Question about 1996 GMC Sierra

3 Answers

How to replace my turn signal switch - 1996 GMC Sierra

Posted by on

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 2,984 Answers

Multi-function Switch Removal & Installation To Remove:
To Remove:

  1. Remove the steering column trim covers.
  2. Remove the wire harness from the retainers as needed.
  3. Slide the turn signal and multifunction switch connectors out from the bulk head connector.
  4. Remove the two mounting screws and remove the multi-function switch from the steering column.

To Install:
  1. Install the multi-function switch on the steering column.
    • Tighten the screws to 42 lb in (4.7 Nm).
  2. Slide the turn signal and multifunction switch connectors into the bulkhead connector.
  3. Install the harness in the original retainers.
  4. Install the steering column trim covers.
how to replace my turn signal switch - 7f81df3.gif

Posted on Jun 25, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 578 Answers

Take off the steering colume cover and and unplug the wiring an if there are screw remove them and pull it off then replace the new one

Posted on Jun 25, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You can slide the turn signal switch and can be taken apart to be cleaned & lubed. dude when the spring pushes the lever back to the center and turns the signal off unless you hold it so try checking if it is still working. put the switch back at the front.



===princecasanova====

Posted on Aug 25, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The hazard back lights wont quit blinking when car is running even when i pull the fuse on a 2002 buick regal


What fuse are you pulling ?

Hazard Lamps
The hazard warning switch is part of the turn signal switch. The turn signal switch receives battery voltage at all times through the HAZARD SWITCH Fuse. When the hazard switch is placed in the HAZARD position, battery voltage is applied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher sends a turn signal flasher signal to the turn signal switch. The turn signal switch provides all of the turn lamps and turn indicators with the turn signal flasher signal, simultaneously flashing them on and off.

Turn Signal Lamps
The front turn signal lamps are made up of the front park/turn signal lamps and rear turn signal lamps. The front turn signal lamps flash with the rear turn signal lamps when a turn is initiated using the turn signal/multifunction lever. The turn signals will operate only with the ignition switch in the RUN position and will not operate during hazard flasher operation.
When the ignition is turned to the RUN position, battery voltage is supplied to the TURN SIGNAL Fuse. Battery voltage is then applied through the turn signal fuse circuit to the turn signal switch. When the turn signal switch is placed in the LH or RH position, voltage is supplied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher supplies a turn signal flasher signal to the turn signal switch. With the turn signal switch in the LH or RH position the corresponding turn signal indicator, rear turn signal, and front turn signal receive the turn signal switch signal and will flash. The front turn signals receive the turn signal switch signal from the turn signal switch via the BCM. The turn lamps are permanently grounded.

Replace the turn signal switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column - Tilt.

Feb 11, 2017 | Buick Cars & Trucks

1 Answer

How do I replace the turn signal assembly on a 97 Chrysler LHS?


Carmon, check the posted links to see how to replace the turn signal switch. "I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

How to Install Replace Turn Signal Wiper Switch Dodge Intrepid 93 97...
How to Replace Turn Signal Switch Chrysler Sebring
97 dodge intrepid turn signal problems

May 31, 2016 | Chrysler Cars & Trucks

1 Answer

Why my turn signal doesn't automatically shut down anymore?


Your turn signal switch is most probably faulty. You will need to replace it. Please, check the videos below. The first video shows a similar problem on a Renault Clio. The second one shows the operations to replace the turn signal switch. I think that the operations are quite similar in most modern cars. Good luck!

Turn Signal Switch Problem - Solved
(copy and paste the link into your browser)

http://www.youtube.com/watch?v=s0MQvwzXFIk


How to Easily Replace a Turn Signal Switch - Clio 2 and other Renault/Dacia
(copy and paste the link into your browser)

http://www.youtube.com/watch?v=JKiy-F8pd6o

Turn Signal Switch Problem Solved
How to Easily Replace Turn Signal Switch Clio 2 and other Renault Dacia

Feb 18, 2016 | Cars & Trucks

1 Answer

Passenger side turn signal flashes faster but dont work even at day runing light, comes on when head lights are on, replace bulb and socket because was melted but stilldoes the same


