Question about 2000 Chrysler Concorde

2 Answers

2000 Concorde - power locks, interior lights, radio not working

The alarm chirps when key is turned on, also the trunk release and remote no longer work.

Posted by on

  • mikepoulin65 Jun 26, 2009

    the fuse for the interior lights was blown...all is good now!!!

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

It sounds like your interior lamp fuse is blown. If you know where to look for your fuses check #19 fuse. Its a ten amp fuse. My interior lamp fuse keeps blowing so my remote, trunk open button, power mirrors, and door locks no longer work.I got my radio working cause I ran a wire from the fuse panel directly to the radio. I hope this helped. Its hard finding the right answers sometimes.

Posted on Oct 25, 2014

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

There is most likely a fault in the system and it will have to be reapired by certified tech

Posted on Jun 25, 2009

  • Nate Stansfield
    Nate Stansfield Jun 26, 2009

    That was my next suggestion. It should always be the first thing checked. Good Job

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is the alarm system, automatic door lock and radio not working?


have you checked the fuses under hood as well as in the interior under dash, if all ok the key fob may need new batteries

May 05, 2014 | 2002 Lexus ES 300

5 Answers

Security light flashes and it won't start


top
CODE ALARM SYSTEM
information is always subject to change and correction Used on:
Impreza 1996-2001
Legacy 1995-1999
Forester 1998-2000
codealarmremote2.jpgBattery GP-23A
Lock: Left button will lock all doors. Double chirp indicates locked.
Unlock: Right button will unlock driver's door only. Hold unlock button app 6 seconds, it will unlock all doors including rear gate. Single chirp indicated unlock.
If the car chirps or lights flash 4x the alarm was triggered.
Panic. Press both buttons to activate emergency honk and flashing lights.
Valet mode: With optional alarm only Press the red alarm button on the left of the steering wheel. The light will quickly double flash. To re-set back to normal mode, press the red alarm light button again

Battery failed and lights flashing?
Parking lights will flash when the vehicle's battery is disconnected and reconnected.
To stop lights from flashing, either:
Press remote transmitter “UNLOCK” button once OR turn the ignition switch to the “ON” position and press programming button for one second (see below).
The vehicle interior (courtesy) light and door open warning light (DOOR AJAR indicator) will then illuminate for 60 seconds when the ignition is turned off, or until the doors are locked with the remote transmitter. Yes, the dashboard instrument panel lights will flash when the parking lights flash.
Programming or Overriding the Alarm when you have lost the remote
Open driver's door.
Turn ignition key to 'On'
Press and *hold programming button* in (see diagram, button under dashboard)
After 15 seconds the the door locks will cycle 3 times. Do not release Programming button
Press lock (left) button the remotes to be programmed. The door locks will cycle one time.
Exit programming mode by releasing Programming button under dashboard and turning key to off.

codealarmremote1.jpgCode Alarm Programming Button is under dashboard on the kick panel by the driver's left knee, left of the steering column. If you can't find it, it might still be tucked up in the wiring harness higher up in that same general area. The botton is recessed in a plastic ring (see diagram).
This button must be pressed while programming remotes or if the battery was disconnected and the lights are flashing.
top

Jul 10, 2008 | 1996 Subaru Legacy

1 Answer

My fuel cover does not lock with central locking


According to WIS, the remote boot release is directly connected to the PSE via CAN
The pneumatic system equipment makes vacuum or pressure available for the following systems:Central locking (CL), (pressure, vacuum)Remote trunk release (RTR), (pressure)- actuation via remote trunk release switch or via radio
AD80.20-P-2002-02B Remote trunk release, general notes on Models 202.01/02/12/12 as of 1.6.97,diagnosis, advanced information, RTR 208, 210 as of 1.3.97, 210.081Actuation of PSE control module:The remote trunk release switch (N72s15) is connected to the PSE control module (combined) (A37) via CAN data buses. The remote trunk release radio signal from the key is conveyed to the overhead control panel control module (N70) via theantenna. This transmits the signal to the electronic ignition switch control module (N73) via CAN data buses. If a valid signal is recognized there the PSE control module (combined) (A37) is actuated via CAN data buses. The remote trunk release IR signal from the key is conveyed to the respective door control module (N69/1, N69/2) via the IR receivers (A26/1, A26/2). This transmits the signal to the electronic ignition switch control module (N73) via CAN data buses. If a valid signal is recognized there the PSE control module (combined) (A37) is actuated via CAN data buses.
If the trunk lid is unlocked the LED in the remote trunk releaseswitch (N72s15) is actuated by the PSE control module (combined)(A37) via CAN data buses.
Special features on model 208.4 (Cabriolet)The trunk lid cannot be released remotely with the transmitter key.The rollover bar (RB)/soft top operation control module (N52)signals via the CAN interior data bus whether the soft top is lockedor unlocked or the power soft top switch (S84) is operated. As long as the CAN message reads:"Power soft top switch (S84) operated" or"soft top unlocked"the trunk lid cannot be released remotely.

