Question about 2002 Dodge Intrepid

1 Answer

How to change break light?

How to change back break light?How to get cover off...

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 109 Answers

Pull the carpet back in the trunk, and you should see some black plastic wing nuts, un-screw those and the whole lamp assy should pop-out!!

Posted on Jun 26, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to remove tail lite cover on 2002 xteara

Open the back gate and you will see a couple of philips head screws. Unscrew them and snap the tail light out gently. There a couple of plastic clips that hold the tail light in place. Be careful not to break them (pull the light straight out not up, down, left, or right) Once the tail light cover is removed, separate it from the backing and reflective insert.To change the bulbs just twist counter clock wise and push in. Snap the new bulbs in and repeat the whole process in reverse.

Nov 15, 2010 | 2002 Nissan Xterra


How to change a headlamp in a mercedes benz c280

When changing a headlamp in a mercedes benz c280 1995. Lift the hood latch on the inside of the car. This is located under the driver side of the car. Release the hoodlatch in the front. Open the hood and behind the headlamp (left or right), Remove the two clamps that hold the back cover onto the light. After this cover is removed, behind the headlight there is a wire behind the light that hold the light in. Squeeze the two wires together and pull them back. This will release the light. Remove the light from the socket. Place the new bulb in the socket. Remember not to touch the bulb with your fingers, this could cause the bulb to break if it gets the oil from your fingers onto the bulb. Once the bulb is replaced, put the wire back in place and replace the back cover of the light.

on Nov 27, 2010 | Mercedes-Benz C-Class Cars & Trucks

1 Answer

How do you remove the cover to change the break lights on the back left corner of a 1994 chevy suburban?

Two hex head screws hold the external glass in place, check the rubber seal as it has to go back.

Nov 28, 2009 | 1994 Chevrolet Suburban

2 Answers

My oil light blinks on when I press on the breaks. It has pleanty of oil & was changed about 2 months ago. What could the problem be?

see if their is a rubber cover over the oil light switch?? if their is pull it back because the oil has weeped out the switch into the cover and then earthing the itself throwing the light on

Nov 20, 2009 | 2006 Kia Spectra

1 Answer

How do you take the cover off the break lights to change bulb

with the trunk open, there will be 2 or 3 screws holding the light assembly onto the car.. remove the screws and the assembly will pop out... then twist the socket in the back of the assembly and the light bulb will pop out

Aug 20, 2009 | 2001 Dodge Caravan

1 Answer


well u have to take out the head light clips which are on the sides of the head light then pull out the head light and uncover the second rubber cover i believe then reach in the head light and turn the socket to the left and and should come out the just change the bulb...when putting the bulb back just turn it to the right and put back the head light and rubber cover and the side clips and thats it...good luck

Jun 22, 2009 | 1988 Buick Century

1 Answer

Replacing tail light on Jeep Liberty

So you already have the screws out. You simply have to pull it out. It probably have a small plug or *** on the back side to help hold it in place. YOu can pull the unit fairly hard on it with out breaking it, just be firm with it and it should come right out. I'm not sure about the 3rd light, how it is mounted as well. Are you just changing the light bulb in it or changing the cover? If your just changing the bulb or cover you should just be able to take the screws out of the cover and use a small screwdriver to gnetly pry it off.

Apr 28, 2009 | Jeep Liberty Cars & Trucks

1 Answer

How do i change a break light in a 89 buick electra?

turn the black wing nuts to remove taill lamp

Mar 14, 2009 | 1989 Buick Electra

1 Answer

I need to replace rear break light (driver side) on pacifica 04

if there aren't any screws on the out side, you'll have to gain access from the trunk.

Dec 02, 2008 | 2005 Chrysler Pacifica

1 Answer

Get back door open to change break lights

from inside, at the center bottom of the back door there should be a button covering a 1" hole. If you look inside with a flashlight you will see the linkage coming from the handle, with a straight screwdriver or a prybar gently lifting on the latch while pushing out on the door should give you success. . It Just worked for me.

Oct 14, 2008 | 1996 Dodge Caravan

Not finding what you are looking for?
2002 Dodge Intrepid Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides