Question about 1991 Toyota Previa

1 Answer

How do you change a front side light bulb - 1991 Toyota Previa

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 2,984 Answers

Turn Signal/Marker Light REMOVAL & INSTALLATION

  1. Remove the one retaining screw from the upper corner of the lens.
  2. Tape the end of a pry tool, then carefully extract from the bottom of the lens in a rocking motion till the stud is loosened from the retainer.
  3. NOTE: Do not pry from the back of the lens, this will crack the lens or damage the paint.
  4. Pull the lens assembly straight out from the body towards the front of the vehicle.
  5. Twist and remove the wiring from the back of the lens.
  6. Twist the bulb and remove it from the socket.
Fig. 5: Once the bulb is removed, inspect the socket for corrosion how do you change a front side light bulb - 90916p10.jpg
To install:
  • Before installing a light bulb into the socket, ensure that all electrical contact surfaces are free of corrosion or dirt. NOTE: Before installing the light bulb, note the positions of the two retaining pins on the bulb. They will likely be at different heights on the bulb, to ensure that the bulb is installed correctly. If, when installing the bulb, it does not turn easily, do not force it. Remove the bulb and rotate it 180 degrees from its former position, then reinsert it into the bulb socket.
  • Insert the light bulb into the socket and, while depressing the bulb, twist it 1/8 turn clockwise until the two pins on the light bulb are properly engaged in the socket.
  • To ensure that the replacement bulb functions properly, activate the applicable switch to illuminate the bulb which was just replaced. If the replacement light bulb does not illuminate, either it too is faulty or there is a problem in the bulb circuit or switch. Correct if necessary.
  • Install the socket and bulb assembly into the rear of the lens housing; otherwise, install the lens over the bulb.
  • Insert and secure the lens assembly into the body of the vehicle.
  • Posted on Jun 25, 2009

    Ad

    4 Suggested Answers

    6ya6ya
    • 2 Answers

    SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

    Hi,
    A 6ya expert can help you resolve that issue over the phone in a minute or two.
    Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
    The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
    click here to download the app (for users in the US for now) and get all the help you need.
    Good luck!

    Posted on Jan 02, 2017

    Ad
    • 5 Answers

    SOURCE: headlight bulb replacement & side marker light bulb replacement

    i think there are two flat guide pins that hold the headlight assembly in .. just pull them straight up ..and the assembly should come out ..hencse replace the bulbs.

    Posted on Jan 25, 2009

    • 119 Answers

    SOURCE: front driver side fog light out

    sounds like poor electrical contact around the bulb holder, or in the electrical plug to the foglamp unit. surface corosion to the terminals. try cleaning these contact surfaces with some emery tape or a very small screwdriver. you may also find bending the contacts very slightly in a way that makes them press harder against the bulb helps. if you have access to a test lamp check for a live feed to the contacts as well.

    Posted on Nov 09, 2009

    Zeevert
    • 373 Answers

    SOURCE: procedure to change turn signal light bulb on a

    Remove 3 or 4 of the plastic pins holding the inner fender. They are located around the lip of the fender opening. The pins are removed by pulling the center cap of the pin straight out about an 1/8" and then wiggle and pull the whole pin out.
    Pull the inner fender down and back.
    Reach your arm in and grab the socket and squeeze the locking tab.
    Rotate the socket counter-clockwise less than a quarter turn, and pull straight back.
    Reach your other hand in and remove the bulb by pulling it straight out of the socket. It takes a 3157 bulb

    Posted on Jun 22, 2010

    Testimonial: "Thank you so much for your help. Really I had ask the question about 3 months ago, but since I didn't had it fixed yet, it's OK now. Franco"

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    Side light change


    Use a plastic spudger to pry the side light out. Then you can open the light-housing and change the bulb. Check if it's working first. Make sure to clean both surfaces before popping the side light back in place.

    May 13, 2012 | 2005 Skoda Octavia 1.9

    1 Answer

    How hard is it to change a fog light bulb on a 2005 Subaru Forester? Can anyone do it?


    Front Fog Light Assembly

    REMOVAL


    1. Disconnect the ground cable from battery.
    105919447



    1. Remove the two clips and lower mudguard on side that bulb is being changed.
    2. Disconnect the harness connector from bulb on back of fog lamp.
    105919448




    Front Fog Light Bulb

    REMOVAL


    1. Locate back cover on fog lamp assembly where bulb is located inside.

    105919462



    1. Remove the back cover.
    105919463



    1. Remove the spring retainer, and then detach the fog light bulb.
    2. DO NOT TOUCH HALOGEN BULB!! Oils from skin will cause bulb to explode during operation.

