Question about 2001 Daewoo Nubira

1 Answer

Need to know how to align the crankshaft when the mark is not there.

Posted by on

  • grumpygump Jun 26, 2009

    I took the tensioner all the way off and I need to know how to put it back on

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Daewoo Master
  • 76,846 Answers

THIS IS THE TIMING BELT REPAIR PROCEDURE, ALL THE INFO IS THERE THAT U NEED AND MORE..
Required tools:
13mm open end wrench 10mm shallow and deep socket 8mm socket long flathead screwdriver 17mm deep socket T50 torx socket 1/4", 3/8ths and 1/2" ratchets and extensions E10 inverted torx sockets 6mm Allen wrench 15mm open end wrench 7mm socket 12mm open end wrench 14mm socket 12mm socket 8mm, 9mm and 10mm Allen head sockets 19mm socket pry bar needle nose pliers
If you are doing this because your timing belt broke you will also need to buy a complete cylinder head, head gasket set, and both idler pulleys. ALL DAEWOO MODELS WILL BREAK THE INTAKE AND EXHAUST VALVES WHEN THE TIMING BELT BREAKS.
Start by removing the air cleaner assembly from the throttle body, remove the air filter and housing jack up the vehicle and remove the wheel, remove the plastic shielding in front of the accessory drive belt assembly, remove the accessory drive belt, place a jack with a block of wood on top underneath the engine oil pan remove the front engine mount, remove the crank shaft pulley ( the 4 Allen head bolts only not the 17mm bolt in the center.) remove the metal plate behind the engine mount bracket on the engine, remove the plastic timing belt cover 3 clips on top 2 10mm bolts on bottom. Rotate the engine until the #1 cyl. is at Top Dead Center on the compression stroke or line up the crankshaft timing mark with the mark on the inner timing belt cover ( notch in cover with notch in pulley) on the camshaft pulleys -- ( intake cam line up the line on the pulley with the line on the inner cover)( exhaust cam line up the arrow on the pulley with the arrow on the inner cover) loosen the 13mm bolt in the belt tensioner and using the Allen wrench rotate the tab until there is slack in the belt. Remove the belt. At this time I would recommend you replace the water pump, both plastic idler pulleys as they tend to overheat and lockup, and the belt tensioner. Make sure all your marks are lined up, you may need a helper to hold the Exhaust Cam in place as it tends to move during belt installation. Put the timing belt underneath the crankshaft pulley, install the belt leaving the intake cam for last and NO BELT SLACK on the right side between the crank and the exhaust cam. Once the belt is installed rotate the crankshaft over 2 revolutions and make sure is rotates freely, and your timing marks are aligned perfectly if not the engine will not run properly, tension the belt as needed. Installation is the same as removal.

To clarify, on the DOHC engine, the intake cam gear has a line on it, and the exhaust cam gear has an arrow on it. These should be lined up with the corresponding line and arrow on the VALVE COVER, pointing straight up. I just went through this process over the weekend, and spent quite a bit of time looking for these marking as I had removed the valve cover. Once I found them, it was plain and simple.
In addition, be sure to not over tighten the belt when reinstalling. The tensioner has markings on it for "old" and "new". DO NOT adjust past "new", as the car will sound like a jet engine, and the belt will not last for very long.
One more item that you may as well replace while you are in there is the cam position sensor if you have not already, as there have been issues with them, and the timing housing has to be opened to get to it

Posted on Jun 25, 2009

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 8 Answers

SOURCE: crankshaft pulley timing marks

http://www.manualnguide.com/download/manual-guide/honda-civic-1988-1990-service-manual.html

Posted on Sep 01, 2008

  • 23 Answers

SOURCE: how do you align the camshaft & crankshaft timing marks 1.9

This is the same as a Ford Escort 1.9, the #1 cylinder should be all the way up. To confirm- the crak shift mark should be on zero which is Crank Shift Center- THe camshift sproket should align with the headmark. Make sure both marks don't move. Align the belt- not too tight , not to loose

Posted on Jul 12, 2009

  • 5 Answers

SOURCE: Timing belt. 1990 2.3 liter 4 cyl. Crankshaft

there should be a mark on the crankshaft pulley there should be a mark on the camshaft pulley and they should line up but to be sure bring the motor to tdc then line your mark up on your camshaft

Posted on Aug 26, 2009

emissionwiz
  • 76846 Answers

SOURCE: 1992 Volvo 960 Broken timing belt

IF U BROKE THIS BELT WHILE DRIVING U HAVE BENT THE VALVES IN THE ENGINE, THIS IS WHAT IS CALLED AN INTERFERENCE DESIGN ENGINE, THAT MEANS WHEN THE TIMING BELT BREAKS THE PISTONS HIT THE ENGINES VALVES

Posted on Nov 11, 2009

Testimonial: "THanks - was not able to accept this last answer, but thankfully I found another way to say THANKS. That notch was suspicious!"

  • 1757 Answers

SOURCE: You are changing the timing belt and you need o

Click on the following free direct Link. It has the Timing: Belt and Mark Diagrams for your 1994 Toyota Corolla. Plus additional Instructional and Directional Diagrams.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1994/make/toyota/model/corolla/1994_toyota_corolla_timing_belt_diagram_marks.htm

Posted on Mar 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Matching the sprokets pionts with the camshaft levels


Timing marks 2000 Toyota corolla (4E-FE/ 4A-FE/ 5A-FE)

1c8f15cd-1b11-4540-8ded-ce3f879ea3c3.jpg
Align the crankshaft pulley mark with the 0 mark of timing case.
8f3eb447-5885-434e-a05e-4bf613d93b45.jpg
The camshaft sprocket is at TDC when the hole in the sprocket lines up with the notch in the bearing cap

Timing marks 2000 Toyota Corolla (1ZZ-FE/ 3ZZ-FE/ 4ZZ-FE/ 2ZZ-GE)
388d4776-148a-40e2-bc7f-22e918bb72ef.jpg
Set the Crankshaft key in 12 'o Align yellow timing chain mark
Clock position (The key aligns on the crankshaft sprocket
with the mark on the oil pump (see arrow)
body (see arrow mark)
41828b9e-e992-4622-bfca-450c5357f236.jpg
Align the marks on the sprockets Place the crankshaft angle plate
with the yellow links of the timing with the marks B or F, facing
chain. towards you.

Jan 18, 2014 | 2000 Toyota Corolla

1 Answer

I have this 89 acura legend 2.7l v6 timing belt removed and the water pump removed, the old pump failed which caused the belt to fail, i have new parts and the pump installed only i dont understand to...


Hi, here is what you need to do. Get all of the timing marks lined up as indicated in the picture below. Put the belt on. Without moving the gears off their marks, make the belt tight across the cam gears and then down the right side to the crank gear. All of the slack must be on the left side to be taken up by the tensioner. Release the tensioner to tighten the belt and then verify the marks are still aligned. If the marks are not aligned, loosen the tensioner just enough to turn the gear that needs to be realigned. After tensioning the belt, rotate the crankshaft clockwise 720 degrees and recheck the timing marks. I have pasted the book procedure below. Please let me know if you still have questions. You must get this right.

jturcotte_2242.gif

jturcotte_2243.gif



jturcotte_2244.gif



jturcotte_2241.gif

  1. If the crankshaft or camshafts have been turned with the timing belt removed, remove the spark plugs and advance the crankshaft about 15 degrees beyond TDC of No. 1 cylinder. Make sure the camshaft sprockets are properly aligned with the marks and return the crankshaft to the TDC mark.
  2. Install the belt in sequence on the crankshaft, the front camshaft, water pump and tensioner pulleys, then the rear camshaft.
  3. To adjust the tension, loosen the tensioner pulley bolt about 1 / 2 turn. The spring will automatically set the proper tension. Torque the bolt to 31 ft. lbs. (43 Nm).
  4. Rotate the crankshaft 6 turns clockwise and check that the timing marks on the crankshaft and camshafts align properly. Adjust the timing belt tension again by rotating the crankshaft to the align the blue mark on the pulley with the pointer. Loosen and retorque the tensioner pulley bolt.
  5. Install the remaining parts in reverse order. Torque the crankshaft pulley bolt to 83 ft. lbs. (115 Nm). When installing the side mount bracket, torque the bolts to 40 ft. lbs. (55 Nm).

Sep 13, 2011 | Acura Legend Cars & Trucks

1 Answer

Like to know where the timing mark for a 2006 chrysler sebring


Hi, here you are...
39900a5.gif Crankshaft and camshaft alignment marks-2.4L (VIN X) Engine


9f5c6e9.gif
Camshaft and crankshaft alignment marks-Chrysler 2.5L (VIN N) engine


acb6bd1.gif
Timing belt engine sprocket timing-2.5L (VIN H) engine

Feb 13, 2011 | 2006 Chrysler Sebring

1 Answer

Como poner la banda de tienpo de un toyota camery


Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence.

Dec 23, 2010 | 1993 Toyota Camry V6

1 Answer

2005 f250 5.4 gas need to know specs for timing a diagram would be awesome


To Install:
  1. Install balance shaft drive gear onto the left camshaft.
  2. Install the camshaft sprockets and new bolts finger tight.
  3. Using a vise, compress the timing chain tensioner plunger.
  4. Install a retaining clip on the tensioner to hold plunger IN during installation.
    marking timing chain a0038720.gif

  5. If timing chain copper links are not visible, mark 2 links on one end and 1 link on the other end to be used as timing marks.
  6. Install right and left timing chain guides. Tighten bolts to 89 in-lbs (10 Nm).
  7. Rotate the left camshaft until the timing mark is at the 12 o'clock position.
  8. Rotate the right camshaft until the timing mark is at the 11 o'clock position.
  9. Position the crankshaft using the special tool. Then remove the tool.
    Crankshaft special tool positioning n0013602.gif

  10. Install the crankshaft sprocket with flange facing forward.
    Crankshaft sprocket timing mark n0011528.gif

  11. Position lower end of left (inner) timing chain on the crankshaft sprocket. Align the copper (or marked) chain link with the timing mark on the outer flange of the crankshaft pulley. NOTE: Upper half of timing chain must be below the tensioner arm dowel.
  12. Position the left timing chain on the camshaft sprocket. The timing mark on the camshaft sprocket must be aligned between the 2 copper (or marked) chain links.
    Left camshaft sprocket timing mark a0080774.gif

  13. Place the left timing chain tensioner arm on the dowel pin and install the timing chain tensioner and bolts. Tighten bolts to 18 ft-lbs (25 Nm). NOTE: Lower half of timing chain must be above the tensioner arm dowel.
    Crankshaft sprocket timing mark a0079624.gif
  14. Position lower end of right (outer) timing chain on the crankshaft sprocket. Align the copper (or marked) chain link with the timing mark on the outer flange of the crankshaft pulley.
    Right camshaft sprocket timing mark a0041104.gif

  15. Position the right timing chain on the camshaft sprocket. The timing mark on the camshaft sprocket must be aligned between the 2 copper (or marked) chain links.
  16. Place the right timing chain tensioner arm on the dowel pin and install the timing chain tensioner and bolts. Tighten bolts to 18 ft-lbs (25 Nm).
  17. Remove the retaining clips from the right and left timing chain tensioners.
  18. Verify alignment of all timing marks.
  19. Install crankshaft sensor ring on crankshaft.
  20. Locate index mark on balance shaft and mark corresponding gear tooth with chalk.
  21. Position balance shaft on journals. NOTE: It may be helpful to use an inspection mirror to view the marks timing marks.
  22. Align the chalk mark on the balance shaft with the camshaft timing mark.
    Balance shaft bearing caps n0007112.gif

  23. Install the balance shaft bearing caps in their original locations. Follow the tightening sequence as shown in the illustration. Tighten bolts to 89 in-lbs (10 Nm).
  24. Tighten the camshaft phaser sprocket bolts in the correct sequence using 2 steps, as follows:
    • Step 1-30 ft-lbs (40 Nm)
    • Step 2-tighten an additional 90 degrees
  25. Position the crankshaft keyway in the 11 o'clock position.
  26. Lubricate and install all camshaft roller followers. WARNING
    Engine front cover replacement procedure must be completed within 4 minutes or entire procedure must be repeated. Failure to do so may result in future leaks

Oct 07, 2010 | Ford F-250 Cars & Trucks

2 Answers

2000 dodge caravan V6 3.0L interference or not??


Timing chain is only available in the 3.3L and 3.8L engines.

Yours has a belt. (if you're SURE its a 3.0L)

Here is the info on changing it...

3.0L Engine
The timing belt can be inspected by removing the upper front outer timing belt cover.
Working on any engine (especially overhead camshaft engines) requires much care be given to valve timing. It is good practice to set the engine up at TDC No. 1 cylinder firing position before beginning work. Verify that all timing marks on the crankshaft and camshaft sprockets are properly aligned before removing the timing belt and starting camshaft service. This serves as a point of reference for all work that follows. Valve timing is very important and engine damage will result if the work is incorrect.
  1. Disconnect the negative battery cable.
  2. Remove the accessory drive belts. Remove the engine mount insulator from the engine support bracket.
  3. Remove the engine support bracket. Remove the crankshaft pulleys and torsional damper. Remove the timing belt covers.
  4. Rotate the crankshaft until the sprocket timing marks are aligned. The crankshaft sprocket timing mark should align with the oil pump timing mark. The rear camshaft sprocket timing mark should align with the generator bracket timing mark and the front camshaft sprocket timing mark should align with the inner timing belt cover timing mark.
  5. If the belt is to be reused, mark the direction of rotation on the belt for installation reference.
  6. Loosen the timing belt tensioner bolt and remove the timing belt.
  7. If necessary, remove the timing belt tensioner.
  8. Remove the crankshaft sprocket flange shield and crankshaft sprocket.
  9. Hold the camshaft sprocket using spanner tool MB990775, or equivalent, and remove the camshaft sprocket bolt and washer. Remove the camshaft sprocket.
  10. To install:
  11. Install the camshaft sprocket on the camshaft with the retaining bolt and washer. Hold the camshaft sprocket using spanner tool MB990775, or equivalent, and tighten the bolt to 70 ft. lbs. (95 Nm).
  12. Install the crankshaft sprocket.
  13. If removed, install the timing belt tensioner and tensioner spring. Hook the spring upper end to the water pump pin and the lower end to the tensioner bracket with the hook out.
  14. Turn the timing belt tensioner counterclockwise full travel in the adjustment slot and tighten the bolt to temporarily hold it in this position.
  15. Rotate the crankshaft sprocket until its timing mark is aligned with the oil pump timing mark.
  16. Rotate the rear camshaft sprocket until its timing mark is aligned with the timing mark on the generator bracket.
  17. Rotate the front (radiator side) camshaft sprocket until its mark is aligned with the timing mark on the inner timing belt cover.
  18. Install the timing belt on the crankshaft sprocket while keeping the belt tight on the tension side.
  19. Position the timing belt over the front camshaft sprocket (radiator side). Next, position the belt under the water pump pulley, then over the rear camshaft sprocket and finally over the tensioner.
  20. Apply rotating force in the opposite direction to the front camshaft sprocket (radiator side) to create tension on the timing belt tension side. Check that all timing marks are aligned.
  21. Install the crankshaft sprocket flange.
  22. Loosen the tensioner bolt and allow the tensioner spring to tension the belt.
  23. Rotate the crankshaft 2 full turns in a clockwise direction. Turn the crankshaft smoothly and in a clockwise direction only.
  24. Align the timing marks. If all marks are aligned, tighten the tensioner bolt to 250 inch lbs. (28 Nm). Otherwise repeat the installation procedure.
  25. Install the timing belt covers. Install the engine support bracket. Tighten the support bracket mounting bolts to 35 ft. lbs. (47 Nm).
  26. Install the engine mount insulator, torsional damper and crankshaft pulleys. Tighten the crankshaft pulley bolt to 112 ft. lbs. (151 Nm).
  27. Install the accessory drive belts and adjust them to the proper tension.
  28. Reconnect the negative battery cable.
  29. Run the engine and check for proper operation. Road test the vehicle.
Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Feb 18, 2010 | 2000 Dodge Caravan

1 Answer

I need timing specs for 1994 dodge intrepid 3.5 For a new timing belt I need to know how to align the gears and crank shaft.


Crankshaft sprocket mark aligns with TDC indicator just above it, and camshaft mark, goes in center of 2 marks on back cover behind them.05fb1b8.gif

