Question about 1995 Buick Regal

1 Answer

Fuel tank removal. Do I need to remove fuel filter first it is in front of tank also anything else that needs to be removed before I lower the tank so nothing breaks Thanks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 207 Answers

You should be able to disconnect the fuel line from the pump housing and unplug the sending unit that should be everything you need to disconnect

Posted on Jun 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I remove the gas tank out of a 2006 Ford 500 no one knows


SECTION 310-01: Fuel Tank and Lines 2006 Freestyle/Five Hundred/Montego Workshop Manual REMOVAL AND INSTALLATION

All vehicles
  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02 .
  1. Release the fuel system pressure. For additional information, refer to Section 310-00 .
  1. Drain the fuel tank. For additional information, refer to Section 310-00 .
All wheel drive vehicles
  1. Remove the rear driveshaft. For additional information, refer to Section 205-00 .
All vehicles
  1. Remove the muffler. For additional information, refer to Section 309-00 .
  1. Disconnect the fuel vapor control tube assembly valve-to-fuel vapor tube quick connect coupling. For additional information, refer to Section 310-00 .
  1. Disconnect the fuel supply tube-to-fuel filter quick connect coupling. For additional information, refer to Section 310-00 .
  1. Disconnect the fuel vapor tube-to-fuel vapor control tube assembly valve quick connect coupling. For additional information, refer to Section 310-00 .
  1. Disconnect the fuel tank wiring harness electrical connector at the rear of the fuel tank.
  1. Release the clamp and remove the fuel tank filler hose from the fuel tank.
  1. Place a suitable lifting device under the fuel tank.
  1. Remove the 2 front fuel tank strap bolts.
    • To install, tighten to 35 Nm (26 lb-ft).
  1. NOTE: Do not bend the fuel tank straps.
    Loosen the 2 rear fuel tank strap bolts and position the 2 fuel tank straps aside.
  1. Lower the fuel tank enough to move forward, clear of the fuel straps then complete the lowering procedure.
  1. To install, reverse the removal procedure.

Procedure revision date: 08/19/2009


May 03, 2016 | Ford Cars & Trucks

1 Answer

Where is the full filter


I believe there is actually an access panel in front of the second row seat behind the drivers seat that you can access the top of the tank, fuel pump and possibly the fuel filter. Lift up the carpeting and check.
1. Remove the fuel tank cap to lower the fuel tank's internal pressure. 2. Locate access cover. 3. Remove the fuel pump & fuel filter assembly installation screws, then remove the fuel pump & fuel filter assembly from the fuel tank.



Mar 29, 2014 | 2004 Kia Sedona

1 Answer

Finding fuel filters


  • Hi, I can help.

  • You have to lower the tank a bit to get to the fuel filter.
  1. Relieve the fuel pressure.
  2. Remove the negative battery cable (make sure to plug a memory saver into your cigarette lighter first to preserve the radio codes).
  3. Now in a shop you would support the tank with a transmission jack so you could lower the tank a bit and raise it when finished. You may want to use a nice hydraulic floor jack.
  4. Now remove the fuel line on the front side of the gas tank.
  5. Remove the ground strap.
  6. Now double check to make sure the gas tank is stabilized and remove the bolts from the straps that hold the gas tank against the underside of the van.
  7. Now remove the "T" strap.
  8. Lower the tank just a few inches.
  9. Now take the lines off the fuel pump and remove the fuel filter.
  10. Install new fuel filter and tighten the bolts to 40 inch pounds as well as the tank straps.
  11. The "T" strap needs to be torqued to 250 inch pounds.

  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.

Regards, Tony

Sep 08, 2011 | 2001 Chrysler Town & Country

1 Answer

To replace the fuel filter?


Hello aperez657: My name is Roger and I will help you. The vehicle has only one fuel filter. The filter is part of the fuel pump assembly. To replace the filter you will need to remove the fuel pump from the fuel tank.You can remove the pump with out dropping the fuel tank. It is a chore though. (1) You need to disconnect the battery. (2) Remove the front seats.(3) Remove the front scuff plates.(4) Remove the rear scuff plates.(5) Remove the lower console cover.(6) Loosen the park brake lever bolts.(7) Partially peel back the carpeting until the service hole covering appears. (8) Remove the following in this order. (1) Service hole cover (2) Electrical connector (3) Disconnect plastic fuel lines (4) Remove fuel pump bolts. Reverse procedures to reinstall the pump.

Feb 02, 2011 | 2001 Mazda MPV

1 Answer

WHERE IS THE FUEL FILTER LOCATED FOR THE SEDONA 2004


believe there is actually an access panel in front of the second row seat behind the drivers seat that you can access the top of the tank, fuel pump and possibly the fuel filter. Lift up the carpeting and check.
1. Remove the fuel tank cap to lower the fuel tank's internal pressure. 2. Locate access cover. 3. Remove the fuel pump & fuel filter assembly installation screws, then remove the fuel pump & fuel filter assembly from the fuel tank.

