Question about 1992 Toyota Pickup

1 Answer

Brand new starter solinoid clicks just like the

Brand new starter solinoid just clicks just like the old one but intermitently will work

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Sounds like you have a bad battery conection. clean all the conections. if that does,nt work your battery may be no good.

Posted on Jul 26, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Just fixed the starter on my 2007 cobalt, but it still will not start. Lights work I had it start twice since the starter was fixed and still nothing. you hear the batter and a click sound like its...

Sounds like possbly your old starter might have been good starting solinoide is bad, did you replace both starte and soliniode if not replace the starting soliniode should fix problem. If you bought a rebuild it might be bad. take it to Auto Zone they can test both the solinoide and starter.

Oct 04, 2013 | Chevrolet Cobalt Cars & Trucks

1 Answer

Starter replacement, how to r@r starter

First you unhook the battery neg side first then pos side then you remove the wires from the starter solinoid make a mental note so you know how to hook it back up then take out the two starter bolts holding it remove old starter put new one in put the two starter bolts in then put wires back on the solinoid hook the battery back up and your done.

Jul 03, 2011 | 1999 Chevrolet Malibu

2 Answers

I just replaced my starter in my 92 ford ranger, it worked fin for a bit, now it just clicks again battery is new.

Perhaps you purchased a defective one it wouldn't be the first time i seen that happen.

Dec 26, 2010 | 1992 Ford Ranger

1 Answer

I just bought this ram truck with the V10 8.0 and it has been sitting for about 9 months in a barn. I replaced the battery and now the starter just clicks. At first it did roll the engine just a couple of...

if it just clicks when trying to start. then most likely its the starter solinoid. the solinoid is what pushes gear out to meet flywheel when starting. its up to you, you can replace starter or just the solinoid. but it would be in your best interest to change whole starter. then you know it will be ok. have a good day !!

Dec 25, 2010 | 1995 Dodge Ram 2500

1 Answer

90 vette, ZR-1, Engine won't crank. Solinoid won't click. Worked fine since new. Washed engine, started & drove into garage, 2 days later won't crank. Has 30,000 miles, owned since new. Batt....

Never wash engine in zr-1,starter is in center of engine,drain hole is usually plugged up,starter has shorted out,will need new starter,clean drain hole out when it is changed

Nov 06, 2010 | 1990 Chevrolet Corvette

2 Answers

Turn key battery full good starter nothing dimms down just like i am not turning the key

check the wiring to the starter sounds like your starting wiring is not making good contact if not test with a test light and check the fuse hope this helps

Sep 11, 2010 | 1990 Chrysler Imperial

3 Answers


hi, this is the solinoid contacts (BURNED OUT). there are 2 parts to the solinoid (HEAVY SWITCH) connects BATTERY to STARTER MOTOR. the other part of the SOLINOID is IGNITION KEY TURN TO SOLINOID the wiring to this part is working. (by changing the solinoid this will work). thank you gerry

Sep 10, 2010 | Kia Sportage Cars & Trucks

1 Answer

I have a 1969 mustang 302 v8 auto, i installed a different starter with 3 terminal, a pos, a lead, and one already fixed on the starter.... i connected the pos and 2 bolts..nothing happens, it clicks the...

the older fords used a remote solinoid. the big terminal is a power all the time. the small one is the energizer and only gets hot when the key is in the start position. the third one that goes to the starter motor its self turns the motor. on the old solinoid on the fender you should find a small wire hooked to it hat only gets hot when you turn the key to start.lenghten it and attach to the small terminal on the starter. i would however see if you cant get the correct starter first, for it in my opinoin is the better system

Jan 31, 2010 | 1966 Ford Mustang

1 Answer

1994 jaguar xjs just clicks when i try to start it-battery is new. The starter bad?code was RR39

If there is a power drain - new battery or old - it needs to be well charged to start the car..
If the batt is charged well - it could be the starter solinoid or the starter..
However - the typical "clicking sound" is usually a low battery..
IF the batt is low - could be the charging sytem or a power drain ..

Jul 08, 2009 | 1998 Jaguar XJ8L

1 Answer

Starter or solinoid?

I never heard of a starter solonoid coming with shims. Did you replace the starter or starter solonoid?
What engine do you have?

Nov 20, 2008 | 1994 Jeep Wrangler

Not finding what you are looking for?
1992 Toyota Pickup Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides