Question about 1994 Chevrolet Camaro

1 Answer

Thermostat location Need to find location of it's housing?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

If you follow the upper radiator hose, you will see where it is attached. There are only 2 small bolts holding it on (not counting the hose clamp)

Posted on Jun 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Problem locating thermostat on 2006 Dodge Ram 1500 Big Horn Editon


follow the lower radiator hose to the engine,you have to raise vechicle to see thermostat it is under the vechicle,the thermostat is in the housing where hose go to thermostat housing bolted to the engine, you need to remove hose.if you have the HEMI ENGINE follow top radiator hose to thermostat housing behind the AC COMPRESSOR.

Aug 30, 2012 | Cars & Trucks

2 Answers

I can't locate thermostat.


Locate Thermostat
The thermostat is normally located in the aluminium elbow that the top
radiator hose connects to. The elbow is usually held down by two bolts
and it is only necessary to remove these to replace the thermostat. It
may not be necessary to remove any hoses. Take care that the new
thermostat is correctly located in its rescess and the old gasketing has
been completely removed and that the new gasket has a smear of gasket
cement on it. While tightening the bolts, make sure that the elbow is
seating evenly and not catching on the edge of the thermostat or you could
crack the elbow.

Feb 03, 2011 | 1999 Chevrolet Venture

1 Answer

Need to locate thermostat in 2001 ford escape. i think it is stuck.


Welcome to Fixya

The thermostat is located on the side head of the engine on the drivers side. If you follow the upper radiator hose to the plastic thermostat housing, (this is where it is located). This is a 2 piece housing. 3 BOLTS hold the main water housing to the engine block (These do not need to be removed to change the thermostat. The three screws on the thermostat housing (usually torx heads) need to be removed. (where the upper radiator). Inside you will find the thermostat. Remember to replace the thermostat gasket at the same time and also some thermostats will only fit in a certain way so pay attention when the old is removed if there is a little hole (foget what it is called) at the 12 oclock position on the thermostat.

Thank you for using Fixya!

Dec 09, 2010 | 2001 Ford Escape

2 Answers

Check engine light is on . need to know where the thermostat is located


The thermostat is a black plastic water outlet housing connected to radiator hose. when replacing the thermostat the whole housing is replaced.

Nov 28, 2010 | 2006 Ford Fusion

2 Answers

Need to replace thermostat. Where is it located?


The thermostat is behind the housing that the upper hose is attached to on the engine.

Oct 22, 2010 | 1996 Jeep Grand Cherokee

2 Answers

Where is the thermostat located


77f1c56.jpg

Fig. The location of the thermostat and its housing on the 3.7L engine

  1. Disconnect negative battery cable at battery.
  2. Drain cooling system.
  3. Raise vehicle on hoist.
  4. Remove splash shield.
  5. Remove lower radiator hose clamp and lower radiator hose at thermostat housing.
  6. Remove thermostat housing mounting bolts, thermostat housing and thermostat .
To install:
  1. Clean mating areas of timing chain cover and thermostat housing.
  2. Install thermostat (spring side down) into recessed machined groove on housing assembly. Make sure rubber seal locating tab is positioned in the corresponding notch in the housing.
  3. Position thermostat housing on timing chain cover.
  4. Install two housing-to-timing chain cover bolts. Tighten bolts to 105 inch lbs. (12 Nm) torque.
  5. Install lower radiator hose on thermostat housing.
  6. Install splash shield.
  7. Lower vehicle.
  8. Fill cooling system.
  9. Connect negative battery cable to battery.
  10. Start and warm the engine. Check for leaks.

Hope helps (remember rated and comment this).

Aug 06, 2010 | 2002 Jeep Liberty

1 Answer

I think i have located the thermostat but there is something mounted about it that would have to be unbolted in order to get to the thermostat, does anyone know what this is and if i can get to the...


You state that you think you have located the thermostat. The part that will need to be unbolted and removed is the thermostat housing. Simply remove the radiator hose and remove the bolts holding the housing in place. You may need to tap the housing gently to break it loose. The thermostat is located in the housing. Be sure to carefully scrap off any remaining gasket on the thermostat housing and the engine where the housing sits. Replace the thermostat and install a new gasket, replace housing, tighten bolts evenly and reattach radiator hose. Top off the radiator to replace any lost coolant.

Jun 28, 2010 | 1998 Mercury Sable

1 Answer

How do you replace a thermostat on 97 astro


Hi:
Your thermostat is located under the thermostat housing, which is located where the upper radiator hose attaches to the engine. First you must drain the coolant out of your radiator, then disconnect the hose from the engine. Remove the bolts from the thermostat housing, and gently tap the housing to break it free. Remove the housing and the thermostat. Carefully clean the flat surfaces on the housing and the engine, before reassembly. You will need a new gasket too. Fill the engine up with the proper coolant mixture, then start the car and check for leaks!

Dec 15, 2009 | 1997 Chevrolet Astro

1 Answer

How to replace thermostat.What has to come off first?


Hi:
Your thermostat is located under the thermostat housing, which is located where the upper radiator hose attaches to the engine. First you must drain the coolant out of your radiator, then disconnect the hose from the engine. Remove the bolts from the thermostat housing, and gently tap the housing to break it free. Remove the housing and the thermostat. Carefully clean the flat surfaces on the housing and the engine, before reassembly. You will need a new gasket too. Fill the engine up with the proper coolant mixture, then start the car and check for leaks!

Dec 15, 2009 | 2003 Ford ZX2

3 Answers

Thermostat location 1995 jeep grand cher. straight 6


Thermostat is located on 4.0L I-6 on front cylinder head. The 3.7L V-6 thermostat is located where the lower radiator hose attaches to engine. The 4.7L V-8 thermostat is located where the lower radiator hose attaches to engine. The 5.7L V-8 thermostat is located where the upper radiator hose attaches to engine. The 3.9L V-6 and 5.9L V-8 Thermostat is located on front top of intake manfold (between alternator and ac compressor)

Jul 31, 2008 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
1994 Chevrolet Camaro Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...