Question about 1998 Jeep Grand Cherokee

1 Answer

How do i chang my front axle from my 97 grand cherokee ltd

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

Let's have a few more detials...???

Posted on Jun 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I remove and install hubs on the front end of a 97 jeep grand cherokee?


It is actually very easy. Lift the vehicle and support it properly remove the 5 lug nuts retaining the wheel. Remove the wheel. If it is a 4 wheel drive remove the spindle nut locking the c.v. axle to the hub. Remove the washer. Push the axle through the splined hub. using a 13 mm or 15mm depending on the hub remove the three bolts reatining the hub assemble to the steering knuckle. assemble in reverse order.

Feb 27, 2011 | 1997 Jeep Grand Cherokee

1 Answer

97 jeep. Removing front wheel bearing


Most times you can squirt some wd40 on the ends of the axle spline, then put the axle nut on backwards so the castellated side is towards the bearing hub and run it onto the threads till the axle and nut are flush. (So you don't damage the threads or mushroom the end of the axle.) Once you have done that you can give it a really hard shot with a decent sledge hammer (two lb or heavier) striking it as squarely as possible. I have never had one refuse to come apart when I do this!!!

Feb 08, 2010 | 1997 Jeep Grand Cherokee

1 Answer

How do I change the front and rear shocks on my 99 cherokee?


FRONT:
Removal & Installation
  1. Remove the nut, retainer and grommet from the shock stud in the engine compartment.
  2. Raise and support the front axle.
  3. Remove the lower mounting nuts from the axle bracket.
  4. Remove the shock absorber.
To install:
  1. Position the lower retainer and grommet on the shock stud. Insert the shock absorber through the shock tower hole.
  2. Install the lower shock studs into the axle bracket.
  3. Install the mounting nuts and tighten to 250 in. lbs. (28 Nm).
  4. Remove support and lower the vehicle.
  5. Install the upper grommet, retainer and nut on the stud in the engine compartment.
Rear:

Removal & Installation
  1. Before servicing the vehicle, please familiarize yourself with safety procedures.
  2. Remove or disconnect the following:
    • Upper locknut and washer from the frame bracket stud, on the Grand Cherokee
    • Lower bolt, nut and washers from the axle shaft tube bracket
    • Shock absorber
To install:
  1. Place the shock absorber upper end in position and tighten the fasteners to the following specifications:
    • Cherokee: 17 ft. lbs. (23 Nm)
    • 1999–01 Grand Cherokee:68 ft. lbs. (92 Nm)
    • 2002–04 Grand Cherokee: 80 ft. lbs. (108 Nm).
    • 2005 Grand Cherokee: 70 ft. lbs. (95 Nm).
  2. Place the shock absorber lower end in position and tighten the fasteners to the following specifications:
    • Cherokee: 46 ft. lbs. (62 Nm)
    • 1999–01 Grand Cherokee:68 ft. lbs. (92 Nm)
    • 2002–05 Grand Cherokee: 115 Nm (85 Nm).
    please do not hesitate to ask any further questions about your vehicle i would be glad to help you.
  3. do not forget to rate and comment about your experience with fixya...


Dec 27, 2009 | 1999 Jeep Cherokee

2 Answers

My 97 jeep grand cherokee makes a chirping sound under front


The noise and the light may or may not be related. The noise may be the wear indicator on the brake pads touching the rotor (they are supposed to do that when brakes are worn) The abs light triggers off a wheel on the axle end. If you have a bad joint on the axle, it could be noisy and causing the wheel to not have the proper clearance to the abs sensor. You really need to take the wheel and brake assembly off and carefully inspect everything. Make sure all abs sensor wires are undamaged...it doesn't have to be at the same wheel that's chirping.

Sep 26, 2009 | 1997 Jeep Grand Cherokee

1 Answer

Need help on changing the front right cv joint axle shaft on my 1999 grand cherokee


remove wheel and tire caliper and rotor axle nut hub bearing pull axle out of spindle slide new axle in and reverse procedure

Aug 05, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Jeep GC axle oil change


undo the lower plug on your diff housing,drain tighten plug up, undo top plug fill til overflow,same as front,oil refer to owners manual or call local service centre

Jan 05, 2009 | 1996 Jeep Grand Cherokee

1 Answer

REPLACE 97 JEEP GRAND CHEROKEE REAR WHEEL BEARINGS


What you do is push the axle inboard in which gives you access to the clip and use a magnate to remove the clip.

Jun 30, 2008 | 1997 Jeep Grand Cherokee

Not finding what you are looking for?
1998 Jeep Grand Cherokee Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...