Question about 2008 Dodge Ram 2500

1 Answer

What is the bolt pattern on a 2500 dodge - 2008 Dodge Ram 2500

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.


    An expert whose answer got voted for 20 times.

  • Expert
  • 133 Answers


Posted on Jul 28, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Will the bolt pattern of a ford escape match the bolt pattern of a dodge journey?

What bolts are you talking about ? More specific detail information would help.

Nov 12, 2016 | Ford Cars & Trucks

1 Answer

Install water pump to a 2005 dodge 318 engine

First remove the clutch fan. Big nut on the front of the pump. Use a long wrench and hammer to knock it loose. I also heat the nut up some, this softens the locktite on the pump and nut, easier to break loose. Once off lay it in the shroud. Remove the bolts to the shroud and lift them both out at the same time. This gives you easy access to the pump. Drain the coolant. remove the hoses. Look at the new pump to see where the bolt pattern is, remove the old pump, clean the engine surface. Razor blade works. Reinstall. A couple of hours work.

Jan 11, 2015 | 2005 Dodge Ram 2500 Truck

1 Answer

No low beam headlights , when ya flip to high beam they flash on and go off

Check the relays on the bottom most part of the inner fender under the hood. They're held in with 3, 10mm bolts I believe. The bolt pattern makes a little arrow, and they're black.

Dec 09, 2010 | 1998 Dodge Ram 2500 2WD

1 Answer

I have a 1995 Chevy 2500 6.5 turbo diesel and the blow. So I was wondering if theirs any gas engines that will bolt in its place? thanks D Hawkins

Any smallblock chevy to a bigblock chevy will bolt up. examples I would go with : 350 or a 454 . The 6.5 uses the same transmission bolt pattern as these engines. If it's an automatic the flywhell might still work on the 350 or 454.

Aug 04, 2010 | 1995 Chevrolet Silverado 2500

1 Answer

What is the wheel bolt 8lug pattern

Do you mean to tighten them?? think of it as a clock. With only 8 hours write them down on a piece of paper otherwise it sounds confusing. 12 o'clock, 6 o'clock, 9 o'clock, 3 o'clock. 10 o'clock, 4 o'clock, 2 o'clock, and 8 o'clock. If it's easier, clockwise starting at 12 o'clock: 1, 7, 4, 6, 2, 8, 3, 5,. Hope that's what you were asking for. Was a little vague.

Mar 01, 2010 | 2008 Dodge Ram 2500

1 Answer

I need the torque specs for the 4 hus assy bolts and the 2 caliper bracket bolts on a 2004 dodge 2500 you have them?

Caliper Bolts Torque ...... 24 ft. lbs
Hub/Bearing Bolt ........... 122 ft. lbs
Hub/Bearing Nut ............ 180 ft. lbs

Feb 06, 2010 | 2004 Dodge Ram 2500

1 Answer

What Wheel Bolt patten inchanges with a 96 dodge 4wd pick-up .what other makes (ford ,Jeep etc) inchanges with this wheel

According to

The bolt pattern for your dodge is 5 bolt / 139.7

A 1996 Ford F150 Pickup 4WD is the same bolt pattern.

A 1996 GMC Pickup 1500 4WD Extended Cab 4x4 Long Box is not the same, 5 bolt / 127

Check out the link and just enter the make and year then choose the model and it will give u the info.

Nov 22, 2009 | 1996 Dodge Ram 1500 Club Cab

2 Answers

Remove front rotor on a 1999 dodge 2500 4x4

Take off wheel
remove brake caliper
remove rotor

Sep 13, 2009 | 1999 Dodge Ram 2500 4WD

1 Answer

Tensioner pulley ram 2500

You have to replace the whole thing. Usually the whole tensioner has to be replaced it should be bolted to the block with a 15mm bolt or a Star fastener T-48 or T-50.

Apr 19, 2009 | 1999 Dodge Ram 2500 4WD

1 Answer

Starter replacement

3 Mounting bolts and 3 wire connections-Positive, negative and crank.

Dec 21, 2008 | 1999 Dodge Ram 2500 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

807 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides