Question about 2000 Honda Accord

1 Answer

Replace left brake light/tail light bulb - 2000 Honda Accord

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 716 Answers

The Are Accessed From The Inside Remove The Carpet And Or Panel Directly Behind The Light On The Inside And You Will See The Light Assembly. Once You Find It Turn The Harness Counter Clockwise To Remove And Clockwise To Reinsert.
Sincerely,
Michael Scott

Posted on Jul 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1999 Dodge Ram 1500 - Right rear tail light won't burn for tail lights alone, but will still blink for turn signal and light up for brakes. Bulb was replaced with no effect. Left still works.


The bulb has two filaments; one for brakes and turn signal, the other for tail lights. One filament is probably burned out. Replace the bulb with a new one

Aug 09, 2017 | Dodge Cars & Trucks

1 Answer

How do i replace left rear brake light bulb


1) Open trunk
2) Remove small round plastic access panel with a flat tip screw driver by prying open
3) Remove flat tip screw holding tail light assembly
4) Remove tail light assembly by pulling outward, careful not to break plastic guide/nub
5) Disconnect wiring connectors
6) Remove plastic housing access plate on back of tail light assembly by twisting/turning tabs until they click and then lift access plate from tail light assembly
7) When viewing the the bulbs, the turn signal bulb is the bottom left bulb
8) Install in reverse order, ensuring tail light seal seats properly during installation

Oct 13, 2014 | 1999 Audi A4

2 Answers

2007 chevy impala brake light and left turn signal not working


Fast flashing dash signals mean there is a bulb issue-DEFINATELY!

Aug 07, 2012 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

Headlight switch on makes tail light dim


there must be a short circuit which powers tail lights and brake lights. probably you have a dual filament bulbs which have both brake and tail light together. check for bulb, socket/or bulb housing and harness of that light.

Nov 19, 2011 | Cars & Trucks

1 Answer

2007 dodge ram 4.4 beeps when i press the brake pedal but the tail light is out on the left side also. And when you turn on the left blinker it goes crazy fast and no light in the light assembly. Help?


If you have a beebing noise every time you press on the brake, it is because a tail light is burnt out. There are two filaments in each brake light. Therefore, when you turn on your hazards, it will appear that both tail lights work properly. The beebing warning sound is actually a feature that Dodge put in the Rams so drivers would know their tale light is out. Just replace the tail light bulb, and the beebing will automatically cease. To get the tail light housing out, you will need a torex screw driver. Also, you twist the bulb housing out as opposed to pulling it out. There are three prongs that twist out.

Jan 21, 2010 | 2007 Dodge Ram Truck

2 Answers

Right brake light out; tail light works fine


most rear tail lights and turn/stop lights are the same dual filiment bulb. it is possible for your tail light to work and your brake light not to and still have a bad bulb. I would check the bulb first, your brake light works on the left yes? this would mean that the fuse is fine

Mar 31, 2009 | 2006 Dodge Stratus

1 Answer

I have a 1997 dodge intrepid my brake lights are not working but the tail lights are so which bulb is the brake light , the one one on right or left.


first of all do you have a third brake light and does it work???? you could have a bad brake light switch turn on the head lights check all rear lamps then put on the 4 way flashers and check the bulbs the ones that dont light should be the brake lights or replace the tail lights they should be double fillament

Jan 29, 2009 | 1997 Dodge Intrepid

Not finding what you are looking for?
2000 Honda Accord Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...