Question about 1999 Daewoo Nubira

1 Answer

Where is the camshaft sensor located at on a 1999 daewoo nubira?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 38 Answers

Remove eng cover. it is at the front of eng neer timing belt, to re place timing belt must come off good luck

Posted on Jun 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the camshaft position sensor located on a 2002 daewoo nubira?


  • Right on the front of the cylender head. Remove the connector and the mounting bolt and remove and replace.


ironfist109_439.jpg


  • Hope this helps.

Oct 28, 2011 | 2002 Daewoo Nubira

1 Answer

I HAVE A 2001 DAEWOO NUBIRA THAT RUNS FINE MOST THE TIME BUT OTHER TIMES IT LOSES POWER AND STALLS.SOMETIMES IT WILL CRANK RIGHT BACK AND STALL WHEN I PUT IN GEAR AND START TO GO.OTHER TIMES YOU HAVE TO...


If I recall correctly there was a recall on the camshaft position sensor. In some cases it would melt.
MAKE: DAEWOO MODEL: NUBIRA YEAR: 2001 DEFECT SUMMARY:
ON CERTAIN PASSENGER VEHICLES, THE CAMSHAFT POSITION SENSOR MAY MELT RESULTING IN A BURNING SMELL AND VISIBLE SMOKE, WHICH MAY SUBSEQUENTLY LEAD TO THE MELTING OF THE CAMSHAFT COVER AND THE CAMSHAFT POSITION SENSOR WIRE HARNESS.
CONSEQUENCE SUMMARY:
THIS COULD POSSIBLY CAUSE AN UNDERHOOD FIRE.
CORRECTIVE SUMMARY:
DEALERS WILL REPLACE THE CAMSHAFT POSITION SENSORS AND INSTALL AN ADDITIONAL FUSE. THE RECALL BEGAN ON SEPTEMBER 7, 2004. OWNERS SHOULD CONTACT DAEWOO AT 1-877-362-1234, OPTION 6, OR FIND A LOCAL DEALER THROUGH THEIR WEBSITE AT WWW.DAEWOOUS.COM.

Sep 15, 2010 | 2001 Daewoo Nubira

1 Answer

Where i can find the knock sensor location in my car for daewoo nubira 98


it will be some where around the bottom part of the engine i think at the back ok...

Mar 23, 2010 | 1999 Daewoo Nubira

3 Answers

Need cam torque specs


1999 to 2002 - 2.0L DOHC

Camshaft bearing cap bolts intake and exhaust.

N.m (INCH LBS)
8 ( 71 )

Jan 23, 2010 | 2001 Daewoo Nubira

1 Answer

Engine doesn't start anymore after engine check light came on.Cambelt is still ok. Engine did not overheat.


you need to scan the check engine light. it will tell you what part is bad. could be crank or camshaft sensor

Dec 28, 2009 | 1999 Daewoo Nubira

2 Answers

2000 Daewoo Nubira camshaft position sensor


on the front under timing belt cover ,back cam ,if its not their then back of head about 3inches along from the gear wheel end

Sep 11, 2009 | 2002 Daewoo Nubira

1 Answer

How do i replace the camshaft sensor on a 1999 daewoo nubira? do i have to take the timing belt off?


no dont need to take belt off if its twin cam by the sound of things
just top bolt which is inside cam belt cover remove top cam cover retainer clip in top centre if still there and then 10mm bolt in cam belt cover just down from top middle section of cover bend gently to get to cam sensor bolt if have too much trouble doing this whole cam belt cover needs removing, air box, accessory drive belt and engine mount will need jack to support engine and to reinstall mount

Jun 27, 2009 | 1999 Daewoo Nubira

1 Answer

2000 daewoo lanos where is located the tempeture sensor?


On my 1999 it is located near fan has 2 wires almost looks like a o2 sensor

Feb 09, 2009 | 2002 Daewoo Nubira

1 Answer

Daewoo nubira 2002


hi there, im guessing your crankshaft sensor has been damaged. its located under the crankshaft pulley.

Aug 25, 2008 | 1999 Daewoo Nubira

1 Answer

My daewoo lanos 2002 starts then cuts out almost straight away


change your camshaft sensor this is next to urbottom pulley

Aug 04, 2008 | 1999 Daewoo Nubira

Not finding what you are looking for?
1999 Daewoo Nubira Logo

Related Topics:

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...