Question about 2000 Chrysler LHS

2 Answers

Replace low beam on 2000 LHS - 2000 Chrysler LHS

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

The headlight housing must be removed to access the bulbs on the back of the housing. HOWEVER!!! you must take loose the bumper on the side you are replacing. To do this you also have to take loose the inner finder and turn you wheel sharply in the opposite direction of the bulb to be replaced. There is a 10mm nut you will have to remove inside as well as multiple plastic fasteners along the inner finder and across the front under the hood. Bulb just twist out to remove once the housing is removed. Also, resist the urge to use a very large hammer. Use caution when pulling the plastic bumper out where the 10mm nut was removed, the stud can easily scratch the paint while working the housing out of its socket.

Posted on Jan 20, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 316 Answers

The headlight housing must be removed to access the bulbs on the back of the housing. 2. remove the retaining ring. Twist the retaining rings and slide them back over the harness. 3. withdraw the bulb assembly from the headlight housing. Twist and pull out the bulb holder and replace bulb. DO NOT TOUCH THE GLASS BULB!!!! If you do touch the glass, clean the glass part with rubbing alcohol. 4. Reinstall the way you took it apart.

Posted on Oct 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 Dodge Neon - the passenger side low beam will not come on. I've replaced the bulb but it still won't work. Both high beams and the driver side low beam are fine.


Check the wire right at the plug. This were they break the most. You have ground, because the high beam on that side works.

Feb 06, 2015 | 2000 Dodge Neon

2 Answers

Only one head light works in low beam, both works in high beam


Bulb is burned out, it has two filaments in it , low beam and high beam. Replace bulb!

Jan 12, 2011 | 2000 Honda Odyssey

1 Answer

Main beam not working on x reg mazda 626 full beam working ok


low beam burnt out,replace low beam bulb,if only one headlight,replace bulb

Dec 31, 2010 | 2000 Mazda 626

2 Answers

2000 impala-low beams don't work but high does


sounds like the problem is the dimmer switch, get a price on the dimmer switch. If you have to, get one at a junk yard . It's cheaper.

Dec 31, 2009 | 2000 Chevrolet Impala

1 Answer

Replaced cracked radiator in 2000 Chrysler LHS but car still overheating. What could be the problem?


fix the radiator first.because coolant temperature sensor need to be in antifreeze.when antifreeze get up to 190 degrees. the coolant sensor act as a thermostat.it resistance decrease then the pcm will command cooling fans to run.if antifreeze low the coolant temperature sensor not going to work. engine is going to over heat.

May 29, 2009 | 2000 Chrysler LHS

2 Answers

How do you replace the headlight bulb on a 2001 chrysler lhs.


This can be done buy popping the hood and removing the bulb from the rear of the headlight housing. don't screw with the housing because, its leveled for optimal sight range.

Jan 28, 2009 | 2000 Chrysler LHS

1 Answer

Both low beams will not come on


simmer switch would be the next on you list of thing that need checked out

Jun 25, 2008 | 2000 Porsche Boxster

Not finding what you are looking for?
2000 Chrysler LHS Logo

335 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...