Pneumatics testingPermissible leakage in complete system at:vacuum of 300 mbar within 1 minute: 30 mbarPermissible leakage of actuators with lines at:vacuum of 300 mbar within 1 minute: 25 mbar
Thanks

Apr 02, 2012 | 2000 Mercedes-Benz CLK

1 Answer

I bought a 1996 Subaru Impreza L 4dr 5speed AWD that runs and starts fine but when I was installing fog lights i noticed that there appears to be an alarm hooked up (it says "code alarm elite DM...


Battery Constant 12v+ Positive Wire (+): Black/Yellow
Battery Constant 12v+ Positive Wire Location: Ignition Switch Harness

Starter Positive Wire (+): Blue/Red
Starter Positive Wire Location: Ignition Switch Harness

Ignition Positive Wire (+): Red
Ignition Positive Wire Location: Ignition Switch Harness

Accessory Positive Wire (+): Red/Yellow
Accessory Positive Wire Location: Ignition Switch Harness

Parking Light Positive Wire (+): Red
Parking Light Positive Wire Location: Low In Drivers Kick Panel

Power Door Lock Negative Wire (-): Add Actuator. This vehicle uses a central door locking system. When connecting a keyless entry, you will need to add a door lock actuator and some units will also require (2) extra relays.
Power Door Lock Negative Wire Location: To Drivers Door Only

Power Door Unlock Negative Wire (-): Add Actuator. This vehicle uses a central door locking system. When connecting a keyless entry, you will need to add a door lock actuator and some units will also require (2) extra relays.
Power Door Unlock Negative Wire Location: To Drivers Door Only

Door Trigger Negative Wire (-): Red/White
Door Trigger Negative Wire Location: In Black Plug, Above Hood Release

Domelight Supervision Wire: Use Door Trigger, Requires Relay
Domelight Supervision Wire Location: N/A

Horn Negative Wire (-): Red/Green
Horn Negative Wire Location: At Steering Column Harness

Tachometer Wire Negative Wire (-): Black/Blue
Tachometer Wire Negative Wire Location: At ECM, Under Drivers Side Dash

Brake Light Positive Wire (+): White/Black
Brake Light Positive Wire Location: At Switch Above Brake Pedal

CODE ALARM SYSTEM

Used on:
Impreza 1996-2001
Legacy 1995-1999
Forester 1998-2000

codealarmremote2.jpgBattery GP-23A

Lock: Left button will lock all doors. Double chirp indicates locked.
Unlock: Right button will unlock driver's door only. Hold unlock button app 6 seconds, it will unlock all doors including rear gate. Single chirp indicated unlock.
If the car chirps or lights flash 4x the alarm was triggered.
Panic. Press both buttons to activate emergency honk and flashing lights.
Valet mode: With optional alarm onlyPress the red alarm button on the left of the steering wheel. The light will quickly double flash. To re-set back to normal mode, press the red alarm light button again

Battery failed and lights flashing?
Parking lights will flash when the vehicle's battery is disconnected and reconnected.
To stop lights from flashing, either:
Press remote transmitter "UNLOCK" button once OR turn the ignition switch to the "ON" position and press programming button for one second (see below).
The vehicle interior (courtesy) light and door open warning light (DOOR AJAR indicator) will then illuminate for 60 seconds when the ignition is turned off, or until the doors are locked with the remote transmitter. Yes, the dashboard instrument panel lights will flash when the parking lights flash.

Programming or Overriding the Alarm when you have lost the remote
Open driver's door.
Turn ignition key to 'On'
Press and *hold programming button* in (see diagram, button under dashboard)
After 15 seconds the the door locks will cycle 3 times. Do not release Programming button.
Press lock (left) button the remotes to be programmed. The door locks will cycle one time. Exit programming mode by releasing Programming button under dashboard and turning key to off.


codealarmremote1.jpgCode Alarm Programming Button is under dashboard on the kick panel by the driver's left knee, left of the steering column. If you can't find it, it might still be tucked up in the wiring harness higher up in that same general area. The botton is recessed in a plastic ring (see diagram).
This button must be pressed while programming remotes or if the battery was disconnected and the lights are flashing.

Jan 05, 2011 | Subaru Impreza Cars & Trucks

1 Answer

I bought a new Keyless remote for a 2007 Forester from a Subaru Dealer to replace an original one that went bad after 2 years. I have followed the directions in the owner's manual to program it, but can't...


