Question about 1987 Ford Crown Victoria

1 Answer

How do i put a fuel pump on a crown victoria 1987 5.0

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 6,784 Answers

Hi, this will help you achieve your goal.


Step 1

Park the vehicle in a safe place and make sure there is enough room around the back of the vehicle for you to work and move tools around.

Step 2

Start the engine and let it idle while you relieve the fuel system pressure by removing the fuel pump fuse or relay from the fuse box. Wait a few seconds for the engine to stall, turn the ignition key off and replace the relay or fuse.

Step 3

Raise the back of your car using a floor jack and support it safely on jack stands.

Step 4

Disconnect the fuel tank filler pipe and the fuel pump connector located above the cross member underneath the vehicle.

Step 5

Disconnect the vapor tube from the tee connector on the right side of the car-passenger side-and the vapor line from the canister tube.

Step 6

Support the fuel tank with a jack and remove the nuts from the holding strap using a wrench or ratchet and socket. Move the strap away and lower the fuel tank. Discard the fuel tank mounting studs.

Step 7

Unplug the pressure transducer electrical connector located on the top rear corner of the fuel tank.

Step 8

Clean the area around the fuel pump mounting flange and remove the flange mounting bolts in a crisscross pattern.

Step 9

Lift the fuel pump assembly off the tank. Replace the new fuel pump in the assembly and install the assembly in the tank. Install the flange screws and torque to 89 inch lbs. (10Nm) using a crisscross pattern.

Step 10

Raise the fuel tank to its mounting position, install the strap using new mounting studs and torque the nuts to 26 foot lbs. (35 Nm).

Step 11

Connect the fuel pressure transducer electrical connector, vapor tube to the tee connector, vapor line to the canister tube, fuel tank filler pipe and fuel pump electrical connector.

Step 12

Lower the vehicle, start the engine and check for leaks.

Posted on Jun 26, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 261 Answers

SOURCE: 2000 Ford Crown Victoria

when you hold the accelerator does the vehicle stay running? if so the problem is in ithe IAC idle air control motor, take a small screw driver and using the handle tap the iac motor and usualy the motor will kick in and the vehicle will run fine then if the problem is rectified replace the IAC

Posted on Nov 24, 2008

ltfrc
  • 227 Answers

SOURCE: 1987 Ford Crown Victoria LTD

If it was an old police vehicle it has probably got an ignition kill switch located somewhere. This will have to be removed. And the wiring put back to factory standards. If not an old police car you are not getting voltage to the starter which is a bad relay. Do you get a clicking sound when you try to start? If yes, have someone keep hitting the start and listen and look for a relay under the hood.

Posted on Jan 19, 2009

  • 508 Answers

SOURCE: 94 CROWN VICTORIA FUEL PUMP

Yes you can replace it. It is in the fuel tank. You will need to drain the tank and remove it to gain access to the fuel pump. A floor jack will help when lowering the fuel tank. If you fo to a dealer to do this you will be looking probably around $700.00 to replace the pump.

Posted on Feb 18, 2009

BPALepine
  • 61 Answers

SOURCE: how do u install a 2002 crown victoria fuel pump

According to Ford the fuel pumps are located in the fuel tank. If you need help with this procedure let me know.

Posted on Apr 23, 2009

jrock1094
  • 158 Answers

SOURCE: How to change a fuel pump on 1998 ford crown

you have to remove the fuel tank- it is located inside the tank

Posted on Feb 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the fuel pump relay located on a 87 crown victoria


It's located in the trunk on the drivers side behind the trunk carpet.

Aug 17, 2010 | 1987 Ford Crown Victoria

1 Answer

I have a 1997 crown victoria it just turn over but want start. fuel pump


does it kinda start or just turns over? check for fuel pressure. do this by putting key in on position and then checking to see if any gas will come out of the shradder valve (located on the fuel rail). if there is no gas coming out. fuel pump is dead. check to see if you are getting power to the fuel pump before ou rip it out...might be a busted wire going to the fuel pump

May 29, 2010 | 1997 Ford Crown Victoria

1 Answer

How do I find the fuse for 1987 crown victoria fuel pump?


under driver side of dash.there may possibly be one under hood in fuse panel.why are looking for the fuel pump fuse???also there should be a fuel pump kill switch on passenger side floor kick pannel to the right of passengers foot behind plastic or in trunk..hope this done you some good....

Jul 05, 2009 | 1987 Ford Crown Victoria

2 Answers

NO POWER TO FUEL PUMP


relay has power to it from the battery?

May 25, 2009 | 1987 Ford Crown Victoria

1 Answer

94 CROWN VICTORIA FUEL PUMP


Yes you can replace it. It is in the fuel tank. You will need to drain the tank and remove it to gain access to the fuel pump. A floor jack will help when lowering the fuel tank. If you fo to a dealer to do this you will be looking probably around $700.00 to replace the pump.

Feb 17, 2009 | 1994 Ford Crown Victoria

1 Answer

No fuel


Check the inertia fuel switch located near the floorboard. It will have a button that you can press to reset the switch.

Jan 30, 2009 | 1988 Ford Crown Victoria

1 Answer

1987 Ford Crown Victoria LTD


If it was an old police vehicle it has probably got an ignition kill switch located somewhere. This will have to be removed. And the wiring put back to factory standards. If not an old police car you are not getting voltage to the starter which is a bad relay. Do you get a clicking sound when you try to start? If yes, have someone keep hitting the start and listen and look for a relay under the hood.

Sep 26, 2008 | 1987 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

439 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...