Nov 29, 2010 | 2004 Kia Sedona

1 Answer

How to remove tank out of ford focus


TO REMOVE THE TANK U FIRST NEED A 13 MM SOCKET FOR THE FRONT BOLT. THEN YOU'LL NEED THREE NEW HOSE CLAMPS FOR THE FILLER NECK AND TWO FOR THE REAR FUEL LINES. PLACE A FLOOR JACK UNDER TANK AND REMOVE THE FRONT BOLT LOCATED BY THE FEUL FILTER. ONCE THE BOLT IS LOSE SLOWLY LOWER TANK TO AXCESS THE FILLER NECK END AND REAR FUEL LINES.TANK SHOULD BEABLE TO BE LOWERED ALL THE WAY AFTER U DID THIS. IF YOU NEED MORE HELP WRITE BACK TOO ME A GONESMOKING_420@YAHOO.COM.

I HAVE LOWERD MY TANK THREE DIFFERENT TIMES TO REMOVE FUEL PUMP

Nov 24, 2009 | 2000 Ford Focus

1 Answer

Where is the fuel filter on a 2002 caravan


You're probably not going to like this, but here's how you get to it...
REMOVAL
Release fuel pressure,
Disconnect the negative battery cable.
Raise vehicle and support.
Support the fuel tank with a transmission jack.
Remove fuel line from the front of the tank.
Remove ground strap
Remove the inboard side of the fuel tank straps and front T strap fastner.
Lower the tank about 6 inches.
Remove fuel lines from the fuel pump module.
Remove fuel filter from tank.

Oct 17, 2009 | 2002 Dodge Caravan

1 Answer

How to change the fuel filter for 2004 kia sedona


I believe there is actually an access panel in front of the second row seat behind the drivers seat that you can access the top of the tank, fuel pump and possibly the fuel filter. Lift up the carpeting and check.
1. Remove the fuel tank cap to lower the fuel tank's internal pressure. 2. Locate access cover. 3. Remove the fuel pump & fuel filter assembly installation screws, then remove the fuel pump & fuel filter assembly from the fuel tank.

Jul 02, 2009 | 2005 Kia Sedona

1 Answer

Starving for gas


check fuel filter first. rate as fixed if this helps.

Steel Midship, Aerostar
Removal and Installation
  1. NOTE: Make sure fuel tank (9002) is properly supported during removal and installation procedures.
    Drain fuel from fuel tank .
  1. Loosen fuel tank filler pipe clamp.
  1. Remove fuel tank heat shield (9A032) from vehicle.
  1. Support fuel tank .
  1. Remove bolt from rear fuel tank support strap (9092) and remove rear fuel tank support strap .
  1. Remove bolt from front fuel tank support strap and remove front fuel tank support strap .
  1. Partially lower fuel tank to gain access and remove feed and return lines from sender ports. To disconnect push connect fittings, refer to Push Connect Fittings in this section.
  1. Remove electrical connector from sender unit.
  1. Remove fuel vapor hose from evaporative emission valve (9B593) .
  1. Lower fuel tank from vehicle.

Apr 28, 2009 | 1995 Ford Aerostar

2 Answers

1999 jeep cherokee do you have to remove the fuel pump to replace


The combination Fuel Filter/Fuel Pressure Regulator is located on the fuel pump module. The fuel pump module is located on top of fuel tank.

The filter/regulator may be removed without removing fuel pump module although fuel tank must be removed.

REMOVAL
  1. Remove fuel tank. Refer to Fuel Tank Removal/Installation.
  2. Clean area around filter/regulator.
  3. Disconnect fuel line at filter/regulator. Refer to Quick-Connect Fittings for procedures.
  4. Remove retainer clamp from top of filter/regulator. Clamp snaps to tabs on pump module. Discard old clamp.
  5. Pry filter/regulator from top of pump module with 2 screwdrivers. Unit is snapped into module
  6. Discard gasket below filter/regulator.
    1. Before discarding filter/regulator assembly, inspect assembly to verify that O-rings are intact. If the smallest of the two O-rings can not be found on bottom of filter/regulator, it may be necessary to remove it from the fuel inlet passage in fuel pump module.
    INSTALLATION
    1. Clean recessed area in pump module where filter/regulator is to be installed.
    2. Obtain new filter/regulator (two new O-rings should already be installed)
    3. Apply a small amount of clean engine oil to O-rings. Do not install O-rings separately into fuel pump module. They will be damaged when installing filter/regulator.
    4. Install new gasket to top of fuel pump module.
    5. Press new filter/regulator into top of pump module until it snaps into position (a positive click must be heard or felt).
    6. The arrow molded into top of fuel pump module should be pointed towards front of vehicle (12 O'clock position).
    7. Rotate filter/regulator until fuel supply tube (fitting) is pointed towards front of vehicle (12 O'clock position).
    8. Install new retainer clamp (clamp snaps over top of filter/regulator and locks to flanges on pump module).
    9. Connect fuel line at filter/regulator. Refer to Quick-Connect Fittings for procedures.
    10. Install fuel tank. Refer to Fuel Tank Removal/Installation.
WARNING: THE FUEL SYSTEM IS UNDER CONSTANT FUEL PRESSURE EVEN WITH THE ENGINE OFF. THIS PRESSURE MUST BE RELEASED BEFORE SERVICING FUEL TANK .