IMPREZA: 2005, 2006, 2007 and
FORESTER: 2005, 2006, 2007, 2008
Check for Immobilizer key on Forester XT models only.
information is always subject to change and correction imp05keylessremote1.jpg
new remote for 2005 Imprezas.
This is not the same remote as the 05 Legacy/Outback remote which also has truck/gate release on the front and a red panic button on the back.
Lock: press Lock button for 2 seconds or so to lock car, and arm optional security system. The car with chirp once and turn signals flash for locked, 5 short chirps and signal flashes if any door is not fully closed. The dome light goes on for 15 seconds and ignition key ring (if present) will light for 30 seconds when unlocked.
Unlock: press unlock one time for driver's door, press again within 5 seconds to unlock all doors inkling rear gate (wagon). The system does not open the trunk.
Panic mode: press and hold lock button for approx. 3-4 seconds to activate Panic mode. I panic model the horn honks and turn signals flash until either the lock or unlock button is pushed again.
Finder mode: Press lock button 3 times within 5 seconds to activate Vehicle Finder mode. The horn will honk once and the turn signals will flash 3 times
Distance: works within approx. 30 feet depending on battery strength, nearby concrete walls and etc.
Audible Chirp On-Off: the system will chirp when locked or unlocked. To turn OFF the chirps, unlock the door and then push both lock and unlock buttons at the exact same time for 2+ seconds. There will be 2 chirps indicating the the audible is off. To turn the chirp back on, repeat the process and the system will chirp one time when it is back on.
Battery: as the battery ages it will only work as you get closer to the car. When a battery is replaced, the transmitter must be re-synchronized with the Keyless control unit. To synchronize, press the lock or unlock button 6 times.
Programming: 4 codes may be programmed.
Sit in driver's seat and unlock all doors. Open and close the driver's door
Turn the ignition key from LOCK to ON position 10 times within 15 seconds. Be sure to stop at both lock and on. The horn will HONK once to indicate transmitter programming mode is activated. Leave key in LOCK position and don't remove it from ignition.
You now have 45 seconds to complete the programming as below.
Open and close driver's door again.
Push either lock or unlock button on the remote you want to program. The horn will honk 2 times when successful.
To continue and program other remotes at the same time: open and close the driver's door and push lock or unlock on the remote. The driver's door must be opened and closed between each remote you want to program.
Done programming? remove the key from the ignition and the horn will honk 3 times.
DELETE old codes? Reprogram 4 times, it will overwrite old codes.
Alarm Security System: optional on all models. When locked there is one chirp (can be turned off, see above), the turn signals will flash and the red 'security' light will start to flash once every 2 seconds except for STi which flashes twice every 2 seconds.
There will be 5 chirps if a door, hood, and trunk or gate is not fully closed
You can also arm the system by using the power lock button on the driver or passenger door as you get out of the car and then closing the door behind you.
Disarm the system: push unlock for 2 seconds
Lost remote, alarm activated? When you can't use a remote to turn off the system: open the door with a key or try to start the car and the horn will start to honk. Turn the key on-off 3 times within 5 seconds and the alarm will go off and you can start the car. It's simple!
VALET mode: To set valet mode or just to disable the security alarm system: 1. unlock all doors 2. physically open the driver's door 3. hold the UNLOCK button on remote for 2+ seconds. The red 'security' light will then flash 2 times a second until the car is turned on.
System has been Tripped (except for STi): if you unlock the door with the remote and it chirps the signal light flash 4 times, the system has been triggered;
Identification mode: To find out what happened and why the system was triggered:
Open and drivers door, leave it open. Turn ignition key from LOCK to ON 2 times and then leave in LOCK position.
Tripped code: 1 security light flash: a door has been opened, 3 flashes when the impact sensor was triggered, 4 flashes when the ignition was messed with or battery disconnected

Nov 19, 2009 | 2007 Subaru Forester 2.5X L.L. Bean...

1 Answer

Getting into the trunk


please have the door lock check out!- that is a mechanical problem in the lock!

Jun 18, 2009 | 2000 Ford Focus

2 Answers

Power door locks, radio, power trunk lock and remote not working


unfortunately i can only fix the "alternator wine": all you need is a ground loop isolator. it hooks up to your RCA cables in between the radio and amp. the only thing i can think for your other problems is fuses, unless somehow your factory radio controls those functions

Apr 27, 2009 | 2001 Honda Civic

1 Answer

Car alarm preventing car from starting


1999 CONCORDE: check the battery terminals probably they are not tight enough...something like that happened to me just the lights turned on and the car seemed to be dead, the battery is still ok since then. I just needed to buy new terminals.

Sep 20, 2008 | 1999 Chrysler Concorde

Not finding what you are looking for?
2000 Chrysler Concorde Logo

423 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...