE BLEED POWER STEERING SYSTEM. FILL UP POWER STEERING PUMP TO CORRECT FLUID LEVEL.THEN LET IT SET FOR 2 MINUTES UNDISTURBED.THEN START THE ENGINE RUN IT FOR 2 TO 3 SECONDS.ONLY CHECK THE RESERVOIR AND ADD MORE FLUID AS NECESSARY.REPEAT THE OPERATION UNTIL THE FLUID LEVEL REMAIN CONSTANT.NOW RAISE FRONT OF THE CAR UNTIL THE WHEELS CLEAR THE GROUND START THE ENGINE AND INCREASE THE SPEED TO ABOUT 1500 RPM.NOW TURN THE STEERING WHEEL GENTLY FROM STOP TO STOP CHECK THE FLUID LEVEL.LOWER THE VECHICLE TO THE GROUND WITH ENGINE STILL RUNNING MOVE THE CAR FORWARD SUFFICIENTY TO OBTAIN FULL RIGHT LOCK FOLLOWED BY FULL LEFT LOCK BUT DONT HOLD THE SREERING WHEEL FIRMLY AGAINST THE STOPS.RECHECK THE FLUID LEVEL IF THE FLUID IN THE RESERVOIR IS EXTREMELY FOAMY ALLOW THE CAR TO STAND FOR A FEW MINUTES.WITH ENGINE OFF.WHEN JOB IS FINISH. WARNING DONT DRIVE CAR ON ROAD IF YOUR FLUID STILL FOAMY OR POWER STEERING PUMP MAKE NOISES.REBLEED THE SYSTEM AND CHECK FLUID LEVEL AND CHECK FOR LEAKS.DONT DRIVE CAR UNTIL YOU START FEELING NORMAL STEERING.IF YOU HAVE TROUBLE DONT DRIVE.HAVE IT TOWED TO THE NEAREST GARAGE.

i pERSONALY WOULD REPLACE IT MYSELF EVEN WITHOUT MY 30yrs Of Experience in this Field. I have Enclosed Instructions for you to use. PLEASE dont Forget to RATE me As MOST folks DONT remember to that is how WE Get our Ratings such as GURU THANK YOU and Good Luck On The Job, Dont PAY a dime If YOU CAN > D I Y

REMOVAL PROCEDURE

1. Remove the power steering pressure hose (2) from the power steering pump (1).
2. Raise the vehicle on a hoist. Refer to Vehicle Lifting.
3. Remove the front exhaust pipe, automatic transmission only. Refer to Intermediate Pipe Replacement in Exhaust System
4. Remove the power steering pressure hose (1) from the power steering gear (3).
5. Remove the power steering hose retainer (2).
6. Remove the power steering pressure hose (1) from the vehicle
   1. Install the power steering pressure hose (1) to the vehicle
   2. Install the power steering hose retainers (2). NOTICE: Refer to Fastener Notice in Service Precautions.
   3. Install the power steering pressure hose (1) to the power steering gear (3). Tighten the fitting to 27 Nm (20 ft. lbs.).
   4. Install the front exhaust pipe, if removed. Refer to Intermediate Pipe Replacement in Exhaust System.
   5. Lower the vehicle.
      1. Install the power steering pressure hose (2) to the power steering pump (1). Tighten the fitting to 27 Nm (20 ft. lbs.).
      2. Bleed the power steering system. Refer to Bleeding Power Steering System in Service and Repair of Steering.