Two different procedures may be used to drain fuel tank (lowering tank or using DRB scan tool).

The quickest draining procedure involves lowering the fuel tank.

As an alternative procedure, the electric fuel pump may be activated allowing tank to be drained at fuel rail connection. Refer to DRB scan tool for fuel pump activation procedures. Before disconnecting fuel line at fuel rail, release fuel pressure. Refer to the Fuel System Pressure Release Procedure for procedures. Attach end of special test hose tool number 6541, 6539, 6631 or 6923 at fuel rail disconnection (tool number will depend on model and/or engine application). Position opposite end of this hose tool to an approved gasoline draining station. Activate fuel pump and drain tank until empty.

If electric fuel pump is not operating, tank must be lowered for fuel draining. Refer to following procedures.

FUEL TANK REMOVAL
  1. Disconnect negative battery cable at battery.
  2. Release fuel system pressure. Refer to the Fuel System Pressure Release.
  3. Raise and support vehicle.
  4. If Equipped: Remove fuel tank skid plate.
  5. Remove 4 fuel hose shield mounting bolts and remove fuel hose shield from body.
    1. Remove fuel tank fill hose and vent hose clamps at fuel tank filler tube. Remove both hoses at fuel filler tube.
    2. Remove exhaust tailpipe heat shield mounting bolts and remove shield. CAUTION: To protect fuel tank from exhaust heat, this shield must reinstalled after tank installation.
    3. Place a hydraulic jack to bottom of fuel tank. WARNING: PLACE A SHOP TOWEL AROUND FUEL LINES TO CATCH ANY EXCESS FUEL .
      1. Disconnect fuel supply line from fuel extension line near front of fuel tank. Refer to Fuel Tubes/Lines/Hoses and Clamps. Also refer to Quick-Connect Fittings for procedures.
      2. Disconnect EVAP canister vent line near front of tank.
      3. Disconnect fuel pump module electrical connector (pigtail harness) near front of tank. Harness connector is clipped to body.
        1. Remove two fuel tank strap nuts. Position both tank support straps away from tank.
        2. Carefully lower right side of tank while feeding both fuel hoses through access hole in body. Fuel Tank Full And Not Drained Using DRB Scan Tool: To prevent fuel loss through hoses, keep left side of tank higher than right side while lowering. Do not allow hose openings to drop lower than top of tank.
        3. Continue lowering tank until clear of vehicle. Place tank on floor with left side (hose side) higher than right side
          1. Drain tank by removing fuel fill hose at tank. Fuel fill hose is largest of 2 hoses. Insert the drain hose (from an approved gasoline draining station) into hose opening. Drain tank until empty.
          2. If fuel pump module removal is necessary, refer to Fuel Pump Module Removal/installation for procedures.
          INSTALLATION
          1. If fuel pump module is being installed, refer to Fuel Pump Module Removal/installation for procedures.
          2. Install fuel fill/vent hoses to tank fittings. To prevent hose from kinking, rotate each hose until index mark on hose is aligned to index tang on fuel tank.
          3. Install hose clamps to hoses. Position clamps between index marks on each hose.
          4. Position fuel tank to hydraulic jack.
          5. Raise tank into position while guiding fuel fill and vent hoses into and through access hole in body.
          6. Continue raising tank until positioned to body.
          7. Attach two fuel tank mounting straps and mounting nuts. Tighten nuts to 10 Nm (90 in. lbs.) torque. Do not over tighten nuts.
          8. Install both fuel hoses to fuel fill tube. Tighten both retaining clamps.
          9. Position fuel hose shield to body. Install and tighten 4 mounting bolts.
          10. Connect fuel pump module pigtail harness electrical connector near front of tank.
          11. Connect fuel pump module supply line near front of tank. Refer to Quick-Connect Fittings for procedures.
          12. Connect EVAP hose near front of tank.
          13. Install exhaust tailpipe heat shield.
          1. Install fuel tank skid plate (if equipped).
          1. Lower vehicle and connect battery cable to battery.

Feb 08, 2009 | 1999 Jeep Cherokee

Not finding what you are looking for?
1995 Buick Regal Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...