Question about 1999 Isuzu Trooper

1 Answer

How do I replace a driver side headlight assembly on a 2000 Isuzo Trooper

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 81 Answers

Ha. Good luck:-
Take the sidelight out, and remove the radiator grill. Remove the trim under the headlamp-2 nuts. The remaining 2 bolt are abve and below the headlamp, then the whole thing slides to the centre and pops out.
It will take a couple of hours!

Posted on Jul 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removing low beam bulb on 05 subaruoutback


Whether they become damaged in an accident or simply burn out over time, your Subaru Outback's headlights may eventually need to be replaced. Fortunately, once you've purchased the right replacement bulb for your model year, performing the repair yourself is relatively easy. These instructions only apply to Outback models made after 2000.

  1. Undo the clips on the air intake ducts using a screwdriver and remove the duct from the engine compartment (driver's side bulb removal only.)

  2. 2

    Loosen the secured clip on the washer tank with a screwdriver and slide the tank horizontally to allow easier access to the headlight assembly (passenger's side bulb removal only.)

  3. 3

    Turn the bulb cover counterclockwise and remove it from the assembly.

  4. 4

    Disconnect the headlight electrical connector and undo the assembly retaining spring.

  5. 5

    Pull the old bulb directly out of the socket and replace it with the new one. Press the retaining spring back into place and reattach the electrical connector.

  6. 6

    Replace the bulb cover, and then turn on the engine. Test the new headlight to make sure it works before replacing the air intake duct or the washer tank and closing the hood.

    Replacing the High-Beam Bulbs
  1. 1

    Undo the clips on the air intake ducts using a screwdriver and remove the duct from the engine compartment ( drivers side bulb removal only.)

  2. 2

    Loosen the secured clip on the washer tank with a screwdriver and slide the tank horizontally to allow easier access to the headlight assembly (passenger's side bulb removal only.)

  3. 3

    Disconnect the headlight electrical connector and undo the assembly retaining spring.

  4. 4

    Turn the headlight bulb counterclockwise and pull it out of the socket.

  5. 5

    Reinstall the new bulb, replace the retaining spring and reconnect the electrical connector.

  6. 6

    Test the new headlight to make sure it works before replacing the air intake duct or the washer tank and closing the hood.

Sep 14, 2012 | Cars & Trucks

1 Answer

How do i change the driver side headlight bulb on a 2000 Lexus ES300


  • Open the hood of the ES300 and prop it open.

  • 2

    Look at the headlight assembly from the top down. Depending on your model year, there may be a plastic panel covering the top of the headlight assembly. If this is present, remove it by lifting all of the plastic clips around the edges and lifting it off.

  • Sponsored Links

  • 3

    Locate the three bolts that hold the headlight assembly in place. Two of the bolts are in the left and right rear corners of the assembly, and the third is on the side bordering the outside edge of the car, screwed into the back of the fender panel. Remove all of these bolts with a small adjustable wrench. Though they appear to be designed to be removed with a screwdriver, the way they're arranged makes it almost impossible to remove them with one.

  • 4

    Slide the entire headlight assembly forward a few inches so that you can reach the back of it.

  • 5

    Unscrew the plastic bulb socket assembly. This is the large, round component located right in the middle of the back of the main assembly. Turn it about a quarter turn to the left and you can pull it away from the main assembly. If you're replacing both the bulb and the main assembly, see the next section on how to replace the bulb, then resume this process



  • Read more: How to Change Headlights in a Lexus Es300 ' eHow.com http://www.ehow.com/how_5038522_change-headlights-lexus-es.html#ixzz1x1Ywyhkr

    Jun 05, 2012 | 2000 Lexus ES 300

    2 Answers

    Replace headlamp unit on 2000 Toyota echo


    How do I replace the headlight Assembly on my 2000 Toyoto Echo?

    Feb 25, 2011 | 2000 Toyota ECHO

    1 Answer

    Replace low beam drivers side headlight on 1993 olds cutlass supreme convertible


    Remove turn signal assembly (uses a torx 15 driver). This will expose the two 10mm bolts on the one side of the headlight assembly. Remove the plastic front grill (uses a torx 15 driver - there are about 6 screws). This will expose the other two 10mm bolts on the headlight assembly. Remove the four 10mm bolts to remove the headlight assembly and this will allow you access to the headlight you need to replace.

    Feb 18, 2011 | 1993 Oldsmobile Cutlass Supreme

    1 Answer

    I NEED PUT TRANSMISSION OIL I HAVA 1995 ISUZO TROOPER AUTOMATIC I DONT FIND THE LOCATION WHERE I CAN PUT SOMETING IOL PLEASE CAN YOU TELL ME


    there is a plug in the pan, with engine running , fluid should barely come out, if not, its low and you will need to "pump" it in, a repair shop may be best to check the fluid level.

    Dec 26, 2010 | 1995 Isuzu Trooper

    1 Answer

    I need to know the fuel pressure on oo isuzo


    FUEL PRESSURE IS 48 - 55 PSI. IF FUEL PRESSURE LOW REPLACE FUEL FILTER FIRST BEFORE BUYING A NEW FUEL PUMP.

    Jul 14, 2010 | 2002 Isuzu Trooper

    2 Answers

    How do i replace a headlight bulb on the drivers side of a 2000 chevy malibu


    I went to the library and got a book on the malibu. it sowed me step by step, how to do it thank you

    Jan 24, 2010 | 1997 Chevrolet Malibu

    2 Answers

    PIN CODE


    Best to contact the Isuzu dealer for assistance.

    Dec 12, 2008 | 1993 Isuzu Trooper

    1 Answer

    How do you replace a burnt out headlight on the Silverado 2001


    open hood and on the very top of head lamp housing there are two L shaped rods that push down to hold lamp assembly in turn rods ad remove,Lamp assembly pulls out and headlight can be accessed.

    Oct 19, 2008 | 2000 Chevrolet 2500

    Not finding what you are looking for?
    1999 Isuzu Trooper Logo

    307 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Isuzu Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Steve Hurc
    Steve Hurc

    Level 3 Expert

    450 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Are you an Isuzu Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...