1999 Oldsmobile Intrigue Logo

Related Topics:

A
Anonymous Posted on Jun 03, 2014

99 olds intrige noise grinding at start up stop once started changed starter on change

5 Related Answers

Anonymous

  • 2 Answers
  • Posted on Jul 15, 2008

SOURCE: oil change

After you turn the car off, press the Accelerator all the way to the floor and release it all the way back three time really fast. Then turn the car back on. If it's not three times, try five times. One of them works. I do this for my car too.

Marty -MI

Ad

Anonymous

  • 1118 Answers
  • Posted on Mar 30, 2009

SOURCE: 1995 Olds Achieva S Grinding upon starting

They make that kind of noise if its low on fluid, and also depending on how cold it is they will make a lot of noise because the colder it is the thicker the oil is and the harder it is to pump. I am not there to hear the starter, If the starter is making noise it will only be audiable while your on start, i dought starter will make that noise while its running unless the drive is sticking . Have both the pump and starter chk.out.

Anonymous

  • 3092 Answers
  • Posted on Nov 19, 2009

SOURCE: How much will it cost me to change the thermostate

Thermostat run's about $8.00 - $14.00, seal about $3.00. labor time to remove and install thermostat pre Mitchell Labor Guide is 1.0 hr x what ever the shop rate is pre hr.

Anonymous

  • 1 Answer
  • Posted on Jul 08, 2010

SOURCE: where is starter relay on 2000 olds intrige

battery good starter good but the car wont ignite the starter with the ignition key

Jonah Oneal

  • 14092 Answers
  • Posted on Oct 01, 2010

SOURCE: i have a 1999 olds

CHECK FUEL PUMP RELAY AND FUSE.IF ALL IS GOOD FUEL PUMP MORE LIKELY FAILING.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

New starter problems on a 99 suburban 1500 4wd 350 vortec

pull the starter and check the ring gear teeth for burrs and mashed teeth. Ensure that the new starter has the correct number of teeth on the pinion as required by the ring gear or you will have the wrong gear ratio for your vehicle. There are many engines that use the same starter motor but are differentiated by the number of teeth on the pinion. I suspect that will be why there is hard noise and kick back as that is the out of mesh gears trying to work
0helpful
1answer

Intermittent starting

Yes. When was the last time you had the starter changed? Has anyone crawled under the vehicle to check for a loose starter? If the starter does not engage it may be the starter solenoid ( the thing that drives the gears into contact before the starter actually turns ). This might not be ramming the gears together properly and that will cause the grinding noise, as well as an intermittent start.
0helpful
1answer

99 Mazda 626 2.0 changed starter 3x's. No start

Well it could be an engine problem, or a bad connection with one of the battery cables. The engine would require more voltage to crank when it is hot, but not that much.
You might want to have someone check the engine to see how much drag is has when hot, by turning the crank by hand.
0helpful
1answer

I have a cold start problem with our 99 Honda EX CRV. 185K Miles. Car eventually starts after several tries. Once it does start cold... there are no further starting problems the rest of the day... until...

Inside the fuel pump moduel in the gas tank is a little known part called a

FUEL PUMP CHECK VALVE ! The pupose of this check valve is to keep the fuel lines an fuel rail full of gas . Having it checked would involve hook up a fuel pressure gauge . An no it's not you starter .

http://www.thesaabsite.com/faqs/9-5%20(9600)/FAQ--fuel-system-category--fuel-pump-check-valve-issues.html?id=682
0helpful
1answer

My 99 Chevy truck makes a grinding sound when I try to start my truck

Was their any shims when you took off the first one, chevy's have shims to put the starter in the right place.
0helpful
1answer

Where is starter relay on 2000 olds intrige

battery good starter good but the car wont ignite the starter with the ignition key
0helpful
1answer

Engine won't turn over completely

You need to replace the Starter and Solinoid. The Solinoid comes on the New Starter. The Solinoid shorted out when the Battery Died and Damaged the Starter.
Not finding what you are looking for?

38 views

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

john h

Level 3 Expert

29494 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...