Oct 31, 2009 | 1994 Dodge Intrepid

1 Answer

Timing for tropper 6cly and 4 camshafts and 24 valves model 2000


Timing Belt
Removal
1. Disconnect battery ground cable.
2. Remove air cleaner assembly.
3. Remove radiator upper fan shroud from radiator.
4. Move drive belt tensioner to loose side using wrench
then remove drive belt.
850RW001
Legend
(1) Crankshaft Pulley
(2) Cooling Fan Pulley
(3) Tensioner
(4) Generator
(5) Air Conditioner Compressor
(6) Power Steering Oil Pump
(7) Drive Belt
5. Remove cooling fan assembly four nuts, then the
cooling fan assembly.
6. Remove cooling fan drive pulley assembly.
7. Remove idle pulley assembly.
8. Remove serpentine belt tensioner assembly.
9. Remove power steering pump assembly.
10.Remove crankshaft pulley assembly using
5–8840–0133–0 crankshaft holder, hold crankshaft
pulley remove center bolt, then the pulley.
11. Remove right side timing belt cover then left side
timing belt cover.
12. Remove lower timing belt cover
13. Remove pusher.
CAUTION: The pusher prevents air from entering
the oil chamber. Its rod must always be facing
upward.
014RW011
Legend
(1) Up Side
(2) Down Side
(3) Direction For Installation
(4) Locking Pin
14. Remove timing belt.
CAUTION:
1. Do not bend or twist the belt, otherwise its core
could be damaged. The belt should not be bent at
a radius less than 30 mm.
2. Do not allow oil or other chemical substances to
come in contact with the belt. They will shorten
the life.
3. Do not attempt to pry or stretch the belt with a
screw driver or any other tool during installation.
4. Store timing belt in a cool and dark place. Never
expose the belt direct sunlight or heat.
6A–30 ENGINE MECHANICAL
Installation
NOTE: For correct belt installation, the letter on the belt
must be able to be read as viewed from the front of the
vehicle.
014RY00042
Legend
(1) Crankshaft Timing Pulley
(2) RH Bank Camshaft Drive Gear Pulley
(3) Water Pump Pulley
(4) Idle Pulley
(5) LH Bank Camshaft Drive Gear Pulley
(6) Tension Pulley
014RY00043
Legend
(7) Alignment Mark on Oil Pump.
(8) Alignment Mark on Timing Belt
(9) Alignment Mark (notch) on Crankshaft Timing
Pulley.
(10) Alignment Mark (groove) on Crankshaft Timing
Pulley.
014RW006
Legend
(1) Timing Belt
(2) Engine Rotation Direction
(3) Cylinder Head Side
1. Install timing belt.
1. Align the mark (notch) of crankshaft timing pulley
(2) with mark on oil pump (1).
Align the mark (groove) on the crankshaft timing
pulley (3) with alignment mark (white dots line) on
the timing belt (4).
NOTE: When timing marks are aligned, No.2 piston will
be on Top Dead Center.
014RW003
Legend
(1) Alignment Mark on Oil Pump
(2) Groove on Crankshaft Timing Pulley
(3) Alignment Mark on Crankshaft Timing Pulley
(4) Alignment Mark on Timing Belt
ENGINE MECHANICAL 6A–31
2. Align the alignment mark on the RH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover RH (3).
3. Align the alignment mark (white line) on the timing
belt (1) with alignment mark on the RH bank
camshaft drive gear pulley (2) (on the left side as
viewed from the front of the vehicle) and put the
timing belt on the camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
014RW00004
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover RH.
4. Align the alignment mark on the LH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover LH (3).
5. Align the alignment mark (white line) on the timing
belt (1) with the alignment mark on the LH bank
camshaft drive gear pulley (2).
When aligning the timing marks, use a wrench to
turn the camshaft drive gear pulley, then set the
timing mark between timing belt and camshaft
drive gear pulley and put the timing belt on the
camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
NOTE: It is recommended for easy installation that the
belt be secured with a double clip or equivalent clip after
it is installed the timing belt to each pulley.
014RW00005
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover LH.
6. Install crankshaft pulley temporarily and tighten
center bolt by hand (do not use a wrench).
Turn the crankshaft pulley clockwise to give some
belt slack between the crankshaft timing pulley
and the RH bank camshaft drive gear pulley.
2. Install pusher and tighten bolt to the specified torque.
Torque : 25 N·m (2.5 Kg·m/18 lb ft)
1. Install the pusher while pushing the tension pulley
to the belt.
2. Pull out pin from the pusher.
NOTE: When reusing the pusher, press the pusher with
approximately 100Kg to retract the rod, and insert a pin
(1.4 mm piano wire).
014RW011

Mar 18, 2009 | 2000 Isuzu Trooper

2 Answers

Need instructions to replace 1993 Toyota Camry Timing Belt


Hi Kmcarroll77

TIMING BELT REPLACEMENT - 2.2L -1993 Toyota Camry

Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence. See Fig. 6 . On MR2, tighten engine
b7619be.jpg
92cabaf.jpg
Hope this helps, don't forget to rate.

Lazaruselite

Feb 25, 2009 | 1993 Toyota Camry V6

1 Answer

2004 Durango 5.7 timing gear alignment


  1. If tensioner assembly is being replaced, install tensioner and mounting bolts. Torque bolts to 28 Nm (250 in. lbs.) .
  2. Retract tensioner if required. CAUTION: The camshaft pin and the slot in the cam sprocket must be clocked at 12:00. The crankshaft keyway must be clocked at 2:00. The crankshaft sprocket must be installed so that the dots and or paint marking is at 6:00.
  3. Place both camshaft sprocket and crankshaft sprocket on the bench with timing marks on exact imaginary center line through both camshaft and crankshaft bores.
CAUTION: The timing chain must be installed with the single plated link aligned with the dot and or paint marking on the camshaft sprocket. The crankshaft sprocket is aligned with the dot and or paint marking on the sprocket between two plated timing chain links.
b04dbf8.jpg

Feb 13, 2009 | 2004 Dodge Durango

Not finding what you are looking for?
2001 Daewoo Nubira Logo

473 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...