Turn Signal Lamps
The turn signal lamps may only be activated with the ignition switch in RUN or BULB TEST position. The T/SIG fuse supplies ignition voltage to the turn signal switch. When the turn signal switch is placed in either the left or right position, the turn signal switch sends an ignition voltage to the hazard lamp/turn signal flasher, which sends an on-off signal to the turn signal switch. When the turn signal switch receives the on-off signal it will send that signal to the following lamps on the LH or RH side:
?€¢
The Rear Turn Lamp


?€¢
The Turn Signal Indicator


?€¢
The Sidemarker Lamp


?€¢
The Sideview Mirror (Pontiac Thunder only)

The turn signal switch also sends a separate on-off signal to the Daytime Running Lamps (DRL) control module, which relays the signal to the appropriate front turn signal. The front turn signals are grounded at G101 and G102. The rear turn signals are grounded at G401. The sidemarker lamps are grounded through the corresponding front parklamp.
The sideview mirror turn signals are a bank of LEDs placed behind the mirror glass.
The hazard lamps operate on battery voltage. The HAZARD fuse supplies battery voltage to the turn signal switch. When the hazard switch is pressed, the turn signal switch sends battery voltage to the hazard lamp/turn signal flasher, which sends an on-off signal to the turn signal switch. The turn signal switch send the on-off signal to all the turn signal lamps, causing all the lamps to flash including both IPC turn signal indicators. The hazard lamp/turn signal flasher is grounded at G200.
When the parklamps are ON, the sidemarker lamps receive voltage from the park lamp supply voltage circuit and illuminate. The sidemarker lamp is grounded through the corresponding rear turn signal. When the turn signal switch is place in the left or right hand position, the rear turn signal illuminates and the sidemarker lamp will loose its ground, causing the sidemarker lamp to turn off when the turn signals are on and to illuminate again when the turn signal is off.
Which blub an socket did you replace ? check the other blub ? The switch and or the flasher module can cause this problem .
Replace the turn signal switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column.
Did you complete the replacement?

Which

Oct 11, 2015 | 2001 Pontiac Montana

2 Answers

Grand scenic indicators not self cancelling


Your turn signal switch is most probably faulty. You will need to replace it. Please, check the videos below. The first video shows a similar problem on a Renault Clio. The second one shows the operations to replace the turn signal switch. I think that the operations are quite similar in most modern cars. Good luck!

Turn Signal Switch Problem - Solved

http://www.youtube.com/watch?v=s0MQvwzXFIk

How to Easily Replace a Turn Signal Switch - Clio 2 and other Renault/Dacia


http://www.youtube.com/watch?v=JKiy-F8pd6o


Turn Signal Switch Problem Solved How to Easily Replace Turn Signal Switch Clio 2 and other Renault Dacia

Jun 12, 2012 | Renault Grand Cars & Trucks

2 Answers

I have a 1995 grand prix Blinkers dont work but, other lights do.


First check turn signal fuse and relay if, they are good then try pressing on and off the hazard switch while turning the signal switch on.If signals start to work replace hazard switch.If hazard switch is good then replace turn signal switch.

May 02, 2011 | 1995 Pontiac Grand Prix

2 Answers

Turn signal clicker comes on randomly but doesn't affect lights


No the dash is the hazard light switch, it's also the turn signal flasher, dealer part only replace, replacing it will fix your problem. Feel the switch when you hear the clicking.

May 21, 2010 | 2004 Chevrolet Malibu

2 Answers

Left signal wont turn off, and right signal wont


I Think your turn signal switch is most probably faulty. So that, you will need to replace it. Please, check the video below. It shows the operations to replace the turn signal switch. I think that the operations are quite similar in most modern cars. Good luck!

How to Easily Replace a Turn Signal Switch - Clio 2 and other Renault/Dacia

http://www.youtube.com/watch?v=JKiy-F8pd6o
How to Easily Replace Turn Signal Switch Clio 2 and other Renault Dacia

Mar 27, 2010 | 2004 Saab 9-3

2 Answers

04 impala turn signals stop and starti ntermitently


The turn signal flasher is built in to the hazard switch. They are common for going bad. If the turn signals quit again, try pushing the hazard switch on and off a bunch of times really quick. If the turn signals start working again, replace the hazard switch

Aug 31, 2009 | 2004 Chevrolet Impala

3 Answers

Turn signals


replaced turn signal flashers and muti switch turn signal still won't work Why?

Nov 08, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
1996 GMC Sierra Logo

2,024 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...