    Jul 27, 2011 | Subaru Forester Cars & Trucks

    1 Answer

    How do I change a brake light bulb in a 1999 c70 volvo?


    Welcome to FixYa.com
    Brake Lamp Replacement

    Location of the lights

    Image

    The illustration shows the locations of the lights on the RH side. The LH side is the same but

    mirror-reversed.

    The lights have the following functions:

    - 1 +1 = Parking light Fail light

    - 2 = Reversing light

    - 3 = Fog light LH side only (LHD cars)

    - 5 = Direction indicator

    - 6 = Brake light

    Image

    Tail light changing bulbs

    Ignition off.

    Open the cover in front of the tail light

    Undo the wing nut and take out the lamp holder.

    Change the defective bulb.

    Fit in reverse order.

    Check that all bulbs lamps are intact and in working order.

    Image

    Replacement of tail light cluster

    Note! If a new tail light is to be fitted, the sleeves must be ground down 1.5 mm.

    Open the cover in front of the tail light Undo the panel partly in front of the tail light Unplug the

    connector for the tail light Undo the four nuts securing the tail light see illustration.

    Pull the tail light straight out. Fit in reverse order

    Note! check the sealing and fit on reassembly.

    Check that all bulbs lamps are intact and in working order.Thank you for Using FixYa.comKind Regards, LeeYour FixYa Expert and Master Technician

    Jan 27, 2011 | 1999 Volvo C70

    1 Answer

    Changing turn signal on front bumper


    All front light bulbs should be accessible, you will need to remove the 2 headlight bulbs...be sure to match the amber color if your Ciera still has the original bulbs:) The side marker light bulbs are reachable and can be changed by removing the 1 hold down bolt too...:)

    Dec 20, 2010 | 1991 Oldsmobile Cutlass Ciera

    1 Answer

    Driver front turn signal does not blink. front


    This may have more then one bulb in the front or possibly a bad socket try wiggling the new bulb in the socket to see if it will work.Compare all turn signal lights that come on the passenger side to those drivers side.Some vehicles also incorporate sidemarker lights with the turn signals.

    May 29, 2010 | 2001 Pontiac Aztek

    1 Answer

    How do you change a front signal bulb on a 2004 accord


    Front turn signal bulb replacement

    1. Remove the inner fender
    2. Disconnect the 3p connector from the front turn signal/side marker light.
    3. Turn the bub socket ( 45 degree ), counterclockwise to remove the bulb.
    4. Install a new bulb in the reverse order of removal.

    Apr 12, 2010 | 2004 Honda Accord

    1 Answer

    Where is the fuse for the right side tail light?


    hi if it is only the one bulb not working/tail light and the front light on same side is working along with number plate and other tail lights may i suggest you replace/check the bulb on defective light as if fuse had blown ? the front light on same side would not be working if you put ignition on and press brake your brake light shoul work ? if so change the bulb as the bulb has two elements inside tail light and a higher wattage element for brake light

    Feb 25, 2010 | 2004 Honda Accord

    2 Answers

    How to change the little front lights beside the main front light


    Side Marker Lights
    1. If visible, remove the attaching screws and partially remove the front side marker light lens.
    Fig. 7: To change a side marker bulb with no attaching screw, protect the body with a rag and gently pry the lens assembly outward . . .





    Fig. 8: . . . until the entire assembly is free of the body and access to the bulb socket is achieved


    2d8805f.jpgde76af4.jpg

    Aug 30, 2009 | 1994 Mazda 323

    4 Answers

    Front signal light not working and rear signal lights flashing fast on 1999 intrigue


    Your front turn signal socket is shot. Buy a new one at the dealer for about 30.00. It will fix it. You may be able to clean it and wiggle it to get it to work. But it wont last very long. I had the same problem. Replaced the socket and it is fine. Note: If one side is bad the other side it not far behind. Probably 2 or 3 months it will go also. Good Luck.
    Bill

    Apr 17, 2009 | 1999 Oldsmobile Intrigue

    1 Answer

    Cannot take casing off front side light bulb, need to change the bulb. Peugeot Partner van '02


    I want to change the side-light bulb on my Citroen Picasso off side front. I can get the near side one off, but find it difficult to turn the bulb holder inserted in the head light lens. Should I use some outside help like a HAMMER? Pete

    Mar 31, 2009 | 2006 Peugeot 604

    Not finding what you are looking for?
    1991 Toyota Previa Logo

    620 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    78267 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8836 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...