Question about 1989 GMC Sierra

1 Answer

How do you change the cab mounts? - 1989 GMC Sierra

Posted by on

  • cy schousboe May 11, 2010

    Front or rear?

  • yadayada
    yadayada May 11, 2010

    why would u want to?



1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 21 Answers

Do one side at a time, unbolt one side, loosen the other. use a floor jack with wood or whatever is needed to safely jack the cab up off the frame and remove the bushings

Posted on Jun 30, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to tighten cab mounts

Bolts located on underside of the truck. I believe that 6 bolts hold the cab on to the frame if its a crew cab. Four bolts can be seen from laying under the truck. You can see the rubber mounts that attach it the the cab from the frame. The other 2 in the back are on the floor board by rear seat or back panel. they connect to the frame also. Make sure the cab is aligned with the bed. It can be shifted. Make sure the bolts are straight and not leaning forward or backwards. Inspect the rubber cab mounts to make sure they are good. You will understand when you start investigating the mounting area.

Sep 11, 2016 | 2005 Ford F 350 Super Duty

1 Answer

Is the wheel base the same on a 2007 extended cab colorado the same as the four door model.

The part numbers for the frames are different, which could be just where different bolts mount. the parking brake cables for extended cab and 4 door are the same which leads me to believe that the wheel bases are the same. Your best bet would be to contact a salvage yard in your area and check with them.

Jan 08, 2016 | 2007 Chevrolet Chevrolet Colorado LT

1 Answer

2000 GMC Sonoma 4x4 Has a constant loud Chirp that happens every few seconds whether idling or driving. I can not seem to locate where it is coming from but sounds like right under me in the drivers seat....

try this.. with the vehicle the drivers door with the window down..sit in the seat and bounce up and down in the seat..listen for your squeak/chirp..I am thinking its either the seat mounts or the body mounts under the can spray wd 40 on the rubber cab mount bushings if you dont hear the sqeak when you bounce on the seat.. get out and grab the door by the far end of the window frame and shake the cab upand down.. you can use petroleum jelly on the seat rails under the seat for a lubricant..dont use regular grease because if you do..and get in with nice clothes on(and catch the bottom of your jacket under the side of the seat)..eeewww...if there is no sqeak, try starting..if you hear it now..its either mounts or a loose belt..

Dec 22, 2013 | 2000 GMC Sonoma Extended Cab

1 Answer

How to change cab mount bushings

Remove Cab bolts and lift body with lift. If lift is not accessible then remove mount bolts on one side and jack with block of wood to reduce body damage possiblity (Use body line). Jack body just high enough to remove bushing. Use caution watch hands and avoid pinch points whenever possible.

Jan 10, 2013 | Ford F-250 Cars & Trucks

1 Answer

Replace cab mounts

the hardest part is getting the old cab mount bolts out i recomend spraying them down good with pb blaster you dont want to break the bolts not a hard job if the bolts come out easy.

Sep 09, 2012 | Cars & Trucks

1 Answer

I have a 1997 gmc sierra pickup and the cab mounts are rusting out very badly. The rest of the truck looks great but those cab mounts have become a real eye sore an making the truck look run down. My...

Those cab mounts can be purchased at a local GM dealer. I do believe, then I would suggest having it in a preffered body shop and they can be replaced. Another alternative is finding a used frame in good shape and swapping out frames. Steve

Feb 08, 2011 | 1997 GMC Sierra

2 Answers

2004 Dodge Dakota Quad Cab: The brake lights wont light up at the rear of the truck and the Center High Mounted Stop Light wont turn off.

Im having the same issue on my 04 Quad Cab Dakota. Changed out the brake light switch but still no brake lights. You have any luck ?

Oct 09, 2010 | 2000 Chrysler Concorde

1 Answer

How to change cab mounts

use a block of wood and a floor jack to lift cab off mounts after unbolting them. Then simply install new ones lower cab back down and tighten the bolts. Easy job

Mar 05, 2010 | 1989 Chevrolet S-10 Blazer

1 Answer

Cab mount brackets are rusted looking to replace them

grind out the mounts on the body until you hit actual metal and weld some steel on it and make new mounts

May 15, 2009 | 1987 Ford Ranger

2 Answers

Rotton body mounts

Are you taking about the rubber mount bushings? You can get replacements at your local Dodge dealer, or you could opt for a 2" body lift which comes with new mounts.

Mar 07, 2009 | 1996 Dodge Ram 3500 Club Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

80531 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides