Question about 1999 Chevrolet Blazer

1 Answer

How do i incert and seal my fuel pump into the tank of my 1999 chevy 4x4 pick up I want to make sure i have it sealed correctly

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 6,982 Answers

There is a rubber ring that goes under the plate. Once installed, it's all you need.

Posted on Jun 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 chevy lumina installed new fuel pump .pump not getting fire


check the locking ring and your seal on your fuel tank may be sucking air.

Dec 21, 2013 | Cars & Trucks

3 Answers

Where is my fuel pump located in a 1994 cheyenne chevy pick up 4x4 5.7 v8


Hello
The fuel pump is elelctic and it is located inside the fuel tank, the fuel tank must be removed to service the fuel pump.

Nov 11, 2010 | 1994 Chevrolet C2500

1 Answer

Instructions on how to remove fuel pump for 95 chevy blazer 4x4


Removal & Installation
To Remove:


  1. Properly relieve the fuel system pressure.
  2. Drain the fuel tank through the filler pipe.
  3. Support the fuel tank.
  4. Remove or disconnect the following:

    • Negative battery cable
    • Filler neck
    • Shield and tank straps
    • Fuel lines and vapor hose from pump and tank
    • Electrical connection from fuel pump
    • Fuel tank
    • Fuel pump/sending unit assembly by turning the locking ring (located on top
      of the fuel tank) counterclockwise using a spanner wrench
    • Fuel pump from the fuel lever sending device

To Install:


  1. Install or connect the following:

    • Fuel pump in tank with new seal around opening
    • Tank and connect fuel lines and vapor hose
    • Tank to the frame

      1. Torque to: 33 ft. lbs. (45 Nm)

    • Shield
    • Fuel filler neck and clamp
    • Negative battery cable

  2. Refill the tank.
  3. Run the engine and check for leaks.






View of the in-tank fuel pump assembly.
7924jg21.gif




prev.gif next.gif

Sep 23, 2010 | Chevrolet Blazer Cars & Trucks

1 Answer

NEED TO REPLACE FUEL PUMP FOR 1996 fORD eXPLORER, V6 4.0. WHERE IS IT AND HOW DO I GET TO IT?


Great SUV, I have the same model; for Ford Ranger/Explorer/Mountaineer 1991-1999 check this procedure to Fuel Pump - REMOVAL & INSTALLATION...
(see Figures 1, 2 and 3)

To gain access to the fuel pump, it is necessary to remove the fuel tank.
  1. Depressurize the fuel system and remove the fuel tank from the vehicle.
  2. Remove any dirt that has accumulated around the fuel pump attaching flange, to prevent it from entering the tank during service.
  3. Turn the fuel pump locking ring counterclockwise using a locking ring removal tool and remove the locking ring.
  4. Remove the fuel pump and bracket assembly.
  5. Remove the seal gasket and discard it.
To install:
  1. Put a light coating of heavy grease on a new seal ring to hold it in place during assembly. Install it in fuel tank ring groove.
ab80e6f.jpg

Fig. 1: Fuel pump and sending unit used on the Regular Cab Ranger pick-up

fe10412.jpg

Fig. 2: Fuel pump and sending unit used on the Super Cab Ranger pick-up

2bf46c6.jpg

Fig. 3: Fuel pump and sending unit used on the Explorer and Mountaineer
  1. Insert the fuel pump assembly into the fuel tank, then secure it in place with the locking ring. Tighten the ring until secure.
  2. Install the tank in the vehicle.
  3. Install a minimum of 10 gallons of fuel and check for leaks.
  4. Install a pressure gauge on the throttle body valve and turn the ignition ON for 3 seconds. Turn the key OFF , then repeat the key cycle five to ten times until the pressure gauge shows at least 30 psi. Reinspect for leaks at the fittings.
  5. Remove the pressure gauge. Start the engine and check for fuel leaks.

Hope help with this; remember comment and rated this help. TY for using Fixya.

May 28, 2010 | 1996 Ford Explorer

1 Answer

Cruise doesn't work on 1999 Chevy Suburban 6.5 Diesel 4x4


sounds like speed sensor that where it picks up the pulse for cruise

Nov 24, 2009 | 1999 Chevrolet Suburban

1 Answer

1999 Chevy Blazer 4x4 4door 4.3L V6 Fuel pump replacement.


Hello,
Replacing the sending unit / module is optional when its a metal top module. If it's plastic I would replace the whole thing reguardless.

I hope this helps.

Roy

Nov 05, 2009 | Chevrolet Blazer Cars & Trucks

2 Answers

I need to remove the fuel pump from my 99 chevy blazer , is there an access panel or does the fuel tank have to dropped?


  1. Properly relieve the fuel system pressure.
  2. Drain the fuel tank.
  3. Support the fuel tank.
    1. Remove or disconnect the following:
    2. Negative battery cable
    • Filler neck from the tank
    • Shield from tank and tank straps
    • Fuel lines and vapor hose from pump
    • Electrical connection from fuel pump
    • Fuel tank
    • Fuel pump/sending unit assembly by turning the locking ring (located on top of the fuel tank) counterclockwise using a spanner wrench
    • Fuel pump from the fuel lever sending device
  • To install:
    Install or connect the following:
    • Fuel pump in tank with new seal around opening

    NOTE The fuel pump strainer must be in a horizontal position when the fuel sender is installed in the tank. When installing the sender assembly, make sure that the fuel pump strainer does not block full travel of the float arm.


    • Tank and connect fuel lines and vapor hose
    • Tank to the frame. Torque the fasteners to 33 ft. lbs. (45 Nm).
    • Shield
    • Fuel filler neck and clamp
    • Negative battery cable
    1. Refill the tank.
    2. Run the engine and check for leaks.
    6207c87.gif
    View of the in-tank fuel pump assembly

    Oct 13, 2009 | 1999 Chevrolet Blazer

    1 Answer

    HOW DO I REPLACE THE FUEL PUMP ON 2003 CHEVY S10 PICK UP


    Removal & Installation To Remove:
    1. Properly relieve the fuel system pressure.
    2. Drain the fuel tank through the filler pipe.
    3. Support the fuel tank.
    4. Remove or disconnect the following:
      • Negative battery cable
      • Filler neck
      • Shield and tank straps
      • Fuel lines and vapor hose from pump and tank
      • Electrical connection from fuel pump
      • Fuel tank
      • Fuel pump/sending unit assembly by turning the locking ring (located on top of the fuel tank) counterclockwise using a spanner wrench
      • Fuel pump from the fuel lever sending device
    To Install:
    1. Install or connect the following:
      • Fuel pump in tank with new seal around opening
      • Tank and connect fuel lines and vapor hose
      • Tank to the frame
        1. Torque to: 33 ft. lbs. (45 Nm)
      • Shield
      • Fuel filler neck and clamp
      • Negative battery cable
    2. Refill the tank.
    3. Run the engine and check for leaks.
    1e2538e.gif

    Jun 26, 2009 | 1998 Chevrolet S-10 Pickup

    1 Answer

    Fuel Pump Bad.


    remove fuel tank from vehicle and remove lock ring from tank swap fuel pump out..make sure sealing ring is installed properly

    May 09, 2009 | 1992 Chevrolet Lumina

    3 Answers

    1998 Chevy tahoe Hard to start when cold


    replace your MAP sensor(manifold absolute pressure) the map sensor is the computer for your fuel pressure regulator telling how much pressure. Unless your tahoe runs like **** going up hill than it inevitably your fuel pump

    Feb 17, 2009 | 1999 Chevrolet C/K 2500

    Not finding what you are looking for?
    1999 Chevrolet Blazer Logo

    Related Topics:

    57 